kSIST prEN 17048:2017

Flexible sheets for waterproofing - Plastic and rubber sheets for waterproofing of concrete bridge decks and other trafficked areas of concrete - Definitions and characteristics

This European Standard specifies characteristics and performance of plastic and rubber sheets for waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles where the waterproofing is fully bonded to the concrete deck and fully bonded to the asphalt overlay.
This European Standard also states the test methods used for verifying the characteristics and gives rules for the assessment and verification of consistency of performance of the product.

Abdichtungsbahnen - Kunststoff- und Elastomerbahnen für Abdichtungen von Betonbrücken und anderen Verkehrsflächen aus Beton - Definitionen und Eigenschaften

Diese Europäische Norm legt die Eigenschaften und Leistung von Kunststoff- und Elastomerbahnen für die Abdichtung von Betonbrücken und anderen Verkehrsflächen aus Beton fest, bei denen das Abdichtungs¬system vollflächig mit dem Brückenüberbau und mit der Deckschicht aus Asphalt verbunden ist.
Ferner legt diese Europäische Norm die Prüf¬verfahren für die Beurteilung der Merkmale fest und enthält Regeln für die Bewertung und Überprüfung der Leistungsbeständigkeit des Produkts.

Feuilles souples d’étanchéité - Feuilles plastiques et élastomères pour l’étanchéité de ponts et autres surfaces en béton circulables par les véhicules - Définitions et caractéristiques

La présente Norme européenne spécifie les caractéristiques et les performances des feuilles plastiques et élastomères pour l’étanchéité de ponts en béton et autres surfaces en béton circulables par les véhicules lorsque le système d’étanchéité est totalement adhérent au tablier en béton et totalement adhérent au revêtement bitumineux qui y est rapporté.
La présente Norme européenne définit également les méthodes d’essai employées pour vérifier les caractéristiques et fournit des règles pour l’évaluation et la vérification de la constance des performances du produit.

Hidroizolacijski trakovi - Polimerni in elastomerni trakovi za hidroizolacijo betonskih premostitvenih objektov in drugih betonskih prometnih površin - Definicije in lastnosti

General Information

• Status: Not Published
• Public Enquiry End Date: 29-Nov-2016
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: VLA - Water proofing
• Current Stage: 5020 - Formal vote (FV) (Adopted Project)
• Start Date: 11-Dec-2017
• Due Date: 29-Jan-2018
• Completion Date: 11-Dec-2017
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Mandate: M/102 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on membranes
• Ref Project: FprEN 17048 - Flexible sheets for waterproofing - Plastic and rubber sheets for waterproofing of concrete bridge decks and other trafficked areas of concrete - Definitions and characteristics

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 17048:2016
01-november-2016
Hidroizolacijski trakovi - Polimerni in elastomerni trakovi za hidroizolacijo
betonskih premostitvenih objektov in drugih betonskih prometnih površin -
Definicije in lastnosti
Flexible sheets for waterproofing - Plastic and rubber sheets for waterproofing of
concrete bridge decks and other trafficked areas of concrete - Definitions and
characteristics
Abdichtungsbahnen - Kunststoff- und Elastomerbahnen für Abdichtungen von
Betonbrücken und anderen Verkehrsflächen aus Beton - Definitionen und Eigenschaften
Feuilles souples d’étanchéité - Feuilles plastiques et élastomères pour l’étanchéité de
ponts et autres surfaces en béton circulables par les véhicules - Définitions et
caractéristiques
Ta slovenski standard je istoveten z: prEN 17048
ICS:
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
oSIST prEN 17048:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 17048:2016

---------------------- Page: 2 ----------------------
oSIST prEN 17048:2016


DRAFT
EUROPEAN STANDARD
prEN 17048
NORME EUROPÉENNE

EUROPÄISCHE NORM

September 2016
ICS 91.100.50
English Version

Flexible sheets for waterproofing - Plastic and rubber
sheets for waterproofing of concrete bridge decks and
other trafficked areas of concrete - Definitions and
characteristics
Feuilles souples d'étanchéité - Feuilles plastiques et Abdichtungsbahnen - Kunststoff- und
élastomères pour l'étanchéité de ponts et autres Elastomerbahnen für Abdichtungen von Betonbrücken
surfaces en béton circulables par les véhicules - und anderen Verkehrsflächen aus Beton - Definitionen
Définitions et caractéristiques und Eigenschaften
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 254.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 17048:2016 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)
Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 Product characteristics . 8
4.1 General . 8
4.2 Sheet characteristics . 8
4.2.1 Visible defects . 8
4.2.2 Dimensions, tolerances and mass per unit area . 8
4.2.3 Tensile properties. 9
4.2.4 Water absorption . 9
4.2.5 Foldability at low temperature . 9
4.2.6 Flow resistance at elevated temperature . 9
4.2.7 Dimensional stability at elevated temperatures . 9
4.2.8 Thermal ageing behaviour . 9
4.3 Performance related characteristics . 10
4.3.1 General . 10
4.3.2 Bond strength . 10
4.3.3 Shear strength . 10
4.3.4 Crack bridging ability . 10
4.3.5 Compatibility by heat conditioning . 10
4.3.6 Resistance to compaction of an asphalt layer . 10
4.3.7 Behaviour of plastic and rubber sheets during application of mastic asphalt . 10
4.3.8 Bitumen compatibility . 10
4.3.9 Watertightness . 11
4.4 Dangerous substances . 11
5 Assessment and verification of constancy of performance – AVCP. 11
5.1 General . 11
5.2 Type testing . 11
5.2.1 General . 11
5.2.2 Test samples, testing and compliance criteria . 12
5.2.3 Test reports . 14
5.2.4 Shared other party results . 14
5.3 Factory production control (FPC) . 14
5.3.1 General . 14
5.3.2 Requirements . 15
5.3.3 Product specific requirements . 18
5.3.4 Initial inspection of factory and of FPC . 18
5.3.5 Continuous surveillance of FPC . 19
5.3.6 Procedure for modifications . 19
5.3.7 One-off products, pre-production products (e.g. prototypes) . 19
6 Product data sheet . 21
7 Marking, labelling and packaging . 22
Annex A (normative) Determination of dimensional stability at 160 °C . 23
2

---------------------- Page: 4 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)
A.1 General . 23
A.2 Procedure . 23
A.3 Precision of test method . 23
A.4 Test report . 23
Annex B (informative) Example of a product data sheet . 24
Annex ZA (informative) Relationship of this European Standard with Regulation (EU) No.
305/2011 . 27
ZA.1 Scope and relevant characteristics . 27
ZA.2 System of Assessment and Verification of Constancy of Performance (AVCP) . 28
ZA.3 Assignment of AVCP tasks . 29
Bibliography . 31

3

---------------------- Page: 5 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)
European foreword
This document (prEN 17048:2016) has been prepared by Technical Committee CEN/TC 254 “Flexible
sheets for waterproofing”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
4

---------------------- Page: 6 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)
1 Scope
This European Standard specifies characteristics and performance of plastic and rubber sheets for
waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles where the
waterproofing is fully bonded to the concrete deck and fully bonded to the asphalt overlay.
This European Standard also states the test methods used for verifying the characteristics and gives
rules for the assessment and verification of consistency of performance of the product.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
EN 495-5, Flexible sheets for waterproofing — Determination of foldability at low temperature — Part 5:
Plastic and rubber sheets for roof waterproofing
EN 1107-2, Flexible sheets for waterproofing — Determination of dimensional stability — Part 2: Plastic
and rubber sheets for roof waterproofing
EN 1110, Flexible sheets for waterproofing — Bitumen sheets for roof waterproofing — Determination of
flow resistance at elevated temperature
EN 1296, Flexible sheets for waterproofing — Bitumen, plastic and rubber sheets for roofing — Method of
artificial ageing by long term exposure to elevated temperature
EN 1548, Flexible sheets for waterproofing — Plastic and rubber sheets for roof waterproofing — Method
for exposure to bitumen
EN 1848-2, Flexible sheets for waterproofing — Determination of length, width, straightness and flatness
— Part 2: Plastic and rubber sheets for roof waterproofing
EN 1849-2, Flexible sheets for waterproofing — Determination of thickness and mass per unit area — Part
2: Plastic and rubber sheets
EN 1850-2, Flexible sheets for waterproofing — Determination of visible defects — Part 2: Plastic and
rubber sheets for roof waterproofing
EN 12311-2, Flexible sheets for waterproofing — Determination of tensile properties — Part 2: Plastic and
rubber sheets for roof waterproofing
EN 13375, Flexible sheets for waterproofing — Waterproofing of concrete bridge decks and other concrete
surfaces trafficable by vehicles — Specimen preparation
EN 13416, Flexible sheets for waterproofing — Bitumen, plastic and rubber sheets for roof waterproofing
— Rules for sampling
EN 13596, Flexible sheets for waterproofing — Waterproofing of concrete bridge decks and other concrete
surfaces trafficable by vehicles — Determination of bond strength
EN 13653, Flexible sheets for waterproofing — Waterproofing of concrete bridge decks and other concrete
surfaces trafficable by vehicles — Determination of shear strength
5

---------------------- Page: 7 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)
EN 14223, Flexible sheets for waterproofing — Waterproofing of concrete bridge decks and other concrete
surfaces trafficable by vehicles — Determination of water absorption
EN 14224, Flexible sheets for waterproofing — Waterproofing of concrete bridge decks and other concrete
surfaces trafficable by vehicles — Determination of crack bridging ability
EN 14691, Flexible sheets for waterproofing — Waterproofing of concrete bridge decks and other concrete
surfaces trafficable by vehicles — Compatibility by heat conditioning
EN 14692, Flexible sheets for waterproofing — Waterproofing of concrete bridge decks and other concrete
surfaces trafficable by vehicles — Determination of the resistance to compaction of an asphalt layer
EN 14693, Flexible sheets for waterproofing — Waterproofing of concrete bridge decks and other concrete
surfaces trafficable by vehicles — Determination of the behaviour of bitumen sheets during application of
mastic asphalt
EN 14694, Flexible sheets for waterproofing — Waterproofing of concrete bridge decks and other concrete
surfaces trafficable by vehicles — Determination of resistance to dynamic water pressure after damage by
pre-treatment
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 13375, EN 13416 and the
following apply.
3.1
waterproofing
action to prevent the passage of water from one plane to another
3.2
bridge waterproofing system
assembly of layers between a concrete bridge deck (or other trafficked areas of concrete) and an
overlay
Note 1 to entry: See Figure 1.
Note 2 to entry: Generally comprises a primer, the plastic and rubber sheet (or the assembly of several plastic
and rubber sheets) and the protection layer if specified by the manufacturer.
6

---------------------- Page: 8 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)

Key
1 concrete bridge deck
2 primer
3 plastic and rubber sheet(s)
4 protection layer
5 overlay (asphalt)
6 bridge waterproofing system (2 + 3 and 4 if specified)
Figure 1 — Schematic section of bridge waterproofing system
3.3
carrier
material incorporated into or onto a factory-made plastic and rubber sheet to ensure its stability and/or
mechanical resistance
3.4
backing
material incorporated onto a factory-made plastic and rubber sheet without a permanent mechanical
function
3.5
surfacing
material applied on one or both sides of plastic and rubber sheets, either as a permanent light surface
protection on the upper surface or as an anti-sticking substance of the plastic and rubber sheets
3.6
batch
amount of product manufactured to the same specification
3.7
manufacturer’s limiting value
MLV
value stated by the manufacturer to be met during testing
Note 1 to entry: The MLV can be a minimum or a maximum value according to statements made under product
characteristics of this European Standard.
3.8
manufacturer’s declared value
MDV
value declared by the manufacturer accompanied by a declared tolerance
7

---------------------- Page: 9 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)
3.9
primer
initial coating applied directly to the prepared concrete deck prior to the bridge waterproofing sheet
being installed to achieve adhesion to the concrete surface; the primer can be made up by one or more
layers of bituminous products or resin based products
3.10
plastic and rubber sheet
factory made flexible waterproofing sheet with or without internal or external incorporation of one or
more carriers, which can be rolled up or folded for easy transport to the site
3.11
protection layer
layer above the plastic and rubber sheet, the aim of which being to protect the sheet from mechanical
damage
Note 1 to entry: Depending on the bridge waterproofing system, this layer can have an additional waterproofing
function.
3.12
overlay
asphalt layer immediately above the bridge waterproofing system
4 Product characteristics
4.1 General
When a tolerance is defined by this European Standard it does not have to be declared by the
manufacturer.
When tested for purposes other than type testing or factory production control (see 5.1), the tests to
determine product characteristics indicated in this European Standard shall be started within one
month of delivery from the manufacturer.
4.2 Sheet characteristics
4.2.1 Visible defects
The product shall be free of visible defects, as determined in accordance with EN 1850-2.
4.2.2 Dimensions, tolerances and mass per unit area
The length, width and straightness shall be determined in accordance with EN 1848-2. The length and
width shall not be shorter than the manufacturer's limiting value. The maximum deviation from
straightness shall not exceed 20 mm per 10 m length, or in proportion for other lengths (e.g. 10 mm per
5 m length).
Where a product is specified by mass per unit area, it shall be measured in accordance with EN 1849-2,
and the results shall lie within the declared tolerance of the manufacturer's declared value.
Where a product is specified by thickness, it shall be measured in accordance with EN 1849-2 and the
results shall lie within the declared tolerance of the manufacturer's declared value.
Where sheets with surfacing are specified by thickness, the measurement of thickness may additionally
be carried out on the selvedge. This shall be declared in the report.
8

---------------------- Page: 10 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)
4.2.3 Tensile properties
The tensile properties shall be determined in accordance with EN 12311-2 and the results (for the
longitudinal and transverse directions) shall lie within the declared tolerance of the manufacturer's
declared value.
4.2.4 Water absorption
The content of water absorbed shall be determined in accordance with EN 14223. The water absorption
shall be less than or equal to the manufacturer's limiting value.
4.2.5 Foldability at low temperature
The foldability at low temperature shall be determined in accordance with EN 495-5 and shall be less
than or equal to the manufacturer's limiting value.
This test does not give results directly corresponding to the application conditions in practice. Results
should only be used to compare products of similar thickness and construction.
In the case of sheets where the reinforcement is placed in the cross section visually closer to the upper
surface, the test shall be performed on the bottom face only.
If the upper surface is covered with a non- woven (e.g. tissue, fleece, etc.) the test shall be performed on
the bottom side only.
If the sheet on the upper surface is covered with permanent light surface protection and where the
reinforcement is placed in the cross section visually closer to the upper surface the test shall be
performed on the bottom side only.
4.2.6 Flow resistance at elevated temperature
If a bituminous layer is part of the plastic or rubber sheet the flow resistance at elevated temperature
shall be determined in accordance with EN 1110. The result shall be greater than or equal to the
manufacturer's limiting value (MLV).
4.2.7 Dimensional stability at elevated temperatures
The dimensional stability at elevated temperature shall be determined in accordance with EN 1107-2
(6 h at 80 °C). The result shall be less than or equal to the manufacturer's limiting value.
For plastic and rubber sheets to be used with a layer of mastic asphalt directly on the plastic and rubber
sheet, the dimensional stability at elevated temperatures (1 h at 160 °C) shall be evaluated in
accordance with Annex A when subject to regulatory requirements, and may be evaluated when not
subject to such requirements. The test result shall be less than or equal to the manufacturer's limiting
value.
NOTE The test at 80 °C is intended to determine the dimensional changes as a result of production-induced
internal stresses under the effect of heat. When combined with a mastic asphalt layer, the effect of heat is much
larger and can cause severe shrinkage to the plastic and rubber sheet. This effect is therefore declared as well for
sheets intended for use in combination with a mastic asphalt layer.
4.2.8 Thermal ageing behaviour
In order to verify the thermal ageing behaviour of the product, characteristics shall be determined
before and after exposure in accordance with EN 1296 for a period of 12 weeks at 70 °C. The relevant
characteristics are the foldability at low temperature before and after aging. The foldability at low
temperature shall be determined in accordance with EN 495-5 (see 4.2.5) and the results shall lie
within the declared tolerance of the manufacturer's declared value.
9

---------------------- Page: 11 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)
The purpose of testing in accordance with EN 1296 is to characterize the long-term thermal stability of
plastic and rubber sheets. The test does not give results corresponding to the service conditions in
practice. Results should only be used to compare products of similar thickness, construction and
composition, and they cannot be used for general durability classification. The chosen exposure
duration for artificial ageing in accordance to EN 1296 has no relevance to a real product lifetime.
4.3 Performance related characteristics
4.3.1 General
Test specimens for performance-related testing shall be prepared in accordance with EN 13375. Where
a sheet can be used in more than one waterproofing system, some of the following tests shall require
repeating.
4.3.2 Bond strength
The bond strength shall be determined in accordance with EN 13596, and shall be greater than or equal
to the manufacturer's limiting value.
4.3.3 Shear strength
The shear strength shall be determined in accordance with EN 13653, and shall be greater than or equal
to the manufacturer's limiting value.
4.3.4 Crack bridging ability
Where required the crack bridging ability of fully bonded plastic and rubber sheets shall be determined
in accordance with EN 14224 and the temperature shall be lower than or equal to the manufacturer's
limiting value. Testing on type 3 specimens covers also type 1 specimens.
The crack bridging ability shall be evaluated when subject to regulatory requirements, and may be
evaluated when not subject to such requirements.
4.3.5 Compatibility by heat conditioning
The compatibility by heat conditioning shall be determined in accordance with EN 14691. The test
result shall be greater than or equal to the manufacturer's limiting value.
4.3.6 Resistance to compaction of an asphalt layer
For plastic and rubber sheets to be used with a compacted asphalt layer directly on the plastic and
rubber sheet, the resistance of the plastic and rubber sheet to compaction of an asphalt layer shall be
determined in accordance with EN 14692, method 1 or 2, and a resistant result is required to
demonstrate product compliance with this European Standard.
4.3.7 Behaviour of plastic and rubber sheets during application of mastic asphalt
Plastic and rubber sheets intended for use with a protection layer of mastic asphalt shall be tested to
determine its behaviour during application of mastic asphalt in accordance with EN 14693. The test
results shall be less than or equal to the manufacturer’s limiting value.
4.3.8 Bitumen compatibility
Plastic and rubber sheets intended for use with a contact with bitumen or asphalt shall be bitumen
compatible tested in accordance with EN 1548.
The sheet is compatible with bitumen if:
a) for sheets with an inner carrier the change in mass shall be less than or equal to 5 %;
10

---------------------- Page: 12 ----------------------
oSIST prEN 17048:2016
prEN 17048:2016 (E)
b) for sheets without an inner carrier or backing the change in Young’s modulus shall be less than or
equal to 50 %.
Results obtained by this test method from sheets without an inner carrier or backing can be applied to
sheets manufactured with same chemical formulation but having inner carrier or backing. The results
obtained on a given thickness apply to any product of the same formulation with greater thickness.
4.3.9 Watertightness
The watertightness of the plastic and rubber sheet (or double sheet system) shall be determined in
accordance with EN 14694 without pretreatment and shall give a pass result.
4.4 Dangerous substances
National regulations on dangerous substances may require verification and declaration on release, and
sometimes content, when construction products covered by this standard are placed on those markets.
In the absence of European harmonized test methods, verification and declaration on release/content
should be done taking into account national provisions in the place of use.
NOTE An informative database covering European and national provisions on dangerous substances is
available at the Construction web site on EUROPA accessed through:
http://ec.europa.eu/enterprise/construction/cpd-ds/
5 Assessment and verification of constancy of performance – AVCP
5.1 General
The compliance of the plastic and rubber sheets for waterproofing of concrete bridge decks and other
trafficked areas of concrete with the requirements of this standard and with the performances declared
by the manufacturer in the DoP (Declaration of Performance) shall be demonstrated by:
— determination of the product type;
— factory production control by the manufacturer, including product assessment.
The manufacturer shall always retain the overall control and shall have the necessary means to take
responsibility for the conformity of the product with its declared performance(s).
NOTE The assignment of tasks to the notified body(ies) and the manufacturer is shown in Annex ZA, (Table
ZA.3).
5.2 Type testing
5.2.1 General
All performances related to characteristics included in this standard shall be determined when the
manufacturer intends to declare the respective performances unless the standard gives provisions for
declaring them without performing tests. (e.g. use of previously existing data, CWFT and conventionally
accepted performance).
Assessment previously performed in acc
...