Footwear - Determination of coefficient of friction for footwear and sole components - Test method (ISO 24267:2020)

This method determines the coefficient of friction between footwear and floorings under conditions simulating those experienced in the phases of a typical walking step when slip is most likely to occur.
The method is applicable to all types of footwear, outsole units, heel top pieces (top lifts) and sheet soling materials.

Reibung - Prüfverfahren für Schuhe für den täglichen Gebrauch und Schuhbestandteile (ISO 24267:2020)

Dieses Dokument stellt ein Verfahren zur Bestimmung des Koeffizienten der Reibung zwischen Schuhen und Bodenbelägen zur Verfügung unter Nachbildung der Bedingungen, die in den Phasen eines typischen Gehschritts wahrgenommen werden, in denen das Auftreten von Rutschen am wahrscheinlichsten ist.
Das Verfahren ist anwendbar für alle Arten von Schuhen und Schuhbestandteilen, Laufsohleneinheiten, Absatzflecken (Deckflecken) und Werkstoffe für Sohlenplatten, mit Ausnahme von PSA Schuhen (Persönliche Schutzausrüstung) und für Schuhe für besondere Zwecke mit Spikes, Metallbolzen oder gleichwertig.

Chaussures - Détermination du coefficient de frottement pour les chaussures et éléments de semelle - Méthode d'essai (ISO 24267:2020)

Le présent document fournit une méthode pour déterminer le coefficient de frottement entre la chaussure et les revêtements de sol dans des conditions simulant celles des différentes phases typiques d'un pas lorsqu'un risque de glissade est très probable.
La présente méthode s'applique à tous les types de chaussures et composants de chaussure, de semelles d'usure, de bonbouts et de matériaux de feuilles de semelle, à l'exception des chaussures d'équipement de protection individuelle (EPI) et des chaussures destinées à un usage particulier comprenant des pics, crampons ou éléments similaires

Obutev - Določanje koeficienta trenja za obutev in sestavne dele podplata - Preskusne metode (ISO 24267:2020)

General Information

Status
Published
Public Enquiry End Date
31-Jan-2020
Publication Date
29-Nov-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
26-Nov-2020
Due Date
31-Jan-2021
Completion Date
30-Nov-2020

Buy Standard

Standard
EN ISO 24267:2021
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 24267:2020 - BARVE
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 24267:2021
01-januar-2021
Obutev - Določanje koeficienta trenja za obutev in sestavne dele podplata -
Preskusne metode (ISO 24267:2020)
Footwear - Determination of coefficient of friction for footwear and sole components -
Test method (ISO 24267:2020)
Reibung - Prüfverfahren für Schuhe für den täglichen Gebrauch und Schuhbestandteile
(ISO 24267:2020)
Chaussures - Détermination du coefficient de frottement pour les chaussures et
éléments de semelle - Méthode d'essai (ISO 24267:2020)
Ta slovenski standard je istoveten z: EN ISO 24267:2020
ICS:
61.060 Obuvala Footwear
SIST EN ISO 24267:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 24267:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 24267:2021


EN ISO 24267
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2020
EUROPÄISCHE NORM
ICS 61.060
English Version

Footwear - Determination of coefficient of friction for
footwear and sole components - Test method (ISO
24267:2020)
Chaussures - Détermination du coefficient de Schuhe - Bestimmung des Reibungskoeffizienten von
frottement pour les chaussures et éléments de semelle Schuhen und Sohlenbestandteilen - Prüfverfahren (ISO
- Méthode d'essai (ISO 24267:2020) 24267:2020)
This European Standard was approved by CEN on 12 October 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24267:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 24267:2021
EN ISO 24267:2020 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 24267:2021
EN ISO 24267:2020 (E)
European foreword
This document (EN ISO 24267:2020) has been prepared by Technical Committee ISO/TC 216
"Footwear" in collaboration with Technical Committee CEN/TC 309 “Footwear” the secretariat of which
is held by UNE.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2021, and conflicting national standards shall be
withdrawn at the latest by May 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 24267:2020 has been approved by CEN as EN ISO 24267:2020 without any modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 24267:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 24267:2021
INTERNATIONAL ISO
STANDARD 24267
First edition
2020-10
Footwear — Determination of
coefficient of friction for footwear and
sole components — Test method
Chaussures — Détermination du coefficient de frottement pour les
chaussures et éléments de semelle — Méthode d'essai
Reference number
ISO 24267:2020(E)
©
ISO 2020

---------------------- Page: 7 ----------------------
SIST EN ISO 24267:2021
ISO 24267:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 24267:2021
ISO 24267:2020(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 1
5 Apparatus and materials. 1
6 Sampling and conditioning . 2
6.1 Sampling . 2
6.2 Conditioning . 2
7 Preparation of sample and floor . 2
8 Test method . 2
8.1 Test modes and test conditions for footwear with low heel seat height . 2
8.2 Test modes and test conditions for unit soles . 3
8.3 Footwear or soles with heel and forepart moulded in one piece with full contact
with the floor in the waist area . 3
8.3.1 Samples with heel seat height lower than 80 mm . 4
8.3.2 Samples with heel seat height higher than 80 mm . 4
8.4 Footwear or soles with heel and forepart moulded in one piece without full
contact with the floor in the waist area . 6
8.5 Test on top pieces . 7
8.6 Test on sheet materials . 8
9 Test report . 8
© ISO 2020 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 24267:2021
ISO 24267:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 216, Footwear, in collaboration with
the European Committee for Standardization (CEN) Technical Committee CEN/TC 309, Footwear, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2020 – All rights reserved

---------------------- Page: 10 ----------------------
SIST EN ISO 24267:2021
INTERNATIONAL STANDARD ISO 24267:2020(E)
Footwear — Determination of coefficient of friction for
footwear and sole components — Test method
1 Scope
This document provides a method for determining the coefficient of friction between footwear and
floorings under conditions simulating those experienced in the phases of a typical walking step when
slip is most likely to occur.
The method is applicable to all types of footwear and footwear components, outsole units, heel top
pieces (top lifts) and sheet soling materials, excepting PPE footwear (Personal Protective Equipment)
and special purpose footwear containing spikes, metal studs or similar.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 13287:2019, Personal protective equipment — Footwear — Test method for slip resistance
3 Terms and definitions
For the purpo
...

SLOVENSKI STANDARD
oSIST prEN ISO 24267:2020
01-januar-2020
Trenje - Preskusne metode za vsakdanjo obutev in sestavne dele (ISO/DIS
24267:2019)
Friction - Test methods for casual footwear and components (ISO/DIS 24267:2019)
Reibung - Prüfverfahren für Schuhe für den täglichen Gebrauch und Schuhbestandteile
(ISO/DIS 24267:2019)
Frottement - Méthodes d'essai pour les chaussures de loisirs et leurs composants
(ISO/DIS 24267:2019)
Ta slovenski standard je istoveten z: prEN ISO 24267
ICS:
61.060 Obuvala Footwear
oSIST prEN ISO 24267:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 24267:2020

---------------------- Page: 2 ----------------------
oSIST prEN ISO 24267:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 24267
ISO/TC 216 Secretariat: UNE
Voting begins on: Voting terminates on:
2019-11-14 2020-02-06
Friction — Test methods for casual footwear and
components
ICS: 61.060
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 24267:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 24267:2020
ISO/DIS 24267:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 24267:2020
ISO/DIS 24267:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Principle . 1
3 Normative references . 1
4 Terms and definitions . 1
5 Apparatus and materials. 2
6 Sampling and conditioning . 2
6.1 Sampling . 2
6.2 Conditioning . 2
7 Test method . 3
7.1 Test modes and test conditions for footwear with low heel seat height . 3
7.2 Test modes and test conditions for unit soles . 3
7.3 Footwear or soles with heel and forepart moulded in one piece type 1 . 4
7.3.1 Samples with heel seat height lower than 80 mm . 4
7.3.2 Samples with heel seat height higher than 80 mm . 4
7.4 Footwear or soles with heel and forepart moulded in one piece type 2 . 5
7.5 Test on top pieces . 6
7.6 Test on sheet materials . 7
8 Test report . 7
Annex A (normative) Preparation of footwear, sole units, top pieces and sliders .8
© ISO 2019 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 24267:2020
ISO/DIS 24267:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 216, Footwear.
iv © ISO 2019 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 24267:2020
DRAFT INTERNATIONAL STANDARD ISO/DIS 24267:2019(E)
Friction — Test methods for casual footwear and
components
1 Scope
This method determines the coefficient of friction between footwear and floorings under conditions
simulating those experienced in the phases of a typical walking step when slip is most likely to occur.
The method is applicable to all types of footwear, excepting professional footwear (EPI), outsole units,
heel top pieces (top lifts) and sheet soling materials.
2 Principle
The footwear item and underfoot surface are brought into contact, subjected to a specified vertical
force for a short period of static contact then moved horizontally relative to one another at a constant
speed. The horizontal frictional force is measured at a given time after movement starts and the
dynamic coefficient of friction is calculated `for the particular conditions of the test.
3 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 13287, Personal protective equipment — Footwear — Test method for slip resistance
4 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
4.1
normal force
force applied to the surface through the footwear, perpendicular (90°) to the surface. The force includes
the weight of the footwear, shoemaking last (4.1.1 or 4.1.2) or mechanical foot (4.1.3) and mounting
4.2
frictional force
force parallel to the surface and against the direction of movement arising when footwear slides over
a surface
4.3
coefficient of friction CoF
ratio of the frictional force divided by the normal force
4.4
static contact time
time between initial contact of the footwear with the surface achieving a normal force of 50 N and the
beginning of movement
4.5
measurement period
time interval during which the frictional force measurement is taken and during which the test
conditions are satisfied
© ISO 2019 – All rights reserved 1

---------------------- Page: 7 ----------------------
oSIST prEN ISO 24267:2020
ISO/DIS 24267:2019(E)

4.6
floor
material (flooring), without contaminant (lubricant), to be used as the test surface
4.7
surface
floor, with or without contaminant (lubricant), against which the footwear is tested
4.8
calibration test value CTV
coefficient of friction between the Slider 96 and the test surface
5 Apparatus and materials
Use apparatus and materials referred to in ISO 13287:2019, Chapter 4, with the following exceptions:
1)
• Regarding standard shoemaking last, other lasts with the same dimensions of "STM603L lasts "
can also be used.
• Regarding test flooring surface, preferably use pressed ceramic tile, or the flooring called up in the
relevant performance requirements. Suitable surfaces include EUROTILE 2 referred to in Annex B
of ISO 13287:2019, other quarry tiles, vinyl, carpet or wood.
Additional materials/accessories needed to test samples according to 7.1 to 7.6:
• Cellulosic insole material of around 2 mm in thickness for testing soles which are going to be used
in the footwear with an insole (for testing according to 7.1).
• Means to secure the soles to the last, as mechanical means, double sided adhesive tape, seal,
adhesives, bands, etc. (for testing according to 7.1).
• Saw and/or sanding machine, for sample preparation (for testing according to 7.3).
• Mechanical systems to attach to the equipment spigot small-sized top-pieces, bigger top pieces,
Slider 96 test piece or other testing samples to the testing machine, that can be used to replace the
shoemaking lasts or mechanical foots (for testing according to 7.5).
• High-hardness rubber material of at least 50 mm × 50 mm (thickness of ≤ 2 mm), for small- sized top
piece testing (for testing according to 7.5).
• Metallic plate made of e. g. aluminium, of at least (180 × 80) mm and 2,5 mm thick, for sheet material
testing (for testing according to 7.6).
6 Sampling and conditioning
6.1 Sampling
Two samples shall be tested, right foot and left foot whenever possible, with the exception of top pieces
where 2 test pieces shall be tested and sheet material where 2 test pieces shall be tested per direction.
6.2 Conditioning
The test items shall be conditioned prior to the test at (23 ± 2) °C and (50 ± 5) %
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.