kSIST FprEN ISO 4892-1:2024
(Main)Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO/FDIS 4892-1:2024)
Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance (ISO/FDIS 4892-1:2024)
ISO 4892-1:2016 provides information and general guidance relevant to the selection and operation of the methods of exposure described in detail in subsequent parts. It also describes general performance requirements for devices used for exposing plastics to laboratory light sources. Information regarding performance requirements is for producers of artificial accelerated weathering or artificial accelerated irradiation devices.
NOTE In this part of ISO 4892, the term "light source" refers to radiation sources that emit UV radiation, visible radiation, infrared radiation or any combination of these types of radiation.
ISO 4892-1:2016 also provides information on the interpretation of data from artificial accelerated weathering or artificial accelerated irradiation exposures. More specific information about methods for determining the change in the properties of plastics after exposure and reporting these results is given in ISO 4582.
Kunststoffe - Künstliches Bestrahlen oder Bewittern in Geräten - Teil 1: Allgemeine Anleitung (ISO/FDIS 4892-1:2024)
Plastiques - Méthodes d'exposition à des sources lumineuses de laboratoire - Partie 1: Lignes directrices générales (ISO/FDIS 4892-1:2024)
ISO 4892-1:2016 fournit des informations et un guide général pour la sélection et l'application des méthodes d'exposition détaillées dans les autres parties de la norme. Elle décrit également les exigences générales de performance des dispositifs utilisés pour exposer les plastiques aux sources lumineuses de laboratoire. Les informations relatives aux exigences de performance sont destinées aux fabricants d'appareillages d'essai de vieillissement accéléré artificiel ou d'irradiation accélérée artificielle.
NOTE Dans la présente partie de l'ISO 4892, le terme "source lumineuse" désigne les sources de rayonnement qui émettent un rayonnement UV, visible ou infrarouge, ou toute combinaison de ces types de rayonnement.
ISO 4892-1:2016 fournit également des informations sur l'interprétation des données issues des essais de vieillissement accéléré artificiel ou d'irradiation accélérée artificielle. Des informations plus spécifiques sur les méthodes de détermination des changements de propriétés des plastiques après exposition et de notification des résultats sont données dans l'ISO 4582.
Polimerni materiali - Metode izpostavljanja laboratorijskim virom svetlobe - 1. del: Splošna navodila (ISO/FDIS 4892-1:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 4892-1:2023
01-december-2023
Polimerni materiali - Metode izpostavljanja laboratorijskim virom svetlobe - 1. del:
Splošna navodila (ISO/DIS 4892-1:2023)
Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance
(ISO/DIS 4892-1:2023)
Kunststoffe - Künstliches Bestrahlen oder Bewittern in Geräten - Teil 1: Allgemeine
Anleitung (ISO/DIS 4892-1:2023)
Plastiques - Méthodes d'exposition à des sources lumineuses de laboratoire - Partie 1:
Lignes directrices générales (ISO/DIS 4892-1:2023)
Ta slovenski standard je istoveten z: prEN ISO 4892-1
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 4892-1:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 4892-1:2023
oSIST prEN ISO 4892-1:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 4892-1
ISO/TC 61/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-10-03 2023-12-26
Plastics — Methods of exposure to laboratory light
sources —
Part 1:
General guidance
Plastiques — Méthodes d'exposition à des sources lumineuses de laboratoire —
Partie 1: Lignes directrices générales
ICS: 83.080.01
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 4892-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 4892-1:2023
ISO/DIS 4892-1:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 4892-1
ISO/TC 61/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:
Plastics — Methods of exposure to laboratory light
sources —
Part 1:
General guidance
Plastiques — Méthodes d'exposition à des sources lumineuses de laboratoire —
Partie 1: Lignes directrices générales
ICS: 83.080.01
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 4892-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 4892-1:2023
ISO/DIS 4892-1:2023(E)
Contents Page
Foreword .iv
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Principle . 4
4.1 General . 4
4.2 Significance . . . 4
4.3 Use of accelerated tests with laboratory light sources . 5
5 Requirements for laboratory exposure devices . 6
5.1 Irradiance . 6
5.2 Temperature . 7
5.3 Humidity and wetting . 10
5.4 Other requirements for the exposure device . 11
6 Test specimens .12
6.1 Form, shape and preparation . 12
6.2 Number of test specimens .13
6.3 Storage and conditioning .13
7 Test conditions and procedure .13
7.1 Set points for exposure conditions . 13
7.2 Property measurements on test specimens. 14
7.3 Sampling for intermediate and final evaluation . 15
8 Periods of exposure and evaluation of test results.15
8.1 General . 15
8.2 Use of control materials .15
8.3 Use of results in specifications . 15
9 Test report .16
Annex A (normative) Procedures for measuring the irradiance uniformity in the specimen
exposure area .18
Annex B (informative) Factors that decrease the degree of correlation between artificial
accelerated weathering or artificial accelerated irradiation exposures and actual-
use exposures .21
Annex C (informative) Solar spectral irradiance standards .24
Bibliography .27
iii
oSIST prEN ISO 4892-1:2023
ISO/DIS 4892-1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 6,
Ageing, chemical and environmental resistance, in collaboration with the European Committee for
Standardization (CEN) Technical Committee CEN/TC 249, Plastics, in accordance with the Agreement
on technical cooperation between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 4892-1:2016), which has been technically
revised.
The main changes are as follows:
— definition of 3.2 and 3.5 clarified and Notes to entry added;
— definition and Notes to entry of 3.3 and 3.4 clarified;
— new terms and definitions and Notes to entry added for black-panel thermometer, black-standard
thermometer, white-panel thermometer, and white-standard thermometer (3.7 – 3.10);
— reference to ISO/TR 18486 added under 4.2.4;
— calibration requirements clarified in 5.1.7, 5.2.8, 5.2.9, 5.3.6;
— requirements regarding black-panel thermometer, black-standard thermometer, white-panel
thermometer, and white-standard thermometer in 5.2 and Table 2 clarified;
— reference to ISO 23741 added in 5.3.1;
— new Subclause 7.3 “Sampling for intermediate and final evaluation” added;
— requirements for the test report updated;
iv
oSIST prEN ISO 4892-1:2023
ISO/DIS 4892-1:2023(E)
— reference to CIE 85 in Annex C updated to CIE 241;
— editorial changes.
A list of all parts in the ISO 4892 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
v
oSIST prEN ISO 4892-1:2023
ISO/DIS 4892-1:2023(E)
Introduction
Plastics are often used outdoors or in indoor locations where they are exposed to solar radiation or to
solar radiation behind glass for long periods. It is therefore very important to determine the effects of
solar radiation, heat, moisture and ot
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.