SIST EN 302 217-3 V1.3.1:2009
(Main)Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 3: Equipment operating in frequency bands where both frequency coordinated or uncoordinated deployment might be applied - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment and antennas - Part 3: Equipment operating in frequency bands where both frequency coordinated or uncoordinated deployment might be applied - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
The present document specifies the essential requirements for point-to-point Digital Fixed Radio Systems (DFRS) operating in higher frequency bands, which propagation characteristics might be suitable for different frequency planning (see note 1). This would imply that, besides conventional link-by-link coordinated deployment, administrations may apply either no co-ordination at all (i.e. the band usage is free and the user is responsible for detecting a suitable interference-free operating frequency) or simplified co-ordination procedures based on the knowledge of existing links (e.g. through a public national data base) so that the impact of a possible new link could be evaluated on the basis of budgetary considerations of typical equipment receiver performances (which will not be considered related to essential requirements of article 3.2 of R&TTED [1]).
Fiksni radijski sistemi - Karakteristike in zahteve za opremo in antene tipa točka-točka - 3. del: Oprema, ki deluje v frekvenčnih pasovih, kjer se lahko uporablja usklajena in neusklajena oprema - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 302 217-3 V1.3.1:2009
01-november-2009
)LNVQLUDGLMVNLVLVWHPL.DUDNWHULVWLNHLQ]DKWHYH]DRSUHPRLQDQWHQHWLSDWRþND
WRþNDGHO 2SUHPDNLGHOXMHYIUHNYHQþQLKSDVRYLKNMHUVHODKNRXSRUDEOMD
XVNODMHQDLQQHXVNODMHQDRSUHPD+DUPRQL]LUDQL(1NL]DMHPDELVWYHQH]DKWHYH
þOHQDGLUHNWLYH5 77(
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment
and antennas - Part 3: Equipment operating in frequency bands where both frequency
coordinated or uncoordinated deployment might be applied - Harmonized EN covering
the essential requirements of article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 302 217-3 Version 1.3.1
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
33.120.40 Antene Aerials
SIST EN 302 217-3 V1.3.1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 302 217-3 V1.3.1:2009
---------------------- Page: 2 ----------------------
SIST EN 302 217-3 V1.3.1:2009
ETSI EN 302 217-3 V1.3.1 (2009-07)
Harmonized European Standard (Telecommunications series)
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 3: Equipment operating in frequency bands where
both frequency coordinated or
uncoordinated deployment might be applied;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 3 ----------------------
SIST EN 302 217-3 V1.3.1:2009
2 ETSI EN 302 217-3 V1.3.1 (2009-07)
Reference
REN/ATTM-04003
Keywords
DFRS, digital, DRRS, FWA, point-to-point, radio,
regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 302 217-3 V1.3.1:2009
3 ETSI EN 302 217-3 V1.3.1 (2009-07)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 12
3.3 Abbreviations . 12
4 Technical requirements specifications . 12
4.1 Environmental profile . 13
4.2 RF-channel selection . 13
4.2.1 RF-channel selection procedure . 13
4.2.2 Interference avoidance requirements . 13
4.2.2.1 Interference avoidance limit . 13
4.2.3 Frequency agile automatic channel selectio n . 14
4.3 Transmitter requirements . 14
4.3.1 Transmitter power . 14
4.3.1.1 Transmitter power . 14
4.3.1.2 Equivalent Isotropically Radiated Power (EIRP) . 14
4.3.1.3 Output Power Tolerance . 14
4.3.2 Radio Frequency (RF) spectrum mask. 14
4.3.3 Spurious emissions . 15
4.3.4 Radio frequency tolerance . 15
4.3.5 Antenna directional requirements . 15
4.3.5.1 Radiation Pattern Envelope (Off-axis EIRP density) . 15
4.3.5.2 Antenna gain . 15
4.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 16
4.4 Receiver requirements . 16
4.4.1 Spurious emissions . 16
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.2 RF-channel selection . 17
5.3 Essential radio test suites for the transmitter . 17
5.3.1 Transmitter power . 18
5.3.1.1 Transmitter power . 18
5.3.1.2 Equivalent Isotropically Radiated Power (EIRP) and EIRP density mask . 18
5.3.1.3 Output power tolerance . 18
5.3.2 RF spectrum mask . 18
5.3.3 Spurious emissions - external . 18
5.3.4 Radio frequency tolerance . 18
5.3.5 Antenna and system directional requirements . 19
5.3.5.1 Radiation pattern envelope (Off-axis EIRP density) . 19
5.3.5.2 Antenna gain . 19
5.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 19
5.4 Essential radio test suites for the receiver . 19
5.4.1 Spurious emissions . 20
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 21
ETSI
---------------------- Page: 5 ----------------------
SIST EN 302 217-3 V1.3.1:2009
4 ETSI EN 302 217-3 V1.3.1 (2009-07)
Annex B (normative): Wide radio-frequency band covering units and multirate equipment
specification and tests . 23
B.1 Wide radio-frequency band covering units . 23
B.2 Multirate/multiformat equipment . 25
Annex C (informative): The EN title in the official languages . 26
Annex D (informative): Bibliography . 27
Annex UA (normative): Frequency band around 58 GHz . 28
UA.0 Introduction . 28
UA.1 Digital systems . 28
UA.1.1 Frequency bands and channel arrangements . 28
UA.1.1.1 Frequency band . 28
UA.1.1.2 Radio channel arrangements . 28
UA.1.1.3 Transmission capacity. 28
UA.1.2 Transmitter . 29
UA.1.2.1 Transmitter power . 29
UA.1.2.2 Equivalent Isotropically Radiated Power (EIRP) . 29
UA.1.2.3 Output power tolerance . 29
UA.1.2.4 RF spectrum masks . 29
UA.1.2.4.1 Limits . 29
UA.1.2.4.2 Spectrum analyser settings . 30
UA.1.2.5 Spurious emissions-external . 30
UA.1.2.6 Radio frequency tolerance . 30
UA.1.2.7 RF-channel selection parameters . 30
UA.1.3 Receiver . 30
UA.2 Analogue systems . 31
UA.2.1 Frequency bands and channel arrangements . 31
UA.2.1.1 Frequency band . 31
UA.2.1.2 Radio channel arrangements . 31
UA.2.1.3 Transmission capacity. 31
UA.2.2 Transmitter . 31
UA.2.2.1 Transmitter power . 31
UA.2.2.2 Equivalent Isotropically Radiated Power (EIRP) . 31
UA.2.2.3 Output power tolerance . 31
UA.2.2.4 RF spectrum masks . 31
UA.2.2.5 Spurious emissions - external . 31
UA.2.2.6 RF frequency tolerance . 31
UA.2.3 Receiver requirements . 32
UA.2.3.1 Spurious emissions . 32
Annex UB (normative): Frequency band 64 GHz to 66 GHz . 33
UB.0 Introduction . 33
UB.1 Frequency bands and channel arrangements . 33
UB.1.1 Frequency band . 33
UB.1.2 Radio channel arrangements. 34
UB.1.3 Spectral efficiency . 34
UB.2 Transmitter . 35
UB.2.1 Transmitter power and Equivalent Isotropically Radiated Power (EIRP) . 35
UB.2.2 Output power tolerance . 36
UB.2.3 EIRP density masks . 37
UB.2.3.1 Limits . 37
UB.2.3.2 Emissions outside the 64 GHz to 66 GHz range . 38
UB.2.3.3 Spectrum analyser settings . 38
UB.2.4 Spurious emissions . 38
UB.2.5 Radio frequency tolerance . 38
ETSI
---------------------- Page: 6 ----------------------
SIST EN 302 217-3 V1.3.1:2009
5 ETSI EN 302 217-3 V1.3.1 (2009-07)
UB.2.6 RF-channel selection parameters . 38
UB.2.7 Antenna gain . 38
UB.3 Receiver . . 38
Annex UBa (normative): Frequency band 57 GHz to 66 GHz for point-to-point fixed wireless
systems . 39
UBa.0 Introduction . 39
UBa.1 Frequency bands and channel arrangements . 39
UBa.1.1 Frequency band . 39
UBa.1.2 Radio channel arrangements and nominal bandwidth . 40
UBa.1.3 Spectral efficiency . 40
UBa.2 Transmitter . 41
UBa.2.1 Transmitter power, antenna gain and Equivalent Isotropically Radiated Power (EIRP) . 41
UBa.2.2 Output power tolerance . 42
UBa.2.3 RF spectrum masks . 43
UBa.2.3.1 Limits . 43
UBa.2.3.2 Emissions outside the 57 GHz to 66 GHz range . 44
UBa.2.4 Spurious emissions . 45
UBa.2.5 Radio frequency tolerance . 45
UBa.2.6 Antenna gain . 45
UBa.3 Receiver . 45
Annex UC (normative): Frequency bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 46
UC.0 Introduction . 46
UC.1 Frequency bands and channel arrangements . 46
UC.1.1 Frequency band . 46
UC.1.2 Radio channel arrangements. 46
UC.1.3 Spectral occupancy and transmission capacity . 47
UC.2 Transmitter . 47
UC.2.1 Transmitter power and Equivalent Isotropic Radiated Power (EIRP) . 47
UC.2.2 Output power tolerance . 48
UC.2.3 Output power density masks . 49
UC.2.3.1 Limits . 49
UC.2.3.2 Emissions outside the 71 GHz to 76 GHz and 81 GHz to 86 GHz ranges. 50
UC.2.3.2.1 General requirement . 50
UC.2.3.2.2 Requirement for emissions above 86 GHz band edge . 50
UC.2.3.2.3 Conformance statement . 51
UC.2.3.3 Spectrum analyser settings . 51
UC.2.4 Spurious emissions-external . 51
UC.2.5 Radio frequency tolerance . 51
UC.2.6 RF-channel selection parameters . 51
UC.2.7 Antenna gain . 51
UC.3 Receiver . . 51
Annex UD (informative): Rationale for the interference limit formula . 52
UD.1 Analysis of the quality value for the channel selection procedure . 52
UD.1.1 Error-performance and availability requirements for Class A equipment . 52
UD.1.1.1 Example in the 58 GHz band . 52
UD.1.2 Theoretical background . 52
UD.1.3 Typical co-channel interference situation when channel rejection threshold is used . 53
UD.2 Protection capability of the RF-channel selection procedure . 54
UD.3 Frequency agility criteria. 55
ETSI
---------------------- Page: 7 ----------------------
SIST EN 302 217-3 V1.3.1:2009
6 ETSI EN 302 217-3 V1.3.1 (2009-07)
Annex UE (informative): Capacity and Receiver characteristics in the bands 64 GHz to
66 GHz, 71 GHz to 76 GHz and 81 GHz to 86 GHz. 56
UE.1 Band 64 GHz to 66 GHz . . 56
UE.1.1 BER as a function of receiver input signal level (RSL) . 56
UE.1.2 Co-channel and adjacent channel interference sensitivity . 57
UE.1.3 CW spurious interference . 57
UE.2 Bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 57
UE.2.1 Capacity . 57
UE.2.2 BER as a function of receiver input signal level (RSL) . 58
UE.2.3 Co-channel and adjacent channel interference sensitivity . 59
UE.2.4 CW spurious interference . 59
History . 60
ETSI
---------------------- Page: 8 ----------------------
SIST EN 302 217-3 V1.3.1:2009
7 ETSI EN 302 217-3 V1.3.1 (2009-07)
Intellectual Property
...
ETSI EN 302 217-3 V1.3.1 (2009-07)
Harmonized European Standard (Telecommunications series)
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 3: Equipment operating in frequency bands where
both frequency coordinated or
uncoordinated deployment might be applied;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 ETSI EN 302 217-3 V1.3.1 (2009-07)
Reference
REN/ATTM-04003
Keywords
DFRS, digital, DRRS, FWA, point-to-point, radio,
regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 217-3 V1.3.1 (2009-07)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 12
3.3 Abbreviations . 12
4 Technical requirements specifications . 12
4.1 Environmental profile . 13
4.2 RF-channel selection . 13
4.2.1 RF-channel selection procedure . 13
4.2.2 Interference avoidance requirements . 13
4.2.2.1 Interference avoidance limit . 13
4.2.3 Frequency agile automatic channel selectio n . 14
4.3 Transmitter requirements . 14
4.3.1 Transmitter power . 14
4.3.1.1 Transmitter power . 14
4.3.1.2 Equivalent Isotropically Radiated Power (EIRP) . 14
4.3.1.3 Output Power Tolerance . 14
4.3.2 Radio Frequency (RF) spectrum mask. 14
4.3.3 Spurious emissions . 15
4.3.4 Radio frequency tolerance . 15
4.3.5 Antenna directional requirements . 15
4.3.5.1 Radiation Pattern Envelope (Off-axis EIRP density) . 15
4.3.5.2 Antenna gain . 15
4.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 16
4.4 Receiver requirements . 16
4.4.1 Spurious emissions . 16
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.2 RF-channel selection . 17
5.3 Essential radio test suites for the transmitter . 17
5.3.1 Transmitter power . 18
5.3.1.1 Transmitter power . 18
5.3.1.2 Equivalent Isotropically Radiated Power (EIRP) and EIRP density mask . 18
5.3.1.3 Output power tolerance . 18
5.3.2 RF spectrum mask . 18
5.3.3 Spurious emissions - external . 18
5.3.4 Radio frequency tolerance . 18
5.3.5 Antenna and system directional requirements . 19
5.3.5.1 Radiation pattern envelope (Off-axis EIRP density) . 19
5.3.5.2 Antenna gain . 19
5.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 19
5.4 Essential radio test suites for the receiver . 19
5.4.1 Spurious emissions . 20
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 21
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 217-3 V1.3.1 (2009-07)
Annex B (normative): Wide radio-frequency band covering units and multirate equipment
specification and tests . 23
B.1 Wide radio-frequency band covering units . 23
B.2 Multirate/multiformat equipment . 25
Annex C (informative): The EN title in the official languages . 26
Annex D (informative): Bibliography . 27
Annex UA (normative): Frequency band around 58 GHz . 28
UA.0 Introduction . 28
UA.1 Digital systems . 28
UA.1.1 Frequency bands and channel arrangements . 28
UA.1.1.1 Frequency band . 28
UA.1.1.2 Radio channel arrangements . 28
UA.1.1.3 Transmission capacity. 28
UA.1.2 Transmitter . 29
UA.1.2.1 Transmitter power . 29
UA.1.2.2 Equivalent Isotropically Radiated Power (EIRP) . 29
UA.1.2.3 Output power tolerance . 29
UA.1.2.4 RF spectrum masks . 29
UA.1.2.4.1 Limits . 29
UA.1.2.4.2 Spectrum analyser settings . 30
UA.1.2.5 Spurious emissions-external . 30
UA.1.2.6 Radio frequency tolerance . 30
UA.1.2.7 RF-channel selection parameters . 30
UA.1.3 Receiver . 30
UA.2 Analogue systems . 31
UA.2.1 Frequency bands and channel arrangements . 31
UA.2.1.1 Frequency band . 31
UA.2.1.2 Radio channel arrangements . 31
UA.2.1.3 Transmission capacity. 31
UA.2.2 Transmitter . 31
UA.2.2.1 Transmitter power . 31
UA.2.2.2 Equivalent Isotropically Radiated Power (EIRP) . 31
UA.2.2.3 Output power tolerance . 31
UA.2.2.4 RF spectrum masks . 31
UA.2.2.5 Spurious emissions - external . 31
UA.2.2.6 RF frequency tolerance . 31
UA.2.3 Receiver requirements . 32
UA.2.3.1 Spurious emissions . 32
Annex UB (normative): Frequency band 64 GHz to 66 GHz . 33
UB.0 Introduction . 33
UB.1 Frequency bands and channel arrangements . 33
UB.1.1 Frequency band . 33
UB.1.2 Radio channel arrangements. 34
UB.1.3 Spectral efficiency . 34
UB.2 Transmitter . 35
UB.2.1 Transmitter power and Equivalent Isotropically Radiated Power (EIRP) . 35
UB.2.2 Output power tolerance . 36
UB.2.3 EIRP density masks . 37
UB.2.3.1 Limits . 37
UB.2.3.2 Emissions outside the 64 GHz to 66 GHz range . 38
UB.2.3.3 Spectrum analyser settings . 38
UB.2.4 Spurious emissions . 38
UB.2.5 Radio frequency tolerance . 38
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 217-3 V1.3.1 (2009-07)
UB.2.6 RF-channel selection parameters . 38
UB.2.7 Antenna gain . 38
UB.3 Receiver . . 38
Annex UBa (normative): Frequency band 57 GHz to 66 GHz for point-to-point fixed wireless
systems . 39
UBa.0 Introduction . 39
UBa.1 Frequency bands and channel arrangements . 39
UBa.1.1 Frequency band . 39
UBa.1.2 Radio channel arrangements and nominal bandwidth . 40
UBa.1.3 Spectral efficiency . 40
UBa.2 Transmitter . 41
UBa.2.1 Transmitter power, antenna gain and Equivalent Isotropically Radiated Power (EIRP) . 41
UBa.2.2 Output power tolerance . 42
UBa.2.3 RF spectrum masks . 43
UBa.2.3.1 Limits . 43
UBa.2.3.2 Emissions outside the 57 GHz to 66 GHz range . 44
UBa.2.4 Spurious emissions . 45
UBa.2.5 Radio frequency tolerance . 45
UBa.2.6 Antenna gain . 45
UBa.3 Receiver . 45
Annex UC (normative): Frequency bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 46
UC.0 Introduction . 46
UC.1 Frequency bands and channel arrangements . 46
UC.1.1 Frequency band . 46
UC.1.2 Radio channel arrangements. 46
UC.1.3 Spectral occupancy and transmission capacity . 47
UC.2 Transmitter . 47
UC.2.1 Transmitter power and Equivalent Isotropic Radiated Power (EIRP) . 47
UC.2.2 Output power tolerance . 48
UC.2.3 Output power density masks . 49
UC.2.3.1 Limits . 49
UC.2.3.2 Emissions outside the 71 GHz to 76 GHz and 81 GHz to 86 GHz ranges. 50
UC.2.3.2.1 General requirement . 50
UC.2.3.2.2 Requirement for emissions above 86 GHz band edge . 50
UC.2.3.2.3 Conformance statement . 51
UC.2.3.3 Spectrum analyser settings . 51
UC.2.4 Spurious emissions-external . 51
UC.2.5 Radio frequency tolerance . 51
UC.2.6 RF-channel selection parameters . 51
UC.2.7 Antenna gain . 51
UC.3 Receiver . . 51
Annex UD (informative): Rationale for the interference limit formula . 52
UD.1 Analysis of the quality value for the channel selection procedure . 52
UD.1.1 Error-performance and availability requirements for Class A equipment . 52
UD.1.1.1 Example in the 58 GHz band . 52
UD.1.2 Theoretical background . 52
UD.1.3 Typical co-channel interference situation when channel rejection threshold is used . 53
UD.2 Protection capability of the RF-channel selection procedure . 54
UD.3 Frequency agility criteria. 55
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 217-3 V1.3.1 (2009-07)
Annex UE (informative): Capacity and Receiver characteristics in the bands 64 GHz to
66 GHz, 71 GHz to 76 GHz and 81 GHz to 86 GHz. 56
UE.1 Band 64 GHz to 66 GHz . . 56
UE.1.1 BER as a function of receiver input signal level (RSL) . 56
UE.1.2 Co-channel and adjacent channel interference sensitivity . 57
UE.1.3 CW spurious interference . 57
UE.2 Bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 57
UE.2.1 Capacity . 57
UE.2.2 BER as a function of receiver input signal level (RSL) . 58
UE.2.3 Co-channel and adjacent channel interference sensitivity . 59
UE.2.4 CW spurious interference . 59
History . 60
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 302 217-3 V1.3.1 (2009-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Access, Terminals, Transmission and Multiplexing (ATTM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.19] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be publishe
...
Final draft ETSI EN 302 217-3 V1.3.1 (2009-05)
Harmonized European Standard (Telecommunications series)
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 3: Equipment operating in frequency bands where
both frequency coordinated or
uncoordinated deployment might be applied;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 302 217-3 V1.3.1 (2009-05)
Reference
REN/ATTM-04003
Keywords
DFRS, digital, DRRS, FWA, point-to-point, radio,
regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2009.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 302 217-3 V1.3.1 (2009-05)
Contents
Intellectual Property Rights . 7
Foreword . 7
Introduction . 8
1 Scope . 9
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 12
3.3 Abbreviations . 12
4 Technical requirements specifications . 12
4.1 Environmental profile . 13
4.2 RF-channel Selection . 13
4.2.1 RF-channel selection procedure . 13
4.2.2 Interference avoidance requirements . 13
4.2.2.1 Interference avoidance limit . 13
4.2.3 Frequency agile automatic channel selectio n . 14
4.3 Transmitter requirements . 14
4.3.1 Transmitter power . 14
4.3.1.1 Transmitter power . 14
4.3.1.2 Equivalent Isotropically Radiated Power (EIRP) . 14
4.3.1.3 Output Power Tolerance . 14
4.3.2 Radio Frequency (RF) spectrum mask. 14
4.3.3 Spurious emissions . 15
4.3.4 Radio frequency tolerance . 15
4.3.5 Antenna directional requirements . 15
4.3.5.1 Radiation Pattern Envelope (Off-axis EIRP density) . 15
4.3.5.2 Antenna gain . 15
4.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 16
4.4 Receiver requirements . 16
4.4.1 Spurious emissions . 16
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.2 RF-channel selection . 17
5.3 Essential radio test suites for the transmitter . 17
5.3.1 Transmitter power . 18
5.3.1.1 Transmitter power . 18
5.3.1.2 Equivalent Isotropically Radiated Power (EIRP) and EIRP density mask . 18
5.3.1.3 Output power tolerance . 18
5.3.2 RF spectrum mask . 18
5.3.3 Spurious emissions - external . 18
5.3.4 Radio frequency tolerance . 18
5.3.5 Antenna and system directional requirements . 19
5.3.5.1 Radiation pattern envelope (Off-axis EIRP density) . 19
5.3.5.2 Antenna gain . 19
5.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 19
5.4 Essential radio test suites for the receiver . 19
5.4.1 Spurious emissions . 20
Annex A (normative): HS Requirement and conformance Test specifications Table (HS-
RTT) . 21
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 302 217-3 V1.3.1 (2009-05)
Annex B (normative): Wide radio-frequency band covering units and multirate equipment
specification and tests . 23
B.1 Wide radio-frequency band covering units . 23
B.2 Multirate/multiformat equipment . 25
Annex C (informative): The EN title in the official languages . 26
Annex D (informative): Bibliography . 27
Annex UA (normative): Frequency band around 58 GHz . 28
UA.0 Introduction . 28
UA.1 Digital systems . 28
UA.1.1 Frequency bands and channel arrangements . 28
UA.1.1.1 Frequency band . 28
UA.1.1.2 Radio channel arrangements . 28
UA.1.1.3 Transmission capacity. 28
UA.1.2 Transmitter . 29
UA.1.2.1 Transmitter power . 29
UA.1.2.2 Equivalent Isotropically Radiated Power (EIRP) . 29
UA.1.2.3 Output power tolerance . 29
UA.1.2.4 RF spectrum masks . 29
UA.1.2.4.1 Limits . 29
UA.1.2.4.2 Spectrum analyser settings . 30
UA.1.2.5 Spurious emissions-external . 30
UA.1.2.6 Radio frequency tolerance . 30
UA.1.2.7 RF-channel selection parameters . 30
UA.1.3 Receiver . 30
UA.2 Analogue systems . 31
UA.2.1 Frequency bands and channel arrangements . 31
UA.2.1.1 Frequency band . 31
UA.2.1.2 Radio channel arrangements . 31
UA.2.1.3 Transmission capacity. 31
UA.2.2 Transmitter . 31
UA.2.2.1 Transmitter power . 31
UA.2.2.2 Equivalent Isotropically Radiated Power (EIRP) . 31
UA.2.2.3 Output power tolerance . 31
UA.2.2.4 RF spectrum masks . 31
UA.2.2.5 Spurious emissions - external . 31
UA.2.2.6 RF frequency tolerance . 31
UA.2.3 Receiver requirements . 32
UA.2.3.1 Spurious emissions . 32
Annex UB (normative): Frequency band 64 GHz to 66 GHz . 33
UB.0 Introduction . 33
UB.1 Frequency bands and channel arrangements . 33
UB.1.1 Frequency band . 33
UB.1.2 Radio channel arrangements. 34
UB.1.3 Spectral efficiency . 34
UB.2 Transmitter . 35
UB.2.1 Transmitter power and Equivalent Isotropically Radiated Power (EIRP) . 35
UB.2.2 Output power tolerance . 36
UB.2.3 EIRP density masks . 37
UB.2.3.1 Limits . 37
UB.2.3.2 Emissions outside the 64 GHz to 66 GHz range . 38
UB.2.3.3 Spectrum analyser settings . 38
UB.2.4 Spurious emissions . 38
UB.2.5 Radio frequency tolerance . 38
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 302 217-3 V1.3.1 (2009-05)
UB.2.6 RF-channel selection parameters . 38
UB.2.7 Antenna gain . 38
UB.3 Receiver . . 38
Annex UBa (normative): Frequency band 57 GHz to 66 GHz for point-to-point fixed wireless
systems . 39
UBa.0 Introduction . 39
UBa.1 Frequency bands and channel arrangements . 39
UBa.1.1 Frequency band . 39
UBa.1.2 Radio channel arrangements and nominal bandwidth . 40
UBa.1.3 Spectral efficiency . 40
UBa.2 Transmitter . 41
UBa.2.1 Transmitter power, antenna gain and Equivalent Isotropically Radiated Power (EIRP) . 41
UBa.2.2 Output power tolerance . 42
UBa.2.3 RF spectrum masks . 43
UBa.2.3.1 Limits . 43
UBa.2.3.2 Emissions outside the 57 GHz to 66 GHz range . 44
UBa.2.4 Spurious emissions . 45
UBa.2.5 Radio frequency tolerance . 45
UBa.2.6 Antenna gain . 45
UBa.3 Receiver . 45
Annex UC (normative): Frequency bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 46
UC.0 Introduction . 46
UC.1 Frequency bands and channel arrangements . 46
UC.1.1 Frequency band . 46
UC.1.2 Radio channel arrangements. 46
UC.1.3 Spectral occupancy and transmission capacity . 47
UC.2 Transmitter . 47
UC.2.1 Transmitter power and Equivalent Isotropic Radiated Power (EIRP) . 47
UC.2.2 Output power tolerance . 48
UC.2.3 Output power density masks . 49
UC.2.3.1 Limits . 49
UC.2.3.2 Emissions outside the 71 GHz to 76 GHz and 81 GHz to 86 GHz ranges. 50
UC.2.3.2.1 General requirement . 50
UC.2.3.2.2 Requirement for emissions above 86 GHz band edge . 50
UC.2.3.2.3 Conformance statement . 51
UC.2.3.3 Spectrum analyser settings . 51
UC.2.4 Spurious emissions-external . 51
UC.2.5 Radio frequency tolerance . 51
UC.2.6 RF-channel selection parameters . 51
UC.2.7 Antenna gain . 51
UC.3 Receiver . . 51
Annex UD (informative): Rationale for the interference limit formula . 52
UD.1 Analysis of the quality value for the channel selection procedure . 52
UD.1.1 Error-performance and availability requirements for Class A equipment . 52
UD.1.1.1 Example in the 58 GHz band . 52
UD.1.2 Theoretical background . 52
UD.1.3 Typical co-channel interference situation when channel rejection threshold is used . 53
UD.2 Protection capability of the RF-channel selection procedure . 54
UD.3 Frequency agility criteria. 55
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 302 217-3 V1.3.1 (2009-05)
Annex UE (informative): Capacity and Receiver characteristics in the bands 64 GHz to 66
GHz, 71 GHz to 76 GHz and 81 GHz to 86 GHz . 56
UE.1 Band 64 GHz to 66 GHz . . 56
UE.1.1 BER as a function of receiver input signal level (RSL) . 56
UE.1.2 Co-channel and adjacent channel interference sensitivity . 57
UE.1.3 CW spurious interference . 57
UE.2 Bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 57
UE.2.1 Capacity . 57
UE.2.2 BER as a function of receiver input signal level (RSL) . 58
UE.2.3 Co-channel and adjacent channel interference sensitivity . 59
UE.2.4 CW spurious interference . 59
History . 60
ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 302 217-3 V1.3.1 (2009-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Access, Terminals, Transmission and Multiplexing (ATTM), and is now submitted for the Vote phase of the ETSI
standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.19] (as amended) laying down a procedure for the provis
...
Draft ETSI EN 302 217-3 V1.3.1 (2008-11)
Harmonized European Standard (Telecommunications series)
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 3: Equipment operating in frequency bands where both frequency
coordinated or uncoordinated deployment might be applied;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 217-3 V1.3.1 (2008-11)
Reference
REN/ATTM-04003
Keywords
DFRS, digital, DRRS, FWA, point-to-point, radio,
regulation, transmission
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2008.
All rights reserved.
TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 217-3 V1.3.1 (2008-11)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 6
1 Scope . 8
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 11
3.3 Abbreviations . 11
4 Technical requirements specifications . 11
4.1 Environmental profile . 12
4.2 RF-channel Selection . 12
4.2.1 RF-channel selection procedure . 12
4.2.2 Interference avoidance requirements . 12
4.2.2.1 Interference avoidance limit . 12
4.2.3 Frequency agile automatic channel selectio n . 13
4.3 Transmitter requirements . 13
4.3.1 Transmitter power . 13
4.3.1.1 Transmitter power . 13
4.3.1.2 Equivalent Isotropically Radiated Power (EIRP) . 13
4.3.1.3 Output Power Tolerance . 13
4.3.2 Radio Frequency (RF) spectrum mask. 13
4.3.3 Spurious emissions . 14
4.3.4 Radio frequency tolerance . 14
4.3.5 Antenna directional requirements . 14
4.3.5.1 Radiation Pattern Envelope (Off-axis EIRP density) . 14
4.3.5.2 Antenna gain . 14
4.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 15
4.4 Receiver requirements . 15
4.4.1 Spurious emissions . 15
5 Testing for compliance with technical requirements . 15
5.1 Environmental conditions for testing . 15
5.2 RF-channel selection . 16
5.3 Essential radio test suites for the transmitter . 16
5.3.1 Transmitter power . 17
5.3.1.1 Transmitter power . 17
5.3.1.2 Equivalent Isotropically Radiated Power (EIRP) and EIRP density mask . 17
5.3.1.3 Output power tolerance . 17
5.3.2 RF spectrum mask . 17
5.3.3 Spurious emissions - external . 17
5.3.4 Radio frequency tolerance . 17
5.3.5 Antenna and system directional requirements . 18
5.3.5.1 Radiation pattern envelope (Off-axis EIRP density) . 18
5.3.5.2 Antenna gain . 18
5.3.5.3 Antenna Cross-Polar Discrimination (XPD) . 18
5.4 Essential radio test suites for the receiver . 18
5.4.1 Spurious emissions . 19
Annex A (normative): HS Requirement and conformance Test specifications
Table (HS-RTT) . 20
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 217-3 V1.3.1 (2008-11)
Annex B (normative): Wide radio-frequency band covering units and multirate equipment
specification and tests . 22
B.1 Wide radio-frequency band covering units . 22
B.2 Multirate/multiformat equipment . 24
Annex UA (normative): Frequency bands around 58 GHz . 25
UA.0 Introduction . 25
UA.1 Digital systems . 25
UA.1.1 Frequency bands and channel arrangements . 25
UA.1.1.1 Frequency band . 25
UA.1.1.2 Radio channel arrangements . 25
UA.1.1.3 Transmission capacity. 25
UA.1.2 Transmitter . 25
UA.1.2.1 Transmitter power . 25
UA.1.2.2 Equivalent Isotropically Radiated Power (EIRP) . 26
UA.1.2.3 Output power tolerance . 26
UA.1.2.4 RF spectrum masks . 26
UA.1.2.4.1 Limits . 26
UA.1.2.4.2 Spectrum analyser settings . 27
UA.1.2.5 Spurious emissions-external . 27
UA.1.2.6 Radio frequency tolerance . 27
UA.1.2.7 RF-channel selection parameters . 27
UA.1.3 Receiver . 27
UA.2 Analogue systems . 28
UA.2.1 Frequency bands and channel arrangements . 28
UA.2.1.1 Frequency band . 28
UA.2.1.2 Radio channel arrangements . 28
UA.2.1.3 Transmission capacity. 28
UA.2.2 Transmitter . 28
UA.2.2.1 Transmitter power . 28
UA.2.2.2 Equivalent Isotropically Radiated Power (EIRP) . 28
UA.2.2.3 Output power tolerance . 28
UA.2.2.4 RF spectrum masks . 28
UA.2.2.5 Spurious emissions - external . 28
UA.2.2.6 RF frequency tolerance . 28
UA.2.3 Receiver requirements . 29
UA.2.3.1 Spurious emissions . 29
Annex UB (normative): Frequency band 64 GHz to 66 GHz . 30
UB.0 Introduction . 30
UB.1 Frequency bands and channel arrangements . 30
UB.1.1 Frequency band . 30
UB.1.2 Radio channel arrangements. 30
UB.1.3 Spectral efficiency . 31
UB.2 Transmitter . 31
UB.2.1 Transmitter power and Equivalent Isotropically Radiated Power (EIRP) . 31
UB.2.2 Output power tolerance . 33
UB.2.3 EIRP density masks . 33
UB.2.3.1 Limits . 33
UB.2.3.2 Spectrum analyser settings . 34
UB.2.4 Spurious emissions . 34
UB.2.5 Radio frequency tolerance . 35
UB.2.6 RF-channel selection parameters . 35
UB.2.7 Antenna gain . 35
UB.3 Receiver . . 35
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 217-3 V1.3.1 (2008-11)
Annex UC (normative): Frequency bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 36
UC.0 Introduction . 36
UC.1 Frequency bands and channel arrangements . 36
UC.1.1 Frequency band . 36
UC.1.2 Radio channel arrangements. 36
UC.1.3 Spectral occupancy and transmission capacity . 37
UC.2 Transmitter . 37
UC.2.1 Transmitter power and Equivalent Isotropic Radiated Power (EIRP) . 37
UC.2.2 Output power tolerance . 39
UC.2.3 Output power density masks . 40
UC.2.3.1 Limits . 40
UC.2.3.2 Spectrum analyser settings . 41
UC.2.4 Spurious emissions-external . 41
UC.2.5 Radio frequency tolerance . 42
UC.2.6 RF-channel selection parameters . 42
UC.2.7 Antenna gain . 42
UC.3 Receiver . . 42
Annex UD (informative): Rationale for the interference limit formula . 43
UD.1 Analysis of the quality value for the channel selection procedure . 43
UD.1.1 Error-performance and availability requirements for Class A equipment . 43
UD.1.1.1 Example in the 58 GHz band: . 43
UD.1.2 Theoretical background . 43
UD.1.3 Typical co-channel interference situation when channel rejection threshold is used . 44
UD.2 Protection capability of the RF-channel selection procedure . 45
UD.3 Frequency agility criteria. 46
Annex UE (informative): Capacity and Receiver characteristics in the bands 64 GHz to
65 GHz, 71 GHz to 76 GHz and 81 GHz to 86 GHz. 47
UE.1 Band 64 GHz to 65 GHz . . 47
UE.1.1 BER as a function of receiver input signal level (RSL) . 47
UE.1.2 Co-channel and adjacent channel interference sensitivity . 48
UE.1.3 CW spurious interference . 48
UE.2 Bands 71 GHz to 76 GHz and 81 GHz to 86 GHz . 48
UE.2.1 Capacity . 48
UE.2.2 BER as a function of receiver input signal level (RSL) . 49
UE.2.3 Co-channel and adjacent channel interference sensitivity . 50
UE.2.4 CW spurious interference . 50
Annex UF (informative): The EN title in the official languages . 51
History . 52
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 217-3 V1.3.1 (2008-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Access, Terminals, Transmission and Multiplexing (ATTM), and is now submitted for the Public Enquiry phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.17] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [1] of the European Parliament and
of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Summary of Technical specifications relevant to Directive 1999/5/EC [1] are given in annex A.
The present document is part 3 of a multipart deliverable covering Fixed Radio Systems Characteristics and
requirements for point-to-point equipment and antennas. Full details of the entire series can be found in part 1 [8].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
Introduction
The EN 302 217 series has been produced in order to rationalize a large number of previous ETSI ENs dealing with
equipment and antennas for Point-to-Point (P-P) Fixed Service applications. For more details, see foreword in the
EN 302 217-1 [8].
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [1]. The modular
structure is described in EG 201 399 [i.2] and shown in Figure 1.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 217-3 V1.3.1 (2008-11)
3.3f
3.3e
Emergency*
3.3d Fraud*
3.3c Privacy*
3.3b
No harm to the network*
* If needed a
Scope by
Inter-working via the network*
equipement
3.3a
class or type
Inter-working with the network*
3.2 Use of Spectrum
Spectrum
New radio harmonized standards
Scoped by frequency and/or equipment type
Radio Product EMC
3.1b
EN 301 489 multi-part EMC standard
EMC
Generic and product standards also notified under EMC Directive
Standards covering Human Exposure to Electromagnetic Fields
relating to individual productcs
3.1a
New standards for acoustic safety
Safety
Standards also notified under LV Directive
Non-radio Radio (RE)
Non TTE
TTE
Legend:
Scope ot the present document: Any Point-to-point DFRS and
antennas in all frequency bands
NOTE: For article 3.1b the diagram shows EN 301 489, the multi-part product EMC standard for radio used under
the EMC Directive 89/336/EEC [i.1]. For Fixed Radio Systems EN, EN 301 489-1 [i.4] and
EN 301 489-4 [i.5] are relevant.
Figure 1: Modular structure for the various standards used under the R&TTE Directive
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 302 217-3 V1.3.1 (2008-11)
1 Scope
The present document specifies the essential requirements for point-to-point Digital Fixed Radio Systems (DFRS)
operating in higher frequency bands, which propagation characteristics might be suitable for different frequency
planning (see note). This would imply that, besides conventional link-by-link coordinated deployment, administrations
may apply either no co-ordination at all (i.e. the band usage is free and the user is responsible for detecting a suitable
interference-free operating frequency) or simplified co-ordination procedures based on the knowledge of existing links
(e.g. through a public national data base) so that the impact of a possible new link could be evaluated on the basis of
budgetary considerations of typical equipment receiver performances (which will not be considered related to essential
requirements of art 3.2 R&TTED [1]).
NOTE 1: For example, the frequency bands
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.