SIST EN 13245-1:2010
(Main)Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of PVC-U profiles
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of PVC-U profiles
This part of EN 13245 establishes a system of designation for profiles made of unplasticized poly(vinyl chloride) (PVC-U) intended to be used for building applications.
This part is applicable to light coloured and coloured PVC-U profiles, obtained by a mono-extrusion or a co-extrusion process, with a laminated foil or with a lacquered-coating.
It specifies test methods and test parameters.
This method of designation is intended to be used in product specification when the application is specified.
NOTE It is recommended to use this method for the designation of PVC-U profiles for information related to technical literature of the manufacturer, not for the marking of the products.
Profiles for the management of electrical power cables, communication cables and power track systems used for the distribution of electrical power and profiles for windows or doors are not covered by this European Standard. 1)
Kunststoffe - Profile aus weichmacherfreiem Poly(vinylchlorid) (PVC-U) für die Anwendung im Bauwesen - Teil 1: Bezeichnung von PVC-U Profilen
Der vorliegende Teil der EN 13245 legt ein Bezeichnungssystem zur Bezeichnung von Profilen aus weichmacherfreiem
Polyvinylchlorid (PVC-U) für die Anwendung im Bauwesen fest.
Dieser Teil gilt für hellfarbige und farbige, durch ein Monoextrusions- oder ein Koextrusionsverfahren
erhaltene PVC-U Profile mit einer beschichtetem Folie oder einer Lackschicht.
Es werden Prüfverfahren und Prüfparameter festgelegt.
Dieses Bezeichnungsverfahren ist für die Verwendung bei der Produktspezifikation vorgesehen, sobald die
Anwendung festgelegt ist.
ANMERKUNG Es wird empfohlen, dieses Verfahren zur Bezeichnung von PVC-U Profilen für Informationen in Bezug
auf die technische Literatur des Herstellers und nicht für die Kennzeichnung der Produkte zu verwenden.
Profile für die Führung elektrischer Stromkabel, Datenkabel und Stromschienen für die Verteilung von
elektrischem Strom und Fenster- oder Türprofile werden durch diese Europäische Norm nicht abgedeckt.1)
Plastiques - Profilés en poly(chlorure de vinyle) non plastifié (PVC-U) pour applications dans le bâtiment - Partie 1: Désignation des profilés en PVC-U
La présente partie de l'EN 13245 définit un système de désignation des profils fabriqués en poly(chlorure de
vinyle) non plastifié (PVC-U), destinés à être utilisés pour des applications dans le bâtiment.
La présente partie s'applique aux profilés en PVC-U colorés et de coloris clair, obtenus par mono-extrusion ou
co-extrusion, avec film plaxé ou une couche de laque.
Elle spécifie les méthodes et paramètres d'essai.
Le système de désignation défini est destiné à être utilisé dans la spécification des produits lorsque
l'application est spécifiée.
NOTE Il est recommandé d'utiliser ce système de désignation des profilés en PVC-U pour les informations liées à la
documentation technique du fabricant et non pour le marquage des produits.
La présente Norme européenne ne traite pas des profilés pour la gestion des câbles d'énergie électrique, des
câbles de communication et des chemins d'alimentation utilisés pour la distribution de l'énergie électrique ni
des profilés pour fenêtres et portes. 1)
Polimerni materiali - Profili iz nemehčanega polivinilklorida (PVC-U) za uporabo v gradbeništvu - 1. del: Označevanje profilov PVC-U
Ta evropski standard vzpostavlja sistem označevanje profilov iz nemehčanega polivinilklorida (PVC-U), namenjenih za uporabo v gradbeništvu. Ta del velja za rahlo obarvane in obarvane polivinilkloridne profile, pridobljene s postopkom mono- ali koekstruzije, z laminatno folijo ali brez ali z lakiranim premazom. Določa preskusne metode in preskusne parametre. Ta metoda označevanja se uporablja pri specifikaciji proizvoda, kadar je določen način uporabe.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Profile aus weichmacherfreiem Poly(vinylchlorid) (PVC-U) für die Anwendung im Bauwesen - Teil 1: Bezeichnung von PVC-U ProfilenPlastiques - Profilés en poly(chlorure de vinyle) non plastifié (PVC-U) pour applications dans le bâtiment - Partie 1: Désignation des profilés en PVC-UPlastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of PVC-U profiles83.140.99Drugi izdelki iz gume in polimernih materialovOther rubber and plastics productsICS:Ta slovenski standard je istoveten z:EN 13245-1:2010SIST EN 13245-1:2010en,fr,de01-september-2010SIST EN 13245-1:2010SLOVENSKI
STANDARDSIST EN 13245-1:20051DGRPHãþD
SIST EN 13245-1:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13245-1
June 2010 ICS 83.140.99 Supersedes EN 13245-1:2004English Version
Plastics - Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications - Part 1: Designation of PVC-U profiles
Plastiques - Profilés en poly(chlorure de vinyle) non plastifié(PVC-U) pour applications dans le bâtiment - Partie 1: Désignation des profilés en PVC-U
Kunststoffe - Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) für die Anwendung im Bauwesen -Teil 1: Bezeichnung von Profilen aus PVC-U This European Standard was approved by CEN on 19 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13245-1:2010: ESIST EN 13245-1:2010
EN 13245-1:2010 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .54 Designation of PVC-U profiles .65 Codification system for Data block 3 to Data block 5 .75.1 Vicat softening temperature (Data block 3) .75.2 Modulus of elasticity in flexure (Data block 3) .75.3 Nominal linear mass (Data block 4) .85.4 Heat reversion at 100 °C (Data block 4) .85.5 Impact resistance (Data block 4) .85.6 Durability (Data block 5) .96 Required characteristics for Type 3 and Type 4 profiles . 136.1 Resistance to cross cut (only for Type 4 profiles) . 136.2 Thermal resistance (only for Type 3 and Type 4 profiles) . 136.3 Water vapour resistance (only for Type 3 and Type 4 profiles, intended to be used for inside building applications) . 136.4 Peel strength (only for Type 3 profiles) . 137 Optional characteristics . 137.1 Resistance to staining . 137.2 Appearance and finishing of the coating (only for Type 3 and Type 4 profiles) . 148 Example of the designation of a PVC-U profile . 149 Use of reprocessable and recyclable material . 15Annex A (normative)
Determination of the linear mass . 16A.1 Apparatus . 16A.2 Test specimens . 16A.3 Procedure . 16A.4 Calculation and expression of results . 16Annex B (normative)
Determination of the impact resistance . 17B.1 Principle . 17B.2 Apparatus . 17B.3 Test specimens . 17B.4 Conditioning . 18B.5 Procedure . 18B.6 Expression of results . 19Annex C (normative)
Determination of peel strength . 20C.1 Principle . 20C.2 Apparatus . 20C.3 Preparation of test pieces . 21C.4 Conditioning . 21C.5 Procedure . 21C.6 Test report . 22Bibliography . 23 SIST EN 13245-1:2010
EN 13245-1:2010 (E) 3 Foreword This document (EN 13245-1:2010) has been prepared by Technical Committee CEN/TC 249 “Plastics”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2010, and conflicting national standards shall be withdrawn at the latest by December 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 13245-1:2004. EN 13245, Plastics
Unplasticized poly(vinyl chloride) (PVC-U) profiles for building applications, consists of the following parts: Part 1: Designation of PVC-U profiles Part 2: PVC-U profiles and PVC-UE profiles for internal and external wall and ceiling finishes Part 3: Designation of PVC-UE profiles It is a revision of EN 13245-1:2004 with the extension of the scope to: light coloured PVC-U profiles with or without a laminated foil or a lacquered-coating; coloured PVC-U profiles, obtained by a mono-extrusion or a co-extrusion process, with or without laminated foil or with
lacquered-coating. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 13245-1:2010
EN 13245-1:2010 (E) 4 1 Scope This European Standard establishes a system of designation for profiles made of unplasticized poly(vinyl chloride) (PVC-U) intended to be used for building applications. This part is applicable to light coloured and coloured PVC-U profiles, obtained by a mono-extrusion or a co-extrusion process, with or without a laminated foil or with a lacquered-coating.
It specifies test methods and test parameters.
This method of designation is intended to be used in product specification when the application is specified. NOTE It is recommended to use this method for the designation of PVC-U profiles for information related to technical literature of the manufacturer, not for the marking of the products. Profiles for the management of electrical power cables, communication cables and power track systems used for the distribution of electrical power, profiles for windows or doors and profiles for guttering are not covered by this European Standard.1) 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 438-2:2005, High-pressure decorative laminates (HPL) — Sheets based on thermosetting resins (usually called Laminates) — Part 2: Determination of properties EN 477:1995, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors — Determination of the resistance to impact of main profiles by falling mass EN 478, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors — Appearance after exposure at 150 °C — Test method EN 479, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors — Determination of heat reversion EN 513:1999, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors — Determination of the resistance to artificial weathering EN 20105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour (ISO 105-A02:1993)
EN ISO 105-A01:2010, Textiles — Tests for colour fastness — Part A01: General principles of testing (ISO 105-A01:2010) EN ISO 178, Plastics — Determination of flexural properties (ISO 178:2001) EN ISO 306:2004, Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) (ISO 306:2004) EN ISO 472:2001, Plastics — Vocabulary (ISO 472:1999)
1) Profiles that are excluded are in the scopes of standards prepared by CEN/TC 33, CENELEC/TC 213 or CEN/TC 128. SIST EN 13245-1:2010
EN 13245-1:2010 (E) 5 EN ISO 1043-1:2001, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) EN ISO 1163-2, Plastics — Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials — Part 2: Preparation of test specimens and determination of properties (ISO 1163-2:1995) EN ISO 2409, Paints and varnishes — Cross-cut test (ISO 2409:2007) EN ISO 2813, Paints and varnishes — Determination of specular gloss of non-metallic paint films at 20°, 60° and 85° (ISO 2813:1994, including Technical Corrigendum 1:1997) EN ISO 4624, Paints and varnishes — Pull-off test for adhesion (ISO 4624:2002) EN ISO 4892-2:2006, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps (ISO 4892-2:2006) EN ISO 8256:2004, Plastics — Determination of tensile-impact strength (ISO 8256:2004) ISO 7724-1:1984, Paints and varnishes — Colorimetry — Part 1: Principles ISO 7724-2:1984, Paints and varnishes — Colorimetry — Part 2: Colour measurement ISO 7724-3:1984, Paints and varnishes — Colorimetry — Part 3: Calculation of colour differences 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 472:2001 and
EN ISO 1043-1:2001 and the following apply. 3.1 PVC-U profile profile made of unplasticized poly(vinyl chloride) (PVC-U) material NOTE It applies to profiles made of non-cellular material as opposed to cellular material. 3.2 Type of profile
3.2.1 Type 1 profile PVC-U profile obtained by a mono-extrusion process (coloured in the mass) 3.2.2 Type 2 profile PVC-U profile obtained by a co-extrusion process 3.2.3 Type 3 profile PVC-U profile as Type 1 or Type 2 with laminated foil 3.2.4 Type 4 profile PVC-U profile as Type 1 or Type 2 with lacquer-coating 3.3 sight surface surface of a profile that is exposed to view, when the PVC-U profile is installed SIST EN 13245-1:2010
EN 13245-1:2010 (E) 6 3.4 coating
covering layer on the sight surface of a PVC-U profile, e.g. a co-extruded layer, a lacquer-coating or a laminated foil 3.5 laminated foil plastic layer bonded with an adhesive or under pressure and temperature to cover a surface of a PVC-U profile 3.6 co-extrusion
durable bonding of two thermoplastics [e.g. unplasticized polyvinylchloride (PVC-U) and poly(methyl methacrylate) (PMMA)] that are melted in separated extruders and fused together in the profile tool 3.7 lacquer-coating one or several layer(s) of lacquer (e.g. acrylic or polyurethane resin) or varnish (clear coating material) that cover(s) a PVC-U profile 3.8 radiant exposure time integral of irradiance, measured in joules per square metre (J/m−2) [ISO 9370:2009] 4 Designation of PVC-U profiles The PVC-U profiles are designated in accordance with a classification system of their characteristics. The designation consists of a description block and five data blocks as given in Table 1. SIST EN 13245-1:2010
EN 13245-1:2010 (E) 7 Table 1 — Designation of PVC-U profiles Description block Profile EN 13245-1 Data block 1: Material and profile type identification PVC-U – Type 1, Type 2, Type 3 a or Type 4 a
For types of profiles
See 3.2 Data block 2: Intended application One or more following codes depending on the intended application:
For outside building applications:
E For inside building applications:
I Data block 3: Material properties Vicat softening temperature (VST):
See 5.1 Modulus of elasticity in flexure:
See 5.2 Data block 4: Profile properties Nominal linear mass:
See 5.3 Heat reversion at 100 °C:
See 5.4 Impact resistance:
See 5.5 Data block 5: Durability See 5.6 a For Type 3 or Type 4 profiles, the requirements given in 6.1 to 6.4 shall be fulfilled, as applicable. 5 Codification system for Data block 3 to Data block 5 5.1 Vicat softening temperature (Data block 3) The Vicat softening temperature (VST) shall be measured in accordance with EN ISO 306:2004, Method B50, using 4 mm thick test specimens, prepared according to EN ISO 1163-2, as indicated in Table 2.
Table 2 — Preparation of test specimens Type of profile Compound to be tested Type 1 PVC-U compound Type 2, Type 3 and Type 4 Each of the extruded compounds, as applicable
The value of VST shall be coded according to Table 3. For Type 2, Type 3 and Type 4 profiles, as applicable, the values of the VST of each compound shall be coded from the internal layer to the external layer, with a separation by "/". 5.2 Modulus of elasticity in flexure (Data block 3) The modulus of elasticity in flexure, E, shall be measured in accordance with EN ISO 178, using a 4 mm thick test specimens prepared according to EN ISO 1163-2, as indicated in Table 2. For Type 2, Type 3 and Type 4 profiles, as applicable, the values of the modulus of elasticity in flexure of each compound shall be coded from the internal layer to the external layer, with a separation by "/". The value of the modulus of elasticity in flexure shall be coded according to Table 3.
SIST EN 13245-1:2010
EN 13245-1:2010 (E) 8 Table 3 — Codification for Data block 3
Vicat softening temperature (VST) Modulus of elasticity in flexure, E Range of values MPa Code The VST is represented by three figures giving the softening temperature. E.g. code 082 for a nominal VST value of
82 °C.
1 700 < E < 2 000 2 000 < E < 2 300 2 300 < E < 2 600 2 600 < E < 2 900 2 900 < E < 3 200 3 200 < E < 3 500 (1 700 + 300 × n) < E < (2 000 + 300 × n) a 17 20 23 26 29 32 "(17 + 3 × n)" a n is an integer.
5.3 Nominal linear mass (Data block 4) The nominal linear mass of the PVC-U profile shall be measured in accordance with Annex A. The value of the nominal linear mass shall be coded according to Table 4. 5.4 Heat reversion at 100 °C (Data block 4) The heat reversion at 100 °C of the PVC-U profile, R, shall be measured in accordance with EN 479. The value of the heat reversion at 100 °C shall be coded according to Table 4. 5.5 Impact resistance (Data block 4) The impact resistance of the PVC-U profile at 23 °C or, if required, at a low temperature (0 °C, - 10 °C, - 20 °C or - T' °C), shall be measured in accordance with Annex B. The value of the impact resistance shall be coded according to Table 4. SIST EN 13245-1:2010
EN 13245-1:2010 (E) 9 Table 4 — Codification for Data block 4
Nominal linear mass, PM Heat reversion at 100 °C Impact resistance at
T °C R % Code
Energy level J Code The nominal linear mass is represented by four figures giving the nominal linear mass. E.g. code 1483 for a nominal linear mass of 1 483 g/m. R ≤ 2 R ≤ 3 R ≤ n a
2 3 n
1 2 3 4 5 6 10 15 20 "(5 × m)" b (T,01) (T,02) (T,03) (T,04) (T,05) (T,06) (T,10) (T,15) (T,20) "[ T,(5 × m)]" a n is an integer. b m is an integer.
EXAMPLES
− Code (23,10) for a PVC-U profile with an impact resistance at 23 °C of 10 J; − Code (-20,05) for a PVC-U profile with an impact resistance at - 20 °C of 5 J. 5.6 Durability (Data block 5) 5.6.1 General Assessment of the durability is based on the following criteria: a) The colour differences between unexposed and exposed PVC-U profiles; b) The tensile-impact strength of the PVC-U profiles after ageing; c) The visual inspection of the PVC-U profiles after ageing; d) The adhesion of the coating of the PVC-U profiles after ageing (for Type 3 and Type 4 profiles, only). 5.6.2 Test methods for ageing 5.6.2.1 Outside building applications Ageing shall be carried out according to either an artificial ageing test method or a natural ageing test method. a) Artificial ageing test method according to EN 513:1999, Method 1 (referring to EN ISO 4892-2:2006, Method A). The conditions shall be defined in accordance with the code "A.n.T", where: 1) A means "artificial ageing"; SIST EN 13245-1:2010
EN 13245-1:2010 (E) 10 2) n
is the radiant exposure received by the exposed specimen, expressed in gigajoules per square metre, in the wavelength range 290 nm to 800 nm; 3) T is the black standard temperature (BST), if other than (60 ± 3) °C, as specified in EN 513:1999. EXAMPLE i) Codes A.8, A.12: a radiant exposure of 8 GJ/m² and 12 GJ/m² respectively, and a black standard temperature of 60 °C; ii) Code A.8.55: a radian
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.