Abstract

This part of IEC 61300 describes a test to quantitatively assess the capability of a connector terminating a reinforced cable of any diameter or a buffered fibre, both single-mode and multimode, to withstand static loads without uncoupling of the connector, physical damage to the assembly or permanent degradation of optical performance.

Status
Published
Public Enquiry End Date
31-May-2025
Publication Date
18-Nov-2026
Technical Committee
MOC - Mobile Communications
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
17-Nov-2026
Due Date
22-Jan-2027
Completion Date
19-Nov-2026

Buy Documents

Standard

SIST EN IEC 61300-2-50:2027

English language (14 pages)
Preview
Preview
e-Library read for
×1 day

SIST EN IEC 61300-2-50:2027 is the Slovenian standard for a fibre optic connector proof test with static load, published by SIST from IEC 61300-2-50. It specifies a test method for connectors terminated to reinforced cable or buffered fibre, in single-mode or multimode form, to check whether they can withstand static loads without uncoupling, physical damage, or permanent optical degradation.

What does SIST EN IEC 61300-2-50:2027 specify?

SIST EN IEC 61300-2-50:2027 specifies a quantitative test method for fibre optic connectors under static mechanical load. The document is aimed at proving whether the connector and cable assembly survives installation and maintenance stresses in practice.

The standard is organized into Scope, Normative references, Terms and definitions, General description, Apparatus, Test setup, Procedure, Severity, and Details to be specified and reported. Its figures show the test arrangements, and Table 1 links the test severity to the component type and performance category.

What are the key requirements of SIST EN IEC 61300-2-50:2027?

SIST EN IEC 61300-2-50:2027 requires the test item to be prepared, visually examined, cleaned, and inspected before loading. Clause 7.1 calls for visual examination and cleaning of mechanical and optical alignment parts, followed by inspection of the optical interfaces. In practice, this means the test starts from a known and documented condition.

The document requires preconditioning before the test. Clause 7.2 calls for at least 2 h at the standard atmospheric conditions from IEC 61300-1, so the DUT is conditioned before any optical measurement or load is applied.

The standard requires initial optical measurements and uses them as the reference for the result. Clause 7.3 says to measure the optical properties required by the relevant IEC 61753 series performance standard or IEC 62005 series reliability document, such as attenuation and return loss. That matters because the acceptance check is based on the change from the initial state, not only on visible damage.

Clause 7.4 defines how the DUT is mounted and which load directions apply. Straight pull at 0° and side pull at 90° are used as specified by the relevant performance or reliability document, and non-symmetrical connectors with circular cables are tested in both rotational orientations for side pull. For hardened connectors, the standard adds a straight pull test in the pulling cap - plug - cable configuration when a dedicated pulling cap is available.

The loading action must be smooth and controlled. Clause 7.4 requires the target load to be reached in 20 s or less, with a minimum application rate of 5 N/s for reinforced cables and 0,5 N/s for buffered fibres. This helps make results comparable across laboratories and avoids shock loading.

After loading, the standard requires post-test examination and optical verification. Clauses 7.5 to 7.8 require the operator to record whether the connector uncoupled or the cable assembly was damaged, then measure the optical properties again and compare them with the initial values. The plug shall remain mated until the final optical measurements are complete, which preserves a valid before-and-after comparison.

Clause 7.8 also requires visual inspection for damage and addresses sealing checks for hardened connectors. Sealed hardened connectors are checked with IEC 61300-2-38 Method A, while free breathing hardened connectors are checked with IEC 60529 and IEC TS 63334. In practice, this links the mechanical proof test to environmental protection performance.

Clause 8 ties the severity to the applied load and duration, with cases for buffered fibres, field-mountable connectors, and hardened connectors. Table 1 is the place to look when you need the test severity that matches the component type and performance category.

What terms does SIST EN IEC 61300-2-50:2027 define?

Device under test (DUT) - the connector assembly being evaluated in the proof test.

Pulling cap - a detachable component that protects the connector plug’s optical parts and can accept pulling gear.

Reinforced cable - the cable type used in the test scope when the connector is terminated to a strengthened cable assembly.

Buffered fibre - the fibre type covered by the scope when the connector is terminated to a buffered fibre.

Straight pull - loading applied along the connector axis, used at 0° in the procedure.

Side pull - loading applied at 90° to the connector axis, used to simulate lateral stress on the assembly.

Who uses SIST EN IEC 61300-2-50:2027?

SIST EN IEC 61300-2-50:2027 is used by fibre optic connector manufacturers, test laboratories, and reliability or qualification teams. It is also relevant to quality managers and buyers who need proof that a connector design can survive static mechanical loading during installation, maintenance, or field use.

The standard is especially relevant where products are assessed against IEC 61753 performance standards or IEC 62005 reliability documents. Those users need a repeatable way to document mechanical survival, optical stability, and sealing condition after the load test.

What changed in SIST EN IEC 61300-2-50:2027 from the previous edition?

SIST EN IEC 61300-2-50:2027 cancels and replaces the first edition published in 2007 as a technical revision. The stated changes are: a new normative references clause, a new terms and definitions clause, an added straight pull test for the pulling cap - plug - cable configuration, a revised procedure with provisions for hardened connectors, updated severities by component and performance category, and a new clause for details to be specified and reported.

Which standards are used with SIST EN IEC 61300-2-50:2027?

IEC 60529 provides the IP Code method used for sealing checks of free breathing hardened connectors. IEC 61300-1 supplies the general guidance and standard atmospheric conditions used for preconditioning.

IEC 61300-2-38 provides the sealing test method used for sealed hardened connectors after the proof test. IEC 61300-3-1 is used for visual examination before and after testing.

IEC 61300-3-3 provides the optical measurement method for attenuation and return loss monitoring. IEC 61300-3-35 is used for visual inspection of fibre optic connectors and fibre-stub transceivers.

IEC 61753 and IEC 62005 supply the performance and reliability documents that set the relevant optical limits and test expectations. IEC TR 62627-01 provides cleaning methods, and IEC TS 63334 supports sealing tests for passive optical protective housings and hardened fibre optic connectors.

What does the SIST EN IEC 61300-2-50:2027 document contain?

SIST EN IEC 61300-2-50:2027 contains a general description of the proof test, apparatus requirements, setup details, and a step-by-step procedure. It also includes guidance for specific loading cases, including adaptor - plug - cable and pulling cap - plug - cable arrangements.

The document uses Figure 1 to show the test setup and Figure 2 to show how load is applied for duplex cordage. Table 1 gives the test severities by component and performance category, which is the key reference for selecting the correct test condition.

The procedure covers preparation, preconditioning, initial optical measurements, mounting, loading, final measurements, and post-test examination. In practice, that gives users a complete laboratory method for qualification, verification, or comparative testing of fibre optic connector designs.

Relations

Effective Date
01-Jan-2027
Effective Date
01-Jan-2027
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026
Effective Date
27-Oct-2026

Buy Documents

Standard

SIST EN IEC 61300-2-50:2027

English language (14 pages)
Preview
Preview
e-Library read for
×1 day

Get Certified

Connect with accredited certification bodies for this standard

ANCE

Mexican certification and testing association.

EMA Mexico Verified

Intertek Slovenia

Intertek testing, inspection, and certification services in Slovenia.

UKAS Slovenia Verified

LNE (Laboratoire National de Métrologie et d'Essais)

French national laboratory for metrology and testing.

COFRAC France Verified

Sponsored listings

Frequently Asked Questions

SIST EN IEC 61300-2-50:2027 is a standard published by the Slovenian Institute for Standardization (SIST). Its full title is "Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-50: Tests - Fibre optic connector proof test with static load (IEC 61300-2-50:2026)". This standard covers: This part of IEC 61300 describes a test to quantitatively assess the capability of a connector terminating a reinforced cable of any diameter or a buffered fibre, both single-mode and multimode, to withstand static loads without uncoupling of the connector, physical damage to the assembly or permanent degradation of optical performance.

This part of IEC 61300 describes a test to quantitatively assess the capability of a connector terminating a reinforced cable of any diameter or a buffered fibre, both single-mode and multimode, to withstand static loads without uncoupling of the connector, physical damage to the assembly or permanent degradation of optical performance.

SIST EN IEC 61300-2-50:2027 is classified under the following ICS (International Classification for Standards) categories: 33.180.20 - Fibre optic interconnecting devices. The ICS classification helps identify the subject area and facilitates finding related standards.

SIST EN IEC 61300-2-50:2027 has the following relationships with other standards: It is inter standard links to SIST EN 61300-2-50:2007, SIST EN 61300-2-50:2007/AC:2015, SIST EN 62005-1:2002, SIST EN 62005-3:2002, SIST EN 62005-7:2005, SIST EN IEC 61300-2-38:2024, SIST EN 62005-2:2002, SIST EN IEC 61300-3-35:2023, SIST EN 62005-4:2001, SIST EN 61300-3-1:2006, SIST EN IEC 61753-021-06:2024, SIST EN IEC 61753-021-03:2026, SIST EN 61300-3-3:2009, SIST EN IEC 61753-021-02:2024, SIST EN IEC 61300-1:2022. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.

SIST EN IEC 61300-2-50:2027 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2027
Nadomešča:
SIST EN 61300-2-50:2007
SIST EN 61300-2-50:2007/AC:2015
Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni
postopki - 2-50. del: Preskusi - Preskus preverjanja optičnih konektorjev s statično
obremenitvijo (IEC 61300-2-50:2026)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-50: Tests - Fibre optic connector proof test with static
load (IEC 61300-2-50:2026)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-50: Prüfungen - Festigkeitsprüfung für Lichtwellenleiter-
Steckverbinder (IEC 61300-2-50:2026)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes
fondamentales d'essais et de mesures - Partie 2-50: Essais - Essai de résistance des
connecteurs à fibres optiques sous charge statique (IEC 61300-2-50:2026)
Ta slovenski standard je istoveten z: EN IEC 61300-2-50:2026
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61300-2-50

NORME EUROPÉENNE
EUROPÄISCHE NORM November 2026
ICS 33.180.20 Supersedes EN 61300-2-50:2007; EN 61300-2-
50:2007/AC:2015
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-50: Tests -
Fibre optic connector proof test with static load
(IEC 61300-2-50:2026)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Procédures fondamentales d'essais et de Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-
mesures - Partie 2-50: Essais - Essai de résistance des 50: Prüfungen - Festigkeitsprüfung für Lichtwellenleiter-
connecteurs fibroniques sous charge statique Steckverbinder
(IEC 61300-2-50:2026) (IEC 61300-2-50:2026)
This European Standard was approved by CENELEC on 2026-11-03. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2026 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61300-2-50:2026 E

European foreword
The text of document 86B/5246/FDIS, future edition 2 of IEC 61300-2-50, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61300-2-50:2026.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2027-11-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-11-30
document have to be withdrawn
This document supersedes EN 61300-2-50:2007 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61300-2-50:2026 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
Publication Year Title EN/HD Year
IEC 60529 - Degrees of protection provided by - -
enclosures (IP Code)
IEC 61300-1 - Fibre optic interconnecting devices and EN IEC 61300-1 -
passive components - Basic test and
measurement procedures - Part 1: General
and guidance
IEC 61300-2-38 2023 Fibre optic interconnecting devices and EN IEC 61300-2-38 2023
passive components - Basic test and
measurement procedures - Part 2-38:
Tests - Sealing for fibre optic sealed
closures and hardened connectors using
air pressure
IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures - Part 3-1:
Examinations and measurements - Visual
examination
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures - Part 3-3:
Examinations and measurements - Active
monitoring of changes in attenuation and
return loss
IEC 61300-3-35 - Fibre optic interconnecting devices and EN IEC 61300-3-35 -
passive components - Basic test and
measurement procedures - Part 3-35:
Examinations and measurements - Visual
inspection of fibre optic connectors and
fibre-stub transceivers
IEC 61753 series Fibre optic interconnecting devices and EN IEC 61753 series
passive components - Performance
standards
IEC 62005 series Reliability of fibre optic interconnecting EN 62005 series
devices and passive components
IEC/TR 62627-01 - Fibre optic interconnecting devices and - -
passive components - Part 01: Fibre optic
connector cleaning methods
IEC/TS 63334 - Fibre optic interconnecting devices and - -
passive components - Conditions for
testing the protection against dust and
water ingress of passive optical protective
housings and hardened fibre optic
connectors (IP5X, IPX4, IPX5, IPX6)

IEC 61300-2-50 ®
Edition 2.0 2026-09
INTERNATIONAL
STANDARD
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures -
Part 2-50: Tests - Fibre optic connector proof test with static load
ICS 33.180.20  ISBN 978-2-8327-1485-0

IEC 61300-2-50:2026-09(en)
IEC 61300-2-50:2026 © IEC 2026
CONTENTS
FOREWORD . 2
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 General description . 5
5 Apparatus . 5
5.1 General . 5
5.2 Mounting fixture . 5
5.3 Mandrel . 5
5.4 Force generator . 5
6 Test setup . 6
6.1 Fibre optic connector proof test with static load setup . 6
6.2 Optical measurement equipment . 7
7 Procedure . 7
7.1 Preparation of DUT . 7
7.2 Preconditioning . 7
7.3 Measure of initial optical properties . 7
7.4 Mounting of DUT . 7
7.5 Straight pull (pulling cap–plug–cable) . 8
7.6 Straight pull (adaptor–plug–cable) . 8
7.7 Side pull (adaptor–plug–cable) . 8
7.8 Final measurements and examinations . 8
8 Severity . 9
9 Details to be specified and reported . 9

Figure 1 – Fibre optic connector proof test with static load setup . 6
Figure 2 – Application of the load in the case of duplex cordage . 7

Table 1 – Test severities . 9

IEC 61300-2-50:2026 © IEC 2026
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 2-50: Tests - Fibre optic connector proof test with static load

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights.
IEC 61300-2-50 has been prepared by subcommittee 86B: Fibre optic interconnecting devices
and passive components, of IEC technical committee 86: Fibre optics. It is an International
Standard.
This second edition cancels and replaces the first edition published in 2007. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) addition of n
...