iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1253-1:2000

(Main)

Gullies for buildings - Part 1: Requirements

Gullies for buildings - Part 1: Requirements

This standard classifies gullies, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of material, for use in drainage systems operating under gravity including siphonic systems. Note: Although normally used to convey domestic waste water, industrial waste water and rainwater, gullies can convey other waste water provided there is no risk of damage to components or of injury to health. This standard does not apply to gully tops and manhole tops which are specified in EN 124.

Abläufe für Gebäude - Teil 1: Anforderungen

Diese Norm enthält die Klassenzuordnung für Abläufe, gibt eine Anleitung hinsichtlich der Einbaustellen und werkstoffunabhängige Anforderungen für Konstruktion, Ausführung, Funktion und Kennzeichnung für werkmäßig hergestellte Abläufe für Gebäude zur Verwendung in Schwerkraftentwässerungssystemen einschließlich Systemen mit Druckströmung.

Avaloirs et siphons pour bâtiments - Partie 1: Spécifications

Cette partie de norme européenne classifie les avaloirs et les siphons, établit un guide pour les lieux d'installation et spécifie les exigences pour la conception, la construction, les performances et le marquage des avaloirs et siphons pour bâtiments fabriqués en usine, indépendamment des matériaux, destinés a etre utilisés pour les systemes d'évacuation gravitaires, incluant les systemes d'évacuation siphoide.

Priključni jašek za kanalizacijo stavb - 1. del: Zahteve

General Information

Status
Withdrawn
Publication Date
31-Oct-2000
Withdrawal Date
30-Sep-2003
ICS
91.140.80 - Drainage systems
Technical Committee
IOVO - Water supply and waste water engineering
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
01-Oct-2003
Due Date
01-Oct-2003
Completion Date
01-Oct-2003
Directive
93/38/EEC - Procurement procedures of entities operating in the water, energy, transport and telecommunications sectors
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
EN 1253-1:1999 - Gullies for buildings - Part 1: Requirements

Relations

Replaced By
SIST EN 1253-1:2003 - Gullies for buildings - Part 1: Requirements
Effective Date
01-Oct-2003

Buy Standard

EN 1253-1:2000EN 1253-1:2000
PreviousNext
Standard
EN 1253-1:2000
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Abläufe für Gebäude - Teil 1: AnforderungenAvaloirs et siphons pour bâtiments - Partie 1: SpécificationsGullies for buildings - Part 1: Requirements91.140.80Drenažni sistemiDrainage systemsICS:Ta slovenski standard je istoveten z:EN 1253-1:1999SIST EN 1253-1:2000en0
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 12889:2023(Main)
Trenchless construction and testing of drains and sewers
EN 12889:2022

This document is applicable to the trenchless construction, trenchless replacement techniques and testing of new drains and new sewers in the ground usually operating as gravity or pressure pipelines, formed using prefabricated pipes and their joints.
Renovation techniques for existing pressure and non-pressure systems are not covered by this document.
Methods of trenchless construction include:
-   manned and unmanned techniques;
-   steerable and non-steerable techniques.
Mining or tunnelling (e.g. in situ construction or the use of prefabricated segments) are not covered by this document although some parts may apply to these methods.
Requirements for associated pipeline installation work other than trenchless construction, e.g. for manholes and inspection chambers, are not covered by this document and are specified in EN 1610. This also applies to pipes that are subsequently installed within entry and exit shafts/pits.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1253-7:2023(Main)
Gullies for buildings - Part 7: Trapped floor gullies with mechanical closure
EN 1253-7:2022

This document classifies floor gullies for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with a mechanical closure (referred to as floor gullies).
Note: Floor gullies with a mechanical closure are not covered by Part 1, Part 6, Part 8.
These products are intended to be installed where:
- the building does not exceed a ground-floor and three floors above;
- infrequent use could result in a water seal evaporating.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1253-8:2023(Main)
Gullies for buildings - Part 8: Trapped floor gullies with combined mechanical closure and water seal
EN 1253-8:2022

This document classifies floor gullies for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with combined mechanical closure and water seal (referred to as floor gullies).
Note: Floor gullies with combined mechanical closure and water seal are not covered by Part 1, Part 6, Part 7.
These products are intended to be installed where:
- the building does not exceed a ground-floor and three floors above.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 11296-9:2023(Main)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 9: Lining with a rigidly anchored plastics inner layer (ISO 11296-9:2022)
EN ISO 11296-9:2022

This document, in conjunction with EN ISO 11296-1, specifies requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout.
This document is applicable to plastics inner layers and grout systems with or without steel reinforcement.
It does not apply to the structural design of the lining system.
NOTE Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this Standard.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1253-6:2023(Main)
Gullies for buildings - Part 6: Trapped floor gullies with a depth of water seal less than 50 mm
EN 1253-6:2022

This document classifies floor gullies for use inside buildings, gives guidance for places of installation and specifies requirements for the construction, design, performance and marking of factory made gullies for buildings, irrespective of the material, for use in drainage systems requiring a trap with a depth of water seal of less than 50 mm (referred to as floor gullies).
Note: Floor gullies with a depth water seal of less than 50 mm are not covered by Part 1, Part 7, Part 8.
These products are intended to be installed only where:
- space limitation will not accommodate a gully with a 50 mm water seal;
- the building does not exceed a ground-floor and three floors above;
- at least two sanitary appliances are installed in addition to the gully but with only one toilet on the same branch (connection pipe);
- or secondary or branch ventilation is installed according to clauses 4.3.2 or 4.3.4 of EN 12056-2.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 16933-1:2022(Main)
Drain and sewer systems outside buildings - Design - Part 1: Layout principles
EN 16933-1:2022

This document specifies requirements for the design of drain and sewer systems outside buildings.
It is applicable to drain and sewer systems, which operate essentially under gravity, from the point where the wastewater leaves a building, roof drainage system, or paved area, to a point where it is discharged into a wastewater treatment plant or receiving water body.
This part specifies requirements for the layout of drain and sewer systems.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 17426:2019(Main)
Sanitary appliances - Drainage systems for the application of sanitary appliances
CEN/TR 17426:2019

This document describes the installation rules that must be followed to ensure proper functioning of the drainage system depending on the specified performance of the sanitary appliances.
These performance characteristics of sanitary appliances (defined in the harmonized standards EN 997, EN 13407, EN 14688, EN 14528 and EN 14527) are explained and brought into line with the application rules of standard series EN 12056.
According to Regulation (EU) 305/2011, legally binding information on building requirements must be provided by the National Product Information Point. Therefore, additional national requirements are mentioned informatively where information is available.

  • Technical report
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15885:2019(Main)
Classification and characteristics of techniques for renovation, repair and replacement of drains and sewers
EN 15885:2018

This European Standard specifies a system for the classification of trenchless techniques for renovation, repair and replacement on the same line of drains and sewers outside buildings, operated under gravity or pressure, including pipes, connections and manholes. It defines and describes families of techniques and their different generic methods and materials used.
This European Standard does not apply for replacement by open trenching according to EN 1610 and trenchless construction and testing of drains and sewers as new construction off-the-line of the existing drain or sewer according to EN 12889.
This European Standard does not apply for the specification of requirements for specific products.
For each technique family it lists relevant existing standards, materials and applications and outlines characteristics including installation aspects, structural and hydraulic capabilities and site impact.
This standard does not apply to any work required on the existing pipe prior to renovation, repair or replacement.
This European Standard provides information needed to determine viable options for identification of the optimal technique with regard to a given set of renovation, repair or replacement objectives.
NOTE   It is the responsibility of the designer to choose and design the renovation and repair systems.
It does not specify the calculation methods to determine, for each viable technique, the required amount of material needed to secure the desired performance of the pipeline to be rehabilitated.

  • Standard
    53 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1253-5:2017(Main)
Gullies for buildings - Part 5: Gullies with light liquids closure
EN 1253-5:2017

This draft European Standard specifies requirements for the design, construction, performance, application and marking as well as test methods of factory made gullies with a light liquid closure for buildings.
Light liquid closures for buildings shall be applied to avoid uncontrolled discharge of light liquids into drainage systems in case of emergency.
This draft European Standard does not apply to installations for separation of light liquids covered by EN 858-1.

  • Standard
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1253-4:2016(Main)
Gullies for buildings - Part 4: Access covers
EN 1253-4:2016

This draft European Standard classifies access covers according to their loading strength and specifies requirements relating to their design, construction, marking, testing and evaluation of conformity.
This draft European Standard classifies and specifies requirements for factory made access covers used for drainage systems inside buildings. This draft standard does not apply to access covers intended for external use which are covered by EN 124 series.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day