SIST EN ISO 3369:2010
(Main)Impermeable sintered metal materials and hardmetals - Determination of density (ISO 3369:2006)
Impermeable sintered metal materials and hardmetals - Determination of density (ISO 3369:2006)
This International Standard specifies a method of determining the density of impermeable sintered metal materials and hardmetals.
Undurchlässige Sintermetallwerkstoffe und Hartmetalle - Ermittlung der Dichte (ISO 3369:2006)
Diese Internationale Norm legt ein Verfahren zur Ermittlung der Dichte von undurchlässigen Sintermetallen und Hartmetallen fest.
ANMERKUNG Für die Ermittlung der Dichte von durchlässigen Sintermetallen, siehe ISO 2738:1999, Sintered metal materials, excluding hardmetals -— Permeable sintered metal materials -— Determination of density, oil content and open porosity
Matériaux en métal fritté imperméable et métaux-durs - Détermination de la masse volumique (ISO 3369:2006)
L'ISO 3369:2006 spécifie une méthode de détermination de la masse volumique des matériaux en métal fritté imperméable et des métaux-durs.
Neprepustne sintrane kovine in trdine - Določevanje gostote (ISO 3369:2006)
Ta mednarodni standard določa metodo določanja gostote neprepustnih sintranih kovin in trdin.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 3369:2010
01-julij-2010
1DGRPHãþD
SIST EN 23369:2000
1HSUHSXVWQHVLQWUDQHNRYLQHLQWUGLQH'RORþHYDQMHJRVWRWH ,62
Impermeable sintered metal materials and hardmetals - Determination of density (ISO
3369:2006)
Undurchlässige Sintermetallwerkstoffe und Hartmetalle - Ermittlung der Dichte (ISO
3369:2006)
Matériaux en métal fritté imperméable et métaux-durs - Détermination de la masse
volumique (ISO 3369:2006)
Ta slovenski standard je istoveten z: EN ISO 3369:2010
ICS:
77.160 Metalurgija prahov Powder metallurgy
SIST EN ISO 3369:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 3369:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 3369:2010
EUROPEAN STANDARD
EN ISO 3369
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2010
ICS 77.160 Supersedes EN 23369:1993
English Version
Impermeable sintered metal materials and hardmetals -
Determination of density (ISO 3369:2006)
Matériaux en métal fritté imperméable et métaux-durs - Undurchlässige Sintermetallwerkstoffe und Hartmetalle -
Détermination de la masse volumique (ISO 3369:2006) Ermittlung der Dichte (ISO 3369:2006)
This European Standard was approved by CEN on 16 April 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3369:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 3369:2010
EN ISO 3369:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 3369:2010
EN ISO 3369:2010 (E)
Foreword
The text of ISO 3369:2006 has been prepared by Technical Committee ISO/TC 119 “Powder metallurgy” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 3369:2010.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2010, and conflicting national standards shall be withdrawn at
the latest by October 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 23369:1993.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 3369:2006 has been approved by CEN as a EN ISO 3369:2010 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 3369:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 3369:2010
INTERNATIONAL ISO
STANDARD 3369
Second edition
2006-11-15
Impermeable sintered metal materials
and hardmetals — Determination of
density
Matériaux en métal fritté imperméable et métaux-durs — Détermination
de la masse volumique
Reference number
ISO 3369:2006(E)
©
ISO 2006
---------------------- Page: 7 ----------------------
SIST EN ISO 3369:2010
ISO 3369:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 3369:2010
ISO 3369:2006(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Principle. 1
4 Apparatus and materials. 1
5 Test piece . 2
6 Procedure . 2
7 Expression of results . 3
8 Test report . 3
9 Precision statement (Statement of accuracy). 3
© ISO 2006 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Undurchlässige Sintermetallwerkstoffe und Hartmetalle - Ermittlung der Dichte (ISO 3369:2006)Matériaux en métal fritté imperméable et métaux-durs - Détermination de la masse volumique (ISO 3369:2006)Impermeable sintered metal materials and hardmetals - Determination of density (ISO 3369:2006)77.160Metalurgija prahovPowder metallurgyICS:Ta slovenski standard je istoveten z:FprEN ISO 3369kSIST FprEN ISO 3369:2010en,fr,de01-januar-2010kSIST FprEN ISO 3369:2010SLOVENSKI
STANDARD
kSIST FprEN ISO 3369:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 3369
October 2009 ICS 77.160 Will supersede EN 23369:1993English Version
Impermeable sintered metal materials and hardmetals - Determination of density (ISO 3369:2006)
Matériaux en métal fritté imperméable et métaux-durs - Détermination de la masse volumique (ISO 3369:2006)
Undurchlässige Sintermetallwerkstoffe und Hartmetalle - Ermittlung der Dichte (ISO 3369:2006) This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/SS M11.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2009 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 3369:2009: EkSIST FprEN ISO 3369:2010
FprEN ISO 3369:2009 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 3369:2010
FprEN ISO 3369:2009 (E) 3 Foreword The text of ISO 3369:2006 has been prepared by Technical Committee ISO/TC 119 “Powder metallurgy” of the International Organization for Standardization (ISO) and has been taken over as FprEN ISO 3369:2009. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN 23369:1993. Endorsement notice The text of ISO 3369:2006 has been approved by CEN as a FprEN ISO 3369:2009 without any modification.
kSIST FprEN ISO 3369:2010
kSIST FprEN ISO 3369:2010
Reference numberISO 3369:2006(E)© ISO 2006
INTERNATIONAL STANDARD ISO3369Second edition2006-11-15Impermeable sintered metal materials and hardmetals — Determination of density Matériaux en métal fritté imperméable et métaux-durs — Détermination de la masse volumique
kSIST FprEN ISO 3369:2010
ISO 3369:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii © ISO 2006 – All rights reserved
kSIST FprEN ISO 3369:2010
ISO 3369:2006(E) © ISO 2006 – All rights reserved iiiContents Page Foreword.iv 1 Scope.1 2 Normative references.1 3 Principle.1 4 Apparatus and materials.1 5 Test piece.2 6 Procedure.2 7 Expression of results.3 8 Test report.3 9 Precision statement (Statement of accuracy).3
kSIST FprEN ISO 3369:2010
ISO 3369:2006(E) iv © ISO 2006 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-gov
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.