SIST EN ISO 15526-1:2004

Plastics - Polyketone (PK) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 15526-1:2000)

Kunststoffe - Polyketon(PK)-Formmassen - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 15526-1:2000)

1.1   Dieser Teil von prEN ISO 15526 legt ein Bezeichnungssystem für thermoplastische PK-Massen fest, das als Grundlage für Spezifikationen verwendet kann. PK-Polymerketten sind aus sich regelmäßig abwechselnden Olefineinheiten und Ketogruppen aufgebaut. Die Olefineinheiten können im Prinzip ausnahmslos Ethylen oder z. B. nach dem Zufallsprinzip verteiltes Ethylen, Propylen, Buten oder Hexen sein.
1.2   Die Arten der Polyketonkunststoffe werden mit Hilfe eines Einteilungssystem voneinander unterschieden, das auf geeigneten Wertebereichen der folgenden kennzeichnenden Eigenschaften:
a)   Schmelztemperatur;
b)   Schmelze-Volumenfließrate;
c)   Verformungstemperatur unter Last;
und auf Angaben über Zusammensetzung, vorgesehene Verwendung und/oder Verarbeitungsverfahren, wichtige Eigenschaften, Additive, Farbstoffe, Füll- und Verstärkungsstoffe beruht.
1.3   Dieser Teil von EN ISO 15526 gilt für nicht modifizierte gebrauchsfertige Werkstoffe in Form von Pulver, Granulat oder Pellets und für Formmassen, die mit Farbstoffen, Additiven, Füllstoffen usw. modifiziert wurden.
1.4   Es soll nicht behauptet werden, dass Formmassen mit gleicher Bezeichnung zwangsläufig Gleiches leisten. Dieser Teil von ISO 15526 enthält keine technischen Daten, Leistungsangaben oder Verarbeitungsbedingungen, die erforderlich sein können, um eine Formmasse für eine spezielle Anwendung und/oder ein bestimmtes Verarbeitungsverfahren zu spezifizieren.
Wenn derartige zusätzliche Eigenschaften gefragt sind, müssen sie, soweit möglich, nach den in ISO 15526-2 festgelegten Prüfverfahren bestimmt werden.
1.5   Um eine thermoplastische Formmasse für eine bestimmte Anwendung zu spezifizieren oder eine reproduzierbare Verarbeitung sicherzustellen, können im Daten-Block 5 (siehe 3.1) zusätzliche Anforderungen angegeben werden.

Plastiques - Polycétone (PK) pour moulage et extrusion - Partie 1: Systeme de désignation et base de spécification (ISO 15526-1:2000)

Polimerni materiali - Materiali za oblikovanje in ekstrudiranje na osnovi poliketonov (PK) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 15526-1:2000)

General Information

• Status: Withdrawn
• Publication Date: 30-Sep-2004
• Withdrawal Date: 25-Mar-2014
• ICS: 83.080.20 - Thermoplastic materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 25-Mar-2014
• Due Date: 17-Apr-2014
• Completion Date: 26-Mar-2014
• Ref Project: EN ISO 15526-1:2004 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 15526-1:2000)

Relations

• Replaced By: SIST EN ISO 21970-1:2018 - Plastics - Polyketone (PK) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 21970-1:2018)
• Effective Date: 20-Feb-2019

Standards Content (Sample)

SLOVENSKI STANDARD
01-oktober-2004
3ROLPHUQLPDWHULDOL0DWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMHQDRVQRYL
SROLNHWRQRY3.GHO6LVWHPR]QDþHYDQMDLQSRGODJH]DVSHFLILNDFLMH,62

Plastics - Polyketone (PK) moulding and extrusion materials - Part 1: Designation system
and basis for specifications (ISO 15526-1:2000)
Kunststoffe - Polyketon(PK)-Formmassen - Teil 1: Bezeichnungssystem und Basis für
Spezifikationen (ISO 15526-1:2000)
Plastiques - Polycétone (PK) pour moulage et extrusion - Partie 1: Systeme de
désignation et base de spécification (ISO 15526-1:2000)
Ta slovenski standard je istoveten z: EN ISO 15526-1:2004
ICS:
83.080.20 Plastomeri Thermoplastic materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 15526-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2004
ICS 83.080.20
English version
Plastics - Polyketone (PK) moulding and extrusion materials -
Part 1: Designation system and basis for specifications (ISO
15526-1:2000)
Plastiques - Polycétone (PK) pour moulage et extrusion -
Partie 1: Système de désignation et base de spécification
(ISO 15526-1:2000)
This European Standard was approved by CEN on 21 June 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15526-1:2004: E
worldwide for CEN national Members.

Foreword
The text of ISO 15526-1:2000 has been prepared by Technical Committee ISO/TC 61 "Plastics”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO
15526-1:2004 by Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held
by IBN.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by January 2005, and conflicting national
standards shall be withdrawn at the latest by January 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Endorsement notice
The text of ISO 15526-1:2000 has been approved by CEN as EN ISO 15526-1:2004 without any
modifications.
NOTE Normative references to International Standards are listed in Annex ZA (normative).

Annex ZA
(normative)
Normative references to international publications
with their relevant European publications

This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).

NOTE Where an International Publication has been modified by common modifications, indicated
by (mod.), the relevant EN/HD applies.

Publication Year Title EN Year

ISO 1043-1 2001 Plastics - Symbols and abbreviated EN ISO 1043-1 2001
terms - Part 1: Basic polymers and
their special characteristics
ISO 1043-2 2000 Plastics - Symbols and abbreviated EN ISO 1043-2 2001
terms - Part 2: Fillers and reinforcing
materials
INTERNATIONAL ISO
STANDARD 15526-1
First edition
2000-06-01
Plastics — Polyketone (PK) moulding and
extrusion materials —
Part 1:
Designation system and basis for
specifications
Plastiques — Polycétone (PK) pour moulage et extrusion —
Partie 1: Système de désignation et base de spécification
Reference number
ISO 15526-1:2000(E)
ISO 15526-1:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be
edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file,
parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, elec-
tronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's mem-
ber body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail [e-mail]
Web www.iso.ch
Printed in Switzerland
©
ii ISO 2000 – All rights reserved

ISO 15526-1:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commis-
sion (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 15526 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 15526-1 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee
SC 9, Thermoplastic materials.
ISO 15526 consists of the following parts, under the general title Plastics — Polyketone (PK) moulding and extrusion
materials:
— Part 1: Designation system and basis for specifications
— Part 2: Preparation of test specimens and determination of properties
©
ISO 2000 – All rights reserved iii

INTERNATIONAL STANDARD ISO 15526-1:2000(E)
Plastics — Polyketone (PK) moulding and extrusion materials —
Part 1:
Designation system and basis for specifications
1 Scope
1.1 This part of ISO 15526 establishes a system of designation for PK thermoplastic material which may be used
as the basis for specifications. PK polymer chains are built up from regularly alternating olefinic units and keto
groups. The olefinic units may be essentially all ethylene, or they may be, e.g., randomly distributed ethylene and pro-
pylene, butene or hexene.
1.2 The types of polyketone plastics are differentiated from each other by a classification system based on
appropriate levels of the designatory properties
a) melting temperature
b) melt volume-flow rate
c) temperature of deflection under load
and on information about basic polymer parameters, intended application and/or method of processing, important
properties, additives, colorants, fillers and reinforcing materials.
1.3 This part of ISO 15526 applies to materials ready for normal use in the form of powder, granules or pellets and
to materials unmodified or modified by colorants, additives, fillers, etc.
1.4 It is not intended to imply that materials having the same designation give necessarily the same performance.
This part of ISO 15526 does not provide engineering data, performance data or data on processing conditions which
may be required to specify a material for a particular application and/or method of processing.
If such additional properties are required, they shall be determined in accordance with the test methods specified in
ISO 15526-2, if suitable.
1.5 In order to specify a thermoplastic material for a particular application or to ensure reproducible processing,
additional requirements may be given in data block 5 (see 3.1).
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 15526. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 15526 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated references,
the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of
currently valid International Standards.
ISO 1043-1, Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics.
ISO 1043-2, Plastics — Symbols and abbreviated terms — Part 2: Fillers and reinforcing materials.
ISO 15526-2, Plastics — Polyketone (PK) moulding and extrusion materials — Part 2: Preparation of test specimens
and determination of properties.
©
ISO 2000 – All rights reserved 1

ISO 15526-1:2000(E)
3 Designation system
3.1 General
The designation system for thermoplastics is based on the following standardized pattern:
Designation
Identity block
International Individual-item block
Description block
Standard
(optional)
Data Data Data Data Data
number
block block block block block
block
1 2 3 4 5
The designation consists of an optional description block, reading “Thermoplastics”, and an identity block comprising
the International Standard number and an individual-item block. For unambiguous coding, the individual-item block is
subdivided into 5 data blocks comprising the following information:
— Data block 1: Identification of the plastic by its symbol PK in accordance with ISO 1043-1 and information about
the composition of the polymer (see 3.2).
— Data block 2: Position 1: intended application or method of processing (see 3.3).
Positions 2 to 8: important properties, additives and supplementary information (see 3.3).
— Data block 3: Designatory properties (see 3.4).
— Data block 4: Fillers or reinforcing materials and their nominal content (see 3.5).
— Data block 5: For the purpose of specifications, a fifth data block may be added containing additional infor-
mation.
The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other
by commas.
If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,,).
3.2 Data block 1
In this data block, after the hyphen, polyketone plastics are identified by the symbol PK, in accordance with
ISO 1043-1, followed by a hyphen and 1 or 2 code-letters stating the olefinic units in the chain, as specified in
Table 1.
Table 1 — Code-letters used in data block 1 for giving additional
information on the composition
Code-letter Formula
–[CO–C H]–[CO–C H R] –
mn
2 4 2 3
in which the two types of olefinic group are distributed
randomly throughout the molecule
E R=H
EP R=CH
EB R=C H
2 5
EH R=C H
4 9
©
2 ISO 2000 – All rights reserved

ISO 15526-1:2000(E)
3.3 Data block 2
In this data block, information about intended application and/or method of processing is given in position 1 and infor-
mation about important properties, additives and colour in positions 2 to 8. The code-letters used are specified in Ta-
ble 2.
If information is presented in positions 2 to 8 and no specific information is given in position 1, the letter X shall be
inserted in position 1.
Table 2 — Code-letters used in data block 2
Code-letter Position 1 Code-letter Positions 2 to 8
A Adhesives A Processing stabilized
B Blow moulding B Antiblocking
C Calendering C Coloured
D Powder
E Extrusion E Expandable
F Extrusion of films F Special burning characteristics
G General use G Gra
...