SIST ISO 12643-1:2008
(Main)Graphic technology - Safety requirements for graphic technology equipment and systems - Part 1: General requirements
Graphic technology - Safety requirements for graphic technology equipment and systems - Part 1: General requirements
ISO 12643-1:2007 provides safety specifications for the design and construction of new machines used in printing press systems and in binding and finishing systems. It includes equipment used in a stand-alone mode, or in combination with other machines, including ancillary equipment, in which all the machine actuators (e.g. drives) of the equipment are controlled by the same control system.
The requirements listed in ISO 12643-1:2007 are applicable to the equipment covered by all parts of ISO 12643, unless otherwise noted. Requirements specific to press and binding and finishing equipment and systems, that are not included in ISO 12643-1:2007, are given in ISO 12643-2 and ISO 12643-3, respectively.
ISO 12643-1:2007 addresses recognized hazards specific to equipment and systems in the following areas:
mechanical;
electrical;
slipping, tripping, falling;
ergonomics;
noise;
radiation;
fire and explosion;
thermal;
other emissions.
It is advisable that technologies not identified in ISO 12643-1:2007 incorporate the safety principles set forth herein in their design.
Technologie graphique — Exigences de sécurité pour les systèmes et l'équipement de technologie graphique — Partie 1: Exigences générales
Grafična tehnologija – Varnostne zahteve za grafično tehnološko opremo in sisteme – 1. del: Splošne zahteve
General Information
Relations
Standards Content (Sample)
INTERNATIONAL ISO
STANDARD 12643-1
First edition
2007-03-01
Graphic technology — Safety
requirements for graphic technology
equipment and systems —
Part 1:
General requirements
Technologie graphique — Exigences de sécurité pour les systèmes et
l'équipement de technologie graphique —
Partie 1: Exigences générales
Reference number
©
ISO 2007
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions. 4
4 Effective date. 11
5 Guarding of significant hazards. 11
6 Requirements for protection against other hazards . 30
7 Release from hazardous situation . 42
8 Control zones . 42
9 Controls . 43
10 Control stations . 53
11 Control systems. 58
12 Ergonomics and labelling of indicators and actuators. 60
13 Signals and warning devices. 60
14 Warning signs and labels . 63
15 Contents of instruction handbook. 64
Annex A (informative) Risk analysis relating to the pitch angle of access stairs . 67
Annex B (informative) Noise . 69
Annex C (normative) Area warning light system . 71
Annex D (informative) Example layout of instruction handbooks . 73
Bibliography . 75
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12643-1 was prepared by Technical Committee ISO/TC 130, Graphic technology.
This first edition of ISO 12643-1, together with ISO 12643-2, cancels and replaces ISO 12648:2006, which
has been technically revised. This edition of ISO 12643-1, together with ISO 12643-3, cancels and replaces
ISO 12649:2004, which has been technically revised.
ISO 12643 consists of the following parts, under the general title Graphic technology — Safety requirements
for graphic technology equipment and systems:
⎯ Part 1: General requirements
⎯ Part 2: Press equipment and systems
⎯ Part 3: Binding and finishing equipment
iv © ISO 2007 – All rights reserved
Introduction
During the development of this part of ISO 12643, existing relevant standards of other countries were taken
into consideration. An effort has been made to take into consideration the requirements of many countries,
recognizing that national standards or laws may dictate national requirements. In cases where it was known
that there is a national requirement that differs from this part of ISO 12643, that has been noted.
This part of ISO 12643 was developed to harmonize the following U.S. and European safety standards:
⎯ ANSI B65.1, Graphic technology — Safety standard — Printing press systems;
⎯ ANSI B65.2, Binding and Finishing Systems;
⎯ ANSI B65.3, Safety standard — Guillotine paper cutters, mill trimmers, and integral handling equipment;
⎯ ANSI B65.4, Safety standard — Three-knife trimmers, including rotary, and single- and multiple-knife
trimmers;
⎯ EN 1010-1, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 1: Common requirements;
⎯ EN 1010-2, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 2: Printing and varnishing machines including pre-press machinery;
⎯ EN 1010-3, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 3: Cutting machines;
⎯ EN 1010-4, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 4: Bookbinding, paper converting and finishing machines.
INTERNATIONAL STANDARD ISO 12643-1:2007(E)
Graphic technology — Safety requirements for graphic
technology equipment and systems —
Part 1:
General requirements
1 Scope
This part of ISO 12643 provides safety specifications for the design and construction of new machines used in
printing press systems and in binding and finishing systems. It includes equipment used in a stand-alone
mode, or in combination with other machines, including ancillary equipment, in which all the machine
actuators (e.g. drives) of the equipment are controlled by the same control system.
The requirements listed in this part of ISO 12643 are applicable to the equipment covered by all parts of
ISO 12643, unless otherwise noted. Requirements specific to press and binding and finishing equipment and
systems, that are not included in this part of ISO 12643, are given in ISO 12643-2 and ISO 12643-3,
respectively.
This part of ISO 12643 addresses recognized hazards specific to equipment and systems in the following
areas:
⎯ mechanical;
⎯ electrical;
⎯ slipping, tripping, falling;
⎯ ergonomics;
⎯ noise;
⎯ radiation;
⎯ fire and explosion;
⎯ thermal;
⎯ other emissions.
It is advisable that technologies not identified in this part of ISO 12643 incorporate the safety principles set
forth herein in their design.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 8031, Rubber and plastic hoses and hose assemblies — Determination of electrical resistance
ISO 11553-1, Safety of machinery — Laser processing machines — Part 1: General safety requirements
ISO/TR 11688-1, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning
ISO 11689, Acoustics — Procedure for the comparison of noise-emission data for machinery and equipment
ISO 12100-1, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology
ISO 12100-2, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical
principles
ISO 12643-2:2007, Graphic technology — Safety requirements for graphic technology equipment and sys-
tems — Part 2: Press equipment and systems
1)
ISO 12643-3:— , Graphic technology — Safety requirements for graphic technology equipment and sys-
tems — Part 3: Binding and finishing equipment
ISO 13732-1, Ergonomics of the thermal environment — Methods for the assessment of human responses to
contact with surfaces — Part 1: Hot surfaces
ISO 13849-1:1999, Safety of machinery — Safety-related parts of control systems — Part 1: General
principles for design
ISO 13850, Safety of machinery — Emergency stop — Principles for design
ISO 13851, Safety of machinery — Two-hand control devices — Functional aspects and design principles
ISO 13852, Safety of machinery — Safety distances to prevent danger zones being reached by the upper
limbs
ISO 13854, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body
ISO 13855, Safety of machinery — Positioning of protective equipment with respect to the approach speeds of
parts of the human body
ISO 13856-1, Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for
design and testing of pressure-sensitive mats and pressure-sensitive floors
ISO 14119:1998, Safety of machinery — Interlocking devices associated with guards — Principles for design
and selection
ISO 14120, Safety of machinery — Guards — General requirements for the design and construction of fixed
and movable guards
1) To be published.
2 © ISO 2007 – All rights reserved
ISO 14122-1, Safety of machinery — Permanent means of access to machinery — Part 1: Choice of a fixed
means of access between two levels
ISO 14122-2, Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms
and walkways
ISO 14122-3, Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders
and guard-rails
2)
ISO/TR 15847:— , Graphic technology — Graphical symbols for printing press systems and finishing sys-
tems, including related auxiliary equipment
IEC 60079-1, Electrical apparatus for explosive gas atmospheres — Part 1: Flameproof enclosures “d”
IEC 60079-2, Electrical apparatus for explosive gas atmospheres — Part 2: Pressurized enclosures “p”
IEC 60079-5, Electrical apparatus for explosive gas atmospheres — Part 5: Powder filling “q”
IEC 60079-6, Electrical apparatus for explosive gas atmospheres — Part 6: Oil-immersion “o”
IEC 60079-7, Explosive atmospheres — Part 7: Equipment protection by increased safety “e”
IEC 60079-11, Explosive atmospheres — Part 11: Equipment protection by intrinsic safety “i”
IEC 60079-14, Electrical apparatus for explosive gas atmospheres — Part 14: Electrical installations in
hazardous areas (other than mines)
IEC 60079-18, Electrical apparatus for explosive gas atmospheres — Part 18: Construction, test and marking
of type of protection encapsulation “m” electrical apparatus
IEC 60204-1, Safety of machinery — Electrical equipment of machines — Part 1: General requirements
IEC 60825-1, Safety of laser products — Part 1: Equipment classification, requirements and user’s guide
IEC 60947-2, Low-voltage switchgear and controlgear — Part 2: Circuit-breakers
IEC 60947-3, Low-voltage switchgear and controlgear — Part 3: Switches, disconnectors, switch-
disconnectors and fuse-combination
...
SLOVENSKI STANDARD
01-januar-2008
*UDILþQDWHKQRORJLMD±9DUQRVWQH]DKWHYH]DJUDILþQRWHKQRORãNRRSUHPRLQ
VLVWHPH±GHO 6SORãQH]DKWHYH
Graphic technology - Safety requirements for graphic technology equipment and
systems - Part 1: General requirements
Ta slovenski standard je istoveten z:
ICS:
37.100.10 Reprodukcijska oprema Reproduction equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 12643-1
First edition
2007-03-01
Graphic technology — Safety
requirements for graphic technology
equipment and systems —
Part 1:
General requirements
Technologie graphique — Exigences de sécurité pour les systèmes et
l'équipement de technologie graphique —
Partie 1: Exigences générales
Reference number
©
ISO 2007
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 2
3 Terms and definitions. 4
4 Effective date. 11
5 Guarding of significant hazards. 11
6 Requirements for protection against other hazards . 30
7 Release from hazardous situation . 42
8 Control zones . 42
9 Controls . 43
10 Control stations . 53
11 Control systems. 58
12 Ergonomics and labelling of indicators and actuators. 60
13 Signals and warning devices. 60
14 Warning signs and labels . 63
15 Contents of instruction handbook. 64
Annex A (informative) Risk analysis relating to the pitch angle of access stairs . 67
Annex B (informative) Noise . 69
Annex C (normative) Area warning light system . 71
Annex D (informative) Example layout of instruction handbooks . 73
Bibliography . 75
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 12643-1 was prepared by Technical Committee ISO/TC 130, Graphic technology.
This first edition of ISO 12643-1, together with ISO 12643-2, cancels and replaces ISO 12648:2006, which
has been technically revised. This edition of ISO 12643-1, together with ISO 12643-3, cancels and replaces
ISO 12649:2004, which has been technically revised.
ISO 12643 consists of the following parts, under the general title Graphic technology — Safety requirements
for graphic technology equipment and systems:
⎯ Part 1: General requirements
⎯ Part 2: Press equipment and systems
⎯ Part 3: Binding and finishing equipment
iv © ISO 2007 – All rights reserved
Introduction
During the development of this part of ISO 12643, existing relevant standards of other countries were taken
into consideration. An effort has been made to take into consideration the requirements of many countries,
recognizing that national standards or laws may dictate national requirements. In cases where it was known
that there is a national requirement that differs from this part of ISO 12643, that has been noted.
This part of ISO 12643 was developed to harmonize the following U.S. and European safety standards:
⎯ ANSI B65.1, Graphic technology — Safety standard — Printing press systems;
⎯ ANSI B65.2, Binding and Finishing Systems;
⎯ ANSI B65.3, Safety standard — Guillotine paper cutters, mill trimmers, and integral handling equipment;
⎯ ANSI B65.4, Safety standard — Three-knife trimmers, including rotary, and single- and multiple-knife
trimmers;
⎯ EN 1010-1, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 1: Common requirements;
⎯ EN 1010-2, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 2: Printing and varnishing machines including pre-press machinery;
⎯ EN 1010-3, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 3: Cutting machines;
⎯ EN 1010-4, Safety of machinery — Safety requirements for the design and construction of printing and
paper converting machines — Part 4: Bookbinding, paper converting and finishing machines.
INTERNATIONAL STANDARD ISO 12643-1:2007(E)
Graphic technology — Safety requirements for graphic
technology equipment and systems —
Part 1:
General requirements
1 Scope
This part of ISO 12643 provides safety specifications for the design and construction of new machines used in
printing press systems and in binding and finishing systems. It includes equipment used in a stand-alone
mode, or in combination with other machines, including ancillary equipment, in which all the machine
actuators (e.g. drives) of the equipment are controlled by the same control system.
The requirements listed in this part of ISO 12643 are applicable to the equipment covered by all parts of
ISO 12643, unless otherwise noted. Requirements specific to press and binding and finishing equipment and
systems, that are not included in this part of ISO 12643, are given in ISO 12643-2 and ISO 12643-3,
respectively.
This part of ISO 12643 addresses recognized hazards specific to equipment and systems in the following
areas:
⎯ mechanical;
⎯ electrical;
⎯ slipping, tripping, falling;
⎯ ergonomics;
⎯ noise;
⎯ radiation;
⎯ fire and explosion;
⎯ thermal;
⎯ other emissions.
It is advisable that technologies not identified in this part of ISO 12643 incorporate the safety principles set
forth herein in their design.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 8031, Rubber and plastic hoses and hose assemblies — Determination of electrical resistance
ISO 11553-1, Safety of machinery — Laser processing machines — Part 1: General safety requirements
ISO/TR 11688-1, Acoustics — Recommended practice for the design of low-noise machinery and
equipment — Part 1: Planning
ISO 11689, Acoustics — Procedure for the comparison of noise-emission data for machinery and equipment
ISO 12100-1, Safety of machinery — Basic concepts, general principles for design — Part 1: Basic
terminology, methodology
ISO 12100-2, Safety of machinery — Basic concepts, general principles for design — Part 2: Technical
principles
ISO 12643-2:2007, Graphic technology — Safety requirements for graphic technology equipment and sys-
tems — Part 2: Press equipment and systems
1)
ISO 12643-3:— , Graphic technology — Safety requirements for graphic technology equipment and sys-
tems — Part 3: Binding and finishing equipment
ISO 13732-1, Ergonomics of the thermal environment — Methods for the assessment of human responses to
contact with surfaces — Part 1: Hot surfaces
ISO 13849-1:1999, Safety of machinery — Safety-related parts of control systems — Part 1: General
principles for design
ISO 13850, Safety of machinery — Emergency stop — Principles for design
ISO 13851, Safety of machinery — Two-hand control devices — Functional aspects and design principles
ISO 13852, Safety of machinery — Safety distances to prevent danger zones being reached by the upper
limbs
ISO 13854, Safety of machinery — Minimum gaps to avoid crushing of parts of the human body
ISO 13855, Safety of machinery — Positioning of protective equipment with respect to the approach speeds of
parts of the human body
ISO 13856-1, Safety of machinery — Pressure-sensitive protective devices — Part 1: General principles for
design and testing of pressure-sensitive mats and pressure-sensitive floors
ISO 14119:1998, Safety of machinery — Interlocking devices associated with guards — Principles for design
and selection
ISO 14120, Safety of machinery — Guards — General requirements for the design and construction of fixed
and movable guards
1) To be published.
2 © ISO 2007 – All rights reserved
ISO 14122-1, Safety of machinery — Permanent means of access to machinery — Part 1: Choice of a fixed
means of access between two levels
ISO 14122-2, Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms
and walkways
ISO 14122-3, Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders
and guard-rails
2)
ISO/TR 15847:— , Graphic technology — Graphical symbols for printing press systems and finishing sys-
tems, including related auxiliary equipment
IEC 60079-1, Electrical apparatus for explosive gas atmospheres — Part 1: Flameproof enclosures “d”
IEC 60079-2, Electrical apparatus for explosive gas atmospheres — Part 2: Pressurized enclosures “p”
IEC 60079-5, Electrical apparatus for explosive gas atmospheres — Part 5: Powder filling “q”
IEC 60079-6, Electrical apparatus for explosive gas atmospheres — Part 6: Oil-immersion “o”
IEC 60079-7, Explosive atmospheres — Part 7: Equipment protection by increased safety “e”
IEC 60079-11, Explosive atmospheres — Part 11: Equipment protection by intrinsic safety “i”
IEC 60079-14, Electrical apparatus for explosive gas atmospheres — Part 14: Electrical installations in
hazardous areas (other than mine
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.