SIST ISO 24487:2024

Graphic technology — Processless lithographic plates — Evaluation methods for characteristics and performance

This document applies to processless lithographic plates and specifies evaluation methods for
lithographic plate characteristics, on-press development performance, usability and print image quality.
It specifies measurement conditions for materials and equipment and provides guidelines for the
selection of suitable processless lithographic plates by a printing organization and requirements for
comparative assessment tests.
The assessment of waterless lithographic plates is out of scope of this document.
NOTE Some of these methods can be used for the evaluation of all classes of lithographic plate.
This document specifies measurement conditions for materials and equipment and provides guidelines
for the selection of suitable processless lithographic plates by a printing organization and requirements
for comparative assessment tests.

Technologie graphique — Plaques lithographiques sans traitement — Méthodes d'évaluation des caractéristiques et des performances

Grafična tehnologija - Ofsetne plošče brez razvijanja - Metode ocenjevanja lastnosti in uporabnosti

Ta dokument se uporablja za ofsetne plošče brez razvijanja in določa metode vrednotenja lastnosti litografskih plošč, zmogljivosti razvijanja v tisku, uporabnosti in kakovosti tiskane slike.
Določa merilne pogoje za materiale in opremo ter zagotavlja smernice za izbiro primernih ofsetnih plošč brez razvijanja s strani tiskarske organizacije in zahteve za primerjalne ocenjevalne preskuse.
Ocenjevanje brezvodnih ofsetnih plošč ne spada na področje uporabe tega dokumenta.
OPOMBA: Nekatere od teh metod se lahko uporabljajo tudi za vrednotenje vseh razredov ofsetnih plošč.
Ta dokument določa merilne pogoje za materiale in opremo in podaja smernice
za izbiro ustreznih ofsetnih plošč brez razvijanja s strani tiskarske organizacije in zahteve
za primerjalne ocenjevalne preskuse.

General Information

• Status: Published
• Publication Date: 31-Jan-2024
• ICS: 37.100.10 - Reproduction equipment
• Technical Committee: GRT - Graphical technology
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 24-Jan-2024
• Due Date: 30-Mar-2024
• Completion Date: 01-Feb-2024
• Ref Project: ISO 24487:2023 - Graphic technology — Processless lithographic plates — Evaluation methods for characteristics and performance

Relations

• Replaces: SIST ISO 24487-1:2023 - Graphic technology — Processless lithographic plates — Part 1: Evaluation methods for characteristics and performance
• Effective Date: 01-Mar-2024

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 24487:2024
01-marec-2024
Nadomešča:
SIST ISO 24487-1:2023
Grafična tehnologija - Ofsetne plošče brez razvijanja - Metode ocenjevanja
lastnosti in uporabnosti
Graphic technology — Processless lithographic plates — Evaluation methods for
characteristics and performance
Technologie graphique — Plaques lithographiques sans traitement — Méthodes
d'évaluation des caractéristiques et des performances
Ta slovenski standard je istoveten z: ISO 24487:2023
ICS:
37.100.10 Reprodukcijska oprema Reproduction equipment
SIST ISO 24487:2024 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 24487:2024

---------------------- Page: 2 ----------------------
SIST ISO 24487:2024
INTERNATIONAL ISO
STANDARD 24487
First edition
2023-12
Graphic technology — Processless
lithographic plates — Evaluation
methods for characteristics and
performance
Technologie graphique — Plaques lithographiques sans traitement —
Méthodes d'évaluation des caractéristiques et des performances
Reference number
ISO 24487:2023(E)
© ISO 2023

---------------------- Page: 3 ----------------------
SIST ISO 24487:2024
ISO 24487:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 24487:2024
ISO 24487:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test procedure .2
4.1 General . 2
4.2 Test environment . 2
4.3 Plate imaging . 3
4.3.1 General . 3
4.3.2 Colour test form . 3
4.3.3 Abrasion and scratch resistance test form . 4
4.3.4 Image visibility test form . 5
4.4 Pre-dampening amount . . 6
4.5 Pre-inking amount .
...

INTERNATIONAL ISO
STANDARD 24487
First edition
2023-12
Graphic technology — Processless
lithographic plates — Evaluation
methods for characteristics and
performance
Technologie graphique — Plaques lithographiques sans traitement —
Méthodes d'évaluation des caractéristiques et des performances
Reference number
ISO 24487:2023(E)
© ISO 2023

---------------------- Page: 1 ----------------------
ISO 24487:2023(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 24487:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test procedure .2
4.1 General . 2
4.2 Test environment . 2
4.3 Plate imaging . 3
4.3.1 General . 3
4.3.2 Colour test form . 3
4.3.3 Abrasion and scratch resistance test form . 4
4.3.4 Image visibility test form . 5
4.4 Pre-dampening amount . . 6
4.5 Pre-inking amount . 6
4.6 Ink selection . 6
4.7 Substrate selection. 7
4.8 Fountain solution . 7
4.9 Press preparation and control .
...

FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 24487
ISO/TC 130
Graphic technology — Processless
Secretariat: SAC
lithographic plates — Evaluation
Voting begins on:
2023-09-14 methods for characteristics and
performance
Voting terminates on:
2023-11-09
Titre manquant
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO/FDIS 24487:2023(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 1 ----------------------
ISO/FDIS 24487:2023(E)
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 24487
ISO/TC 130
Graphic technology — Processless
Secretariat: SAC
lithographic plates — Evaluation
Voting begins on:
methods for characteristics and
performance
Voting terminates on:
Titre manquant
COPYRIGHT PROTECTED DOCUMENT
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
RECIPIENTS OF THIS DRAFT ARE INVITED TO
ISO copyright office
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
CP 401 • Ch. de Blandonnet 8
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
CH-1214 Vernier, Geneva
DOCUMENTATION.
Phone: [phone]
IN ADDITION TO THEIR EVALUATION AS
Reference number
Email: [e-mail]
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/FDIS 24487:2023(E)
Website: www.iso.org
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
Published in Switzerland
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN­
DARDS TO WHICH REFERENCE MAY BE MADE IN
ii
  © ISO 2023 – All rights reserved
NATIONAL REGULATIONS. © ISO 2023

---------------------- Page: 2 ----------------------
ISO/FDIS 24487:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test procedure .2
4.1 General . 2
4.2 Test environment . 2
4.3 Plate imaging . 3
4.3.1 General . 3
4.3.2 Colour test form . 3
4.3.3 Abrasion and scratch resistance test form . 4
4.3.4 Image visibil
...

ISO/TC 130 5001
Date:2023-08-04
ISO/FDIS 24487:2023(E)
ISO TC 130/ WG 4
ISO/TC 130
Secretariat: SAC
Date: 2023-08-30
Graphic technology — Processless lithographic plates —
Evaluation methods for characteristics and performance
Titre manquant
FDIS stage

---------------------- Page: 1 ----------------------
ISO/FDIS 24487:2023(E)
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this
publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical,
including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can
be requested from either ISO at the address below or ISO'sISO’s member body in the country of the requester.
ISO Copyright Officecopyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Email: [e-mail]
E-mail: [e-mail]
Website: www.iso.orgwww.iso.org
Published in Switzerland.
ii © ISO 2022 – All rights reserved
ii © ISO 2023 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/FDIS 24487:2023(E)
Contents
Foreword . vii
Introduction.ix
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test procedure . 2
4.1 General . 2
4.2 Test environment . 3
4.3 Plate imaging . 3
4.3.1 General . 3
4.3.2 Colour test form . 3
4.3.3 Abrasion and scratch resistance test form . 5
4.3.4 Image visibility test form . 5
4.4 Pre-dampening amount . 7
4.5 Pre-inking amount . 7
4.6 Ink selection . 7
4.7 Substrate selection . 8
4.8 Fountain solution . 8
4.9 Press preparation and control . 8
4.9.1 Press preparation print run . 8
4.9.2 Reference printing aim values. 9
4.10 Printing method . 9
4.11 Plate exposure to light .
...