SIST EN 754-3:2008

Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form

This part of EN 754 specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn round bars having diameters in the range from 3 mm up to and including 100 mm.

Aluminium und Aluminiumlegierungen - Gezogene Stangen und Rohre - Teil 3: Rundstangen, Grenzabmaße und Formtoleranzen

Dieses Dokument legt die Grenzabmaße und Formtoleranzen für gezogene Rundstangen aus Aluminium und
Aluminiumlegierungen mit einem Durchmesser von 3 mm bis 100 mm fest.
Die in diesem Dokument verwendeten Bezeichnungen der Werkstoffzustände entsprechen EN 515.

Aluminium et alliages d'aluminium - Barres et tubes étirés - Partie 3: Barres rondes, tolérances sur dimensions et forme

Le présent document spécifie les tolérances sur dimensions et forme des barres rondes étirées en aluminium et alliages d’aluminium de diametre compris entre 3 mm et 100 mm inclus.

Aluminij in aluminijeve zlitine - Hladno vlečene palice/drogovi in cevi - 3. del: Palice z okroglim prerezom, tolerance mer in oblike

General Information

• Status: Published
• Publication Date: 03-Apr-2008
• ICS: 77.150.10 - Aluminium products
• Technical Committee: INEK - Nonferrous metals
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 27-Mar-2008
• Due Date: 01-Jun-2008
• Completion Date: 04-Apr-2008
• Ref Project: EN 754-3:2008 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form

Relations

• Replaces: SIST EN 754-3:1998 - Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form
• Effective Date: 01-May-2008

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and formAluminium et alliages d'aluminium - Barres et tubes étirés - Partie 3: Barres rondes, tolérances sur dimensions et formeAluminium und Aluminiumlegierungen - Gezogene Stangen und Rohre - Teil 3: Rundstangen, Grenzabmaße und FormtoleranzenTa slovenski standard je istoveten z:EN 754-3:2008SIST EN 754-3:2008en,de77.150.10ICS:SIST EN 754-3:19981DGRPHãþDSLOVENSKI
STANDARDSIST EN 754-3:200801-maj-2008







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 754-3March 2008ICS 77.150.10Supersedes EN 754-3:1995
English VersionAluminium and aluminium alloys - Cold drawn rod/bar and tube -Part 3: Round bars, tolerances on dimensions and formAluminium et alliages d'aluminium - Barres et tubes étirés -Partie 3: Barres rondes, tolérances sur dimensions etformeAluminium und Aluminiumlegierungen - Gezogene Stangenund Rohre - Teil 3: Rundstangen, Grenzabmaße undFormtoleranzenThis European Standard was approved by CEN on 10 February 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 754-3:2008: E



EN 754-3:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Tolerances on dimensions.4 2.1 Diameter.4 2.2 Length.4 2.3 Squareness of cut ends.5 3 Tolerances on form.5 3.1 Ovality.5 3.2 Straightness.5 Bibliography.7



EN 754-3:2008 (E) 3 Foreword This document (EN 754-3:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008. This document supersedes EN 754-3:1995. Within its programme of work, Technical committee CEN/TC 132 entrusted CEN/TC 132/WG 5 "Extruded and drawn p
...