SIST EN ISO 22007-1:2018

Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2017)

This document describes the background to methods for the determination of the thermal conductivity
and thermal diffusivity of polymeric materials. Different techniques are available for these
measurements and some may be better suited than others for a particular type, state and form of
material. This document provides a broad overview of these techniques. Standards specific to these
techniques, as referenced in this document, are used to carry out the actual test method.

Kunststoffe - Bestimmung der Wärmeleitfähigkeit und der Temperaturleitfähigkeit - Teil 1: Allgemeine Grundlagen (ISO 22007-1:2017)

In diesem Dokument werden die Grundlagen für Verfahren zur Bestimmung der Wärmeleitfähigkeit und Temperaturleitfähigkeit polymerer Werkstoffe beschrieben. Für diese Messungen stehen unterschiedliche Verfahren zur Verfügung, und für einen bestimmten Werkstofftyp, eine bestimmte Werkstoffbeschaffenheit oder -form können einige Verfahren geeigneter als andere sein. Dieses Dokument gibt einen umfassenden Überblick über diese Verfahren. Die für diese Verfahren entwickelten Normen werden entsprechend den Verweisungen in diesem Dokument für die Durchführung des jeweiligen Prüfverfahrens angewendet.

Plastiques - Détermination de la conductivité thermique et de la diffusivité thermique - Partie 1: Principes généraux (ISO 22007-1:2017)

L'ISO 22007-1 :2017 décrit les principes de base des méthodes permettant de déterminer la conductivité thermique et la diffusivité thermique des matériaux polymères. Différentes techniques de mesurage sont disponibles et certaines peuvent être mieux adaptées que d'autres pour un type, un état et une forme particuliers du matériau. L'ISO 22007-1 :2017 donne un aperçu général de ces techniques. Les normes propres à ces techniques, telles que mentionnées dans le présent document, sont utilisées pour la mise en ?uvre de la méthode d'essai réelle.

Polimerni materiali - Ugotavljanje toplotne prevodnosti in toplotne razprševalnosti - 1. del: Splošna načela (ISO 22007-1:2017)

Ta dokument opisuje ozadje metod za ugotavljanje toplotne prevodnosti in toplotne razprševalnosti polimernih materialov. Za te meritve so na voljo različne tehnike, pri čemer so nekatere lahko primernejše od drugih za posamezno vrsto, stanje in obliko materiala. Ta dokument vsebuje obsežen pregled teh tehnik. Za izvajanje dejanske preskusne metode se uporabljajo standardi za te tehnike, kakor je opisano v tem dokumentu.

General Information

• Status: Withdrawn
• Public Enquiry End Date: 06-Sep-2016
• Publication Date: 03-Jan-2018
• Withdrawal Date: 10-Apr-2024
• ICS: 83.080.01 - Plastics in general
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 26-Mar-2024
• Due Date: 18-Apr-2024
• Completion Date: 11-Apr-2024
• Ref Project: EN ISO 22007-1:2017 - Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2017)

Relations

• Replaces: SIST EN ISO 22007-1:2012 - Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2009)
• Effective Date: 06-Dec-2017
• Revises: SIST EN ISO 22007-1:2024 - Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2024)
• Effective Date: 19-Jan-2023
• Revised: SIST EN ISO 22007-1:2012 - Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General principles (ISO 22007-1:2009)
• Effective Date: 18-Feb-2015

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 22007-1:2018
01-februar-2018
1DGRPHãþD
SIST EN ISO 22007-1:2012
3ROLPHUQLPDWHULDOL8JRWDYOMDQMHWRSORWQHSUHYRGQRVWLLQWRSORWQHUD]SUãHYDOQRVWL
GHO6SORãQDQDþHOD,62
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General
principles (ISO 22007-1:2017)
Kunststoffe - Bestimmung der Wärmeleitfähigkeit und der Temperaturleitfähigkeit - Teil 1:
Allgemeine Grundlagen (ISO 22007-1:2017)
Plastiques - Détermination de la conductivité thermique et de la diffusivité thermique -
Partie 1: Principes généraux (ISO 22007-1:2017)
Ta slovenski standard je istoveten z: EN ISO 22007-1:2017
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 22007-1:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 22007-1:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 22007-1:2018


EN ISO 22007-1
EUROPEAN STANDARD

NORME EUROPÉENNE

November 2017
EUROPÄISCHE NORM
ICS 83.080.01 Supersedes EN ISO 22007-1:2012
English Version

Plastics - Determination of thermal conductivity and
thermal diffusivity - Part 1: General principles (ISO 22007-
1:2017)
Plastiques - Détermination de la conductivité Kunststoffe - Bestimmung der Wärmeleitfähigkeit und
thermique et de la diffusivité thermique - Partie 1: der Temperaturleitfähigkeit - Teil 1: Allgemeine
Principes généraux (ISO 22007-1:2017) Grundlagen (ISO 22007-1:2017)
This European Standard was approved by CEN on 3 August 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22007-1:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 22007-1:2018
EN ISO 22007-1:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 22007-1:2018
EN ISO 22007-1:2017 (E)
European foreword
This document (EN ISO 22007-1:2017) has been prepared by Technical Committee ISO/TC 61 “Plastics”
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018, and conflicting national standards shall be
withdrawn at the latest by May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 22007-1:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 22007-1:2017 has been approved by CEN as EN ISO 22007-1:2017 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 22007-1:2018

---------------------- Page: 6 --
...

SLOVENSKI STANDARD
oSIST prEN ISO 22007-1:2016
01-september-2016
3ROLPHUQLPDWHULDOL8JRWDYOMDQMHWRSORWQHSUHYRGQRVWLLQWRSORWQHUD]SUãHYDOQRVWL
GHO6SORãQDQDþHOD,62',6
Plastics - Determination of thermal conductivity and thermal diffusivity - Part 1: General
principles (ISO/DIS 22007-1:2016)
Kunststoffe - Bestimmung der Wärmeleitfähigkeit und der Temperaturleitfähigkeit - Teil 1:
Allgemeine Grundlagen (ISO/DIS 22007-1:2016)
Plastiques - Détermination de la conductivité thermique et de la diffusivité thermique -
Partie 1: Principes généraux (ISO/DIS 22007-1:2016)
Ta slovenski standard je istoveten z: prEN ISO 22007-1
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 22007-1:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 22007-1:2016

---------------------- Page: 2 ----------------------
oSIST prEN ISO 22007-1:2016
DRAFT INTERNATIONAL STANDARD
ISO/DIS 22007-1
ISO/TC 61/SC 5 Secretariat: DIN
Voting begins on: Voting terminates on:
2016-06-15 2016-09-06
Plastics — Determination of thermal conductivity and
thermal diffusivity —
Part 1:
General principles
Plastiques — Détermination de la conductivité thermique et de la diffusivité thermique —
Partie 1: Principes généraux
ICS: 83.080.01
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 22007-1:2016(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2016

---------------------- Page: 3 ----------------------
oSIST prEN ISO 22007-1:2016
ISO/DIS 22007-1:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 22007-1:2016
ISO/DIS 22007-1:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principles . 2
5 Test methods . 3
5.1 General .
...