SIST EN 1870-3:2015

Safety of woodworking machines - Circular sawing machines - Part 3:Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches

This document deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches, herein after referred to as "machines", designed to cut solid wood, chipboard, fibreboard, plywood and also these materials where they are covered with plastic edging and/or plastic/light alloy laminates when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
NOTE 1   For the definition of down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches, see 3.2, 3.3 and 3.4, and for the definition of displaceable machine, see 3.8.
This document does not apply to:
-  machines for cross cutting logs;
-  hand-held motor-operated electric tools or any adaptation permitting their use in a different mode, i.e. bench mounting;
NOTE 2   Hand-held motor-operated electric tools and saw benches to form an integrated whole with a hand-held motor-operated electric tools are covered by EN 60745-1:2009 together with EN 60745-2-5:2009.
-  transportable machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand.
NOTE 3   Transportable motor-operated electric tools are covered by the requirements of EN 61029-1:2009 together with EN 61029-2-9:2009 and EN 61029-2-11:2009.
This document is not applicable to down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches which are manufactured before the date of its publication as European Standard.

Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 3: Von oben schneidende Kappsägemaschinen und kombinierte Kapp- und Tischkreissägemaschinen

Diese Europäische Norm behandelt alle im Abschnitt 4 aufgeführten Gefährdungen, Gefährdungssituationen und Gefährdungs¬ereignisse, die zutreffen auf stationäre Fräsmaschinen für vierseitige Bearbeitung mit einer größtmöglichen Arbeitsbreite von 350 mm und einer größtmöglichen Geschwindigkeit des mechanischen Werkstückvorschubs von 200 m min1, mit elektrischer und/oder elektronischer Steuerung, im folgenden als "Maschinen" bezeichnet, die konstruiert sind zum Bearbeiten von Massivholz, Spanplatten, Faserplatten oder Sperrholz, sowie diesen Werkstoffen, wenn sie kunststoffbeschichtet oder mit Kantenmaterial versehen sind, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers einschließlich vernünftigerweise vorhersehbarer Fehlanwendung verwendet werden (siehe 6.3 c)).
Hinsichtlich der Definition einer stationären Maschine siehe 3.22.
Diese Europäische Norm behandelt auch die Gefährdungen, die sich auf folgende optionale Arbeitseinheiten beziehen:
-   Universalspindel;
-   Glasleistentrennaggregat.
Diese Europäische Norm ist nicht anzuwenden auf Maschinen, die zur Bearbeitung von Rundholz konstruiert sind, welches nicht vorbearbeitet worden ist.
Diese Europäische Norm behandelt nicht irgendwelche Gefährdungen im Zusammenhang mit:
a)   Einschubeinrichtungen (Magazine, Aufgabebehälter usw.); für mechanische Einschubeinrichtungen, die auch den Zugriff zur Einschuböffnung verhindern, siehe 5.3.7.2;
b)   der Kombination von einzelnen Maschinen mit irgend einer anderen Maschine, die als Teil einer Linie verwendet werden;
c)   Ausschubeinrichtungen (z. B. mechanische Transportsysteme) mit Ausnahme von Gefährdungen durch Wegschleudern als Folge von Gleichlauffräsen.
Diese Europäische Norm gilt nicht für Fräsmaschinen für vierseitige Bearbeitung, die vor dem Datum seiner Veröffentlichung als EN hergestellt wurden.

Sécurité des machines pour le travail du bois - Machines à scies circulaires - Partie 3: Tronçonneuses à coupe descendante et tronçonneuses mixtes à coupe descendante/scies à table

Le présent document traite de tous les phénomènes dangereux, situations et événements dangereux significatifs, tels qu’énumérés à l’Article 4, qui sont applicables aux tronçonneuses à coupe descendante et tronçonneuses mixtes à coupe descendante et à scies circulaires à table de menuisier, ci-après désignées "machines", conçues pour la coupe de bois massif, de panneaux de particules, de panneaux de fibres, de contreplaqué ainsi que ces matériaux lorsque leurs surfaces ou leurs chants sont recouverts de matière plastique et/ou de plastique/alliages légers stratifiés, lorsqu’elles sont utilisées comme prévu et dans les conditions prévues par le fabricant, incluant une mauvaise utilisation raisonnablement prévisible.
NOTE 1   Pour la définition des tronçonneuses à coupe descendante et des tronçonneuses mixtes à coupe descendante et à scies circulaires à table de menuisier, voir 3.2.2, 3.2.3 et 3.2.4, et pour la définition de machine transportable, voir 3.2.8.
Le présent document ne s’applique pas aux :
-   machines conçues pour le tronçonnage de grumes ;
-   machines-outils à moteur électrique portatives, ou toute adaptation permettant leur utilisation de manière différente, c'est-à-dire fixées sur un établi ;
NOTE 2   Les machines-outils à moteur électrique portatives et les scies à table de menuisier destinées à former un ensemble intégré avec une machine-outil à moteur électrique portative sont couvertes par l'EN 60745-1:2009 conjointement avec l'EN 60745-2-5:2010.
-   machines transportables montées sur un établi ou une table similaire à un établi, qui sont conçues pour réaliser un travail à poste fixe, qui peuvent être soulevées à la main par une seule personne, c'est-à-dire d'une masse maximale ≤ 25 kg.
NOTE 3   Les outils électriques à moteur transportables sont couverts par les prescriptions de l'EN 61029-1:2009, conjointement avec l'EN 61029-2-9:2009 et l'EN 61029-2-11:2009.
Le présent document n’est pas applicable aux tronçonneuses à coupe descendante et tronçonneuses mixtes à coupe descendante et à scies circulaires à table de menuisier qui ont été fabriquées avant sa date de publication en tant que Norme européenne.

Varnost lesnoobdelovalnih strojev - Krožne žage - 3. del: Krožne žage za prečni rez od zgoraj navzdol in kombinirane žage za prečni rez z delovno mizo

Ta dokument obravnava vsa večja tveganja, nevarne razmere in dogodke iz točke 4, ki se nanašajo na krožne žage za prečni rez od zgoraj navzdol in kombinirane žage za prečni rez z delovno mizo, v nadaljnjem besedilu »stroji«, ki so namenjene rezanju polnega lesa, ivernih plošč, vlaknenih plošč, vezanih plošč in teh materialov, prevlečenih s plastično obrobo in/ali plastjo iz plastike/lahkih zlitin, ter se uporabljajo v skladu z namenom in pod pogoji, ki jih je predvidel proizvajalec, vključno z razumno predvideno nepravilno uporabo.
OPOMBA 1 Za definicije za krožne žage za prečni rez od zgoraj navzdol in kombinirane žage za prečni rez z delovno mizo glej 3.2, 3.3 in 3.4, za definicijo premestljivega stroja pa 3.8.
Ta dokument se ne uporablja za:
– stroje za prečno rezanje hlodov;
– ročna motorna električna orodja ali kakršne koli prilagoditve, ki omogočajo uporabo na drugačen način, tj. namestitev na delovno mizo;
OPOMBA 2 Ročna motorna električna orodja in žage z delovno mizo za sestavo integrirane celote z ročnimi motornimi električnimi orodji so obravnavane v standardu EN 60745-1:2009 skupaj s standardom EN 60745-2-5:2009;
– premične stroje na delovni mizi ali njej podobni mizi, ki so namenjeni delu v stacionarnem položaju in jih lahko z roko dvigne ena oseba.
OPOMBA 3 Premični motorni električni stroji so obravnavani v zahtevah standarda EN 61029-1:2009 skupaj s standardoma EN 61029-2-9:2009 in EN 61029-2-11:2009.
Ta dokument ne velja za krožne žage za prečni rez od zgoraj navzdol in kombinirane žage za prečni rez z delovno mizo, ki so izdelane pred datumom objave dokumenta kot evropskega standarda.

General Information

• Status: Published
• Public Enquiry End Date: 30-Nov-2012
• Publication Date: 18-Jan-2015
• ICS: 25.080.60 - Sawing machines
• ICS: 79.120.10 - Woodworking machines
• Technical Committee: VSN - Safety of machinery
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 12-Dec-2014
• Due Date: 16-Feb-2015
• Completion Date: 19-Jan-2015
• Directive: 2004/96/EC - Commission Directive 2004/96/EC amending Council Directive 76/769/EEC as regards restrictions on the marketing and use of nickel for piercing post assemblies for the purpose of adapting its Annex I to technical progress
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: EN 1870-3:2014 - Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches

Relations

• Replaces: SIST EN 1870-3:2002+A1:2009 - Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
• Effective Date: 01-Feb-2015
• Replaces: SIST EN 1870-3:2002+A1:2009 - Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 1870-3:2015
01-februar-2015
1DGRPHãþD
SIST EN 1870-3:2002+A1:2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY.URåQHåDJHGHO.URåQHåDJH]DSUHþQLUH]
RG]JRUDMQDY]GROLQNRPELQLUDQHåDJH]DSUHþQLUH]]GHORYQRPL]R
Safety of woodworking machines - Circular sawing machines - Part 3:Down cutting cross
-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 3: Von oben
schneidende Kappsägemaschinen und kombinierte Kapp- und Tischkreissägemaschinen
Sécurité des machines pour le travail du bois - Machines à scies circulaires - Partie 3:
Tronçonneuses à coupe descendante et tronçonneuses mixtes à coupe
descendante/scies à table
Ta slovenski standard je istoveten z: EN 1870-3:2014
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870-3:2015 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 1870-3:2015

---------------------- Page: 2 ----------------------

SIST EN 1870-3:2015

EUROPEAN STANDARD
EN 1870-3

NORME EUROPÉENNE

EUROPÄISCHE NORM
November 2014
ICS 79.120.10 Supersedes EN 1870-3:2001+A1:2009
English Version
Safety of woodworking machines - Circular sawing machines -
Part 3: Down cutting cross-cut saws and dual purpose down
cutting cross-cut saws/circular saw benches
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scies circulaires - Partie 3: Tronçonneuses à coupe Kreissägemaschinen - Teil 3: Von oben schneidende
descendante et tronçonneuses mixtes à coupe Kappsägemaschinen und kombinierte Kapp- und
descendante et à scies circulaires à table de menuisier Tischkreissägemaschinen
This European Standard was approved by CEN on 11 October 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-3:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 1870-3:2015
EN 1870-3:2014 (E)
Contents Page
Foreword .4
Introduction .6
1 Scope .7
2 Normative references .7
3 Terms and definitions . 10
3.1 General . 10
3.2 Terms and definitions . 10
4 List of significant hazards . 14
5 Safety requirements and/or measures . 17
5.1 General . 17
5.2 Controls . 17
5.2.1 Safety and reliability of control systems . 17
5.2.2 Position of controls . 18
5.2.3 Starting . 19
5.2.4 Normal stopping . 20
5.2.5 Emergency stop . 21
5.2.6 Integrated feed . 21
5.2.7 Mode selection . 21
5.2.8 Failure of the power supply . 22
5.3 Protection against mechanical hazards . 22
5.3.1 Stability . 22
5.3.2 Risk of break-up during operation . 22
5.3.3 Tool holder and tool design . 23
5.3.4 Braking . 24
5.3.5 Devices to minimize the possibility or the effect of ejection . 25
5.3.6 Workpiece supports and guides . 30
5.3.7 Prevention of access to moving parts . 36
5.3.8 Clamping devices . 41
5.3.9 Safety appliances. 42
5.4 Protection against non-mechanical hazards . 42
5.4.1 Fire . 42
5.4.2 Noise . 42
5.4.3 Emission of chips and dust . 43
5.4.4 Electricity . 44
5.4.5 Ergonomics and handling . 45
5.4.6 Lighting . 45
5.4.7 Pneumatics . 46
5.4.8 Substances . 46
5.4.9 Electromagnetic compatibility . 46
5.4.10 Laser . 46
5.4.11 Errors of fitting . 46
5.4.12 Isolation . 46
5.4.13 Maintenance . 47
6 Information for use . 47
6.1 General . 47
6.2 Marking . 47
6.2.1 Riving knife marking . 47
6.2.2 Machine marking. 48
2

---------------------- Page: 4 ----------------------

SIST EN 1870-3:2015
EN 1870-3:2014 (E)
6.3 Instruction handbook . 48
Annex A (normative) Dimensional tolerances of saw spindles . 52
Annex B (normative) Riving knife mounting strength test . 53
Annex C (normative) Riving knife lateral stability test . 54
Annex D (normative) Braking tests . 55
D.1 Conditions for all tests . 55
D.2 Tests . 55
D.2.1 Un-braked run-down time . 55
D.2.2 Braked run-down time . 55
Annex E (normative) Impact test method for guards . 56
E.1 General . 56
E.2 Test method . 56
E.2.1 Preliminary remarks . 56
E.2.2 Testing equipment . 56
E.2.3 Projectile for guards . 56
E.2.4 Sampling. 56
E.2.5 Test procedure . 56
E.3 Results . 56
E.4 Assessment . 57
E.5 Test report . 57
E.6 Test equipment for impact test . 57
Annex ZA (informative) Relationship between this European Standard and the Essential

Requirements of EU Directive 2006/42/EC . 59
Bibliography . 62

3

---------------------- Page: 5 ----------------------

SIST EN 1870-3:2015
EN 1870-3:2014 (E)
Foreword
This document (EN 1870-3:2014) has been prepared by Technical Committee CEN/TC 142 “Woodworking
machines - Safety”, the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2015, and conflicting national standards shall be withdrawn at the
latest by May 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
The main modifications compared to EN 1870-3:2001+A1:2009 relate to the introduction of performance
levels (PL) for control systems and to the following items:
— clarification of controls positions in 5.2.2;
— addition of PL where missing;
— addition of requirements on mode selection in 5.2.7 and on prevention of automatic restart in 5.2.8;
— deletion of material requirements on flanges in 5.3.3.3;
— addition of requirements on braking system in 5.3.4;
— up-date of references;
— addition of requirements in 5.4.3 on chips and dust performances;
— limitation of tightening torque for riving knife mounting screws in Annex B.
Organisations contributing to the preparation of this European Standard include the European Committee of
Woodworking Machinery Manufacturers Association “EUMABOIS”.
EN 1870, Safety of woodworking machines — Circular sawing machines, consists of the following parts:
— Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches;
— Part 4: Multi-blade rip sawing machines with manual loading and/or unloading;
— Part 5: Circular saw benches/up-cutting cross-cut sawing machines;
— Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for
firewood/circular saw benches, with manual loading and/or unloading;
— Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or
unloading;
— Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading
and/or unloading;
4

---------------------- Page: 6 ----------------------

SIST EN 1870-3:2015
EN 1870-3:2014 (E)
— Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual
loading and/or unloading;
— Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines;
— Part 11: Semi-automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws);
— Part 12: Pendulum cross-cut sawing machines;
— Part 13: Horizontal beam panel sawing machines;
— Part 14: Vertical panel sawing machines;
— Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading
and/or unloading;
— Part 16: Double mitre sawing machines for V-cutting;
— Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm
saws);
— Part 18: Dimension saws;
— Part 19: Circular saw benches (with and without sliding table) and building site saws.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
5

---------------------- Page: 7 ----------------------

SIST EN 1870-3:2015
EN 1870-3:2014 (E)
Introduction
This document has been prepared to be a harmonized standard to provide one means of conforming to the
essential safety requirements of the Machinery Directive, and associated EFTA regulations. This European
Standard is a type “C” standard as defined in EN ISO 12100:2010.
The extent to which hazards are covered is indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of other standards, for machines that
have been designed and built according to the provisions of this type C standard.
The requirements of this document are directed to manufacturers and their authorized representatives of
down cutting cross-cut saws and dual purpose down cutting cross -cut saws/circular saw benches. They are
also useful for designers.
This document also includes information to be provided by the manufacturer to the user.
Common requirements for tooling are given in EN 847-1:2013.
Electrically driven machines excluded by the scope of this document are covered by the requirements of
EN 61029-1:2000, EN 61029-2-9:2009 and EN 61029-2-11:2009.
6

---------------------- Page: 8 ----------------------

SIST EN 1870-3:2015
EN 1870-3:2014 (E)
1 Scope
This European Standard deals with all significant hazards, hazardous situations and events as listed in
Clause 4 which are relevant to down cutting cross-cut saws and dual purpose down cutting cross-cut
saws/circular saw benches, herein after referred to as “machines”, designed to cut solid wood, chipboard,
fibreboard, plywood and also these materials where they are covered with plastic edging and/or plastic/light
alloy laminates when they are used as intended and under the conditions foreseen by the manufacturer
including reasonably foreseeable misuse.
NOTE 1 For the definition of down cutting cross-cut saws and dual purpose down cutting cross -cut saws/circular saw
benches, see 3.2.2, 3.2.3 and 3.2.4, and for the definition of displaceable machine, see 3.2.8.
This document does not apply to:
— machines for cross cutting logs;
— hand-held motor-operated electric tools or any adaptation permitting their use in a different mode, e.g.
bench mounting;
NOTE 2 Hand-held motor-operated electric tools and saw benches to form an integrated whole with a hand-held motor-
operated electric tools are covered by EN 60745-1:2009 together with EN 60745-2–5:2010.
— transportable machines set up on a bench or a table similar to a bench, which are intended to carry out
work in a stationary position, capable of being lifted by one person by hand i.e. maximum mass ≤ 25 kg.
NOTE 3 Transportable motor-operated electric tools are covered by the requirements of EN 61029-1:2009 together
with EN 61029-2–9:2009 and EN 61029-2–11:2009.
This document is not applicable to down cutting cross-cut saws and dual purpose down cutting cross-cut
saws/circular saw benches which are manufactured before the date of its publication as European Standard.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 574:1996+A1:2008, Safety of machinery - Two-hand control devices - Functional aspects - Principles for
design
EN 614-1:2006+A1:2009, Safety of machinery - Ergonomic design principles - Part 1: Terminology and
general principles
EN 847-1:2013, Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades
EN 894-1:1997+A1:2008, Safety of machinery - Ergonomics requirements for the design of displays and
control actuators - Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997+A1:2008, Safety of machinery - Ergonomics requirements for the design of displays and
control actuators - Part 2: Displays
EN 894-3:2000+A1:2008, Safety of machinery - Ergonomics requirements for the design of displays and
control actuators - Part 3: Control actuators
EN 953:1997+A1:2009, Safety of machinery - Guards - General requirements for the design and construction
of fixed and movable guards
7

---------------------- Page: 9 ----------------------

SIST EN 1870-3:2015
EN 1870-3:2014 (E)
EN 1005-1:2001+A1:2008, Safety of machinery - Human physical performance - Part 1: Terms and definitions
EN 1005-2:2003+A1:2008, Safety of machinery - Human physical performance - Part 2: Manual handling of
machinery and component parts of machinery
EN 1005-3:2002+A1:2008, Safety of machinery - Human physical performance - Part 3: Recommended force
limits for machinery operation
EN 1005-4:2005+A1:2008, Safety of machinery - Human physical performance - Part 4: Evaluation of working
postures and movements in relation to machinery
EN 1837:1999+A1:2009, Safety of machinery - Integral lighting of machines
EN 1870-19:2013, Safety of woodworking machines - Circular sawing machines - Part 19: Circular saw
benches (with and without sliding table) and building site saws
EN 50370-1:2005, Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1:
Emission
EN 50370-2:2003, Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2:
Immunity
EN 50525-2-21:2011, Electric cables - Low voltage energy cables of rated voltages up to and including
450/750 V (Uo/U) - Part 2-21: Cables for general applications - Flexible cables with crosslinked elastomeric
insulation
)
1
EN 60204-1:2006 , Safety of machinery — Electrical equipment of machines — Part 1: General
requirements (IEC 60204-1:2005, modified)
)
2
EN 60439-1:1999 , Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially
type-tested assemblies (IEC 60439-1:1999 + A1:2004)
)
3
EN 60529:1991 , Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989 + A1:1999)
EN 60825-1:2007, Safety of laser products - Part 1: Equipment classification and requirements
(IEC 60825-1:2007)
EN 61310-1:2008, Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual,
acoustic and tactile signals (IEC 61310-1:2007)
EN 61496-2:2013, Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular
requirements for equipment using active opto-electronic protective devices (AOPDs) (IEC 61496-2:2013)
EN 61800-5-2:2007, Adjustable speed electrical power drive systems - Part 5-2: Safety requirements –
Functional (IEC 61800-5-2:2007)
EN ISO 3743-1:2010, Acoustics - Determination of sound power levels and sound energy levels of noise
sources using sound pressure - Engineering methods for small movable sources in reverberant fields - Part 1:
Comparison method for a hard-walled test room (ISO 3743-1:2010)

1) EN 60204-1:2006 is amended by EN 60204-1:2006/A1:2009, based on IEC 60204-1:2005/A1:2008.
)
2
EN 60439-1:1999 is impacted by EN 60439-1:1999/A1:2004.
)
3
EN 60529:1991 is impacted by EN 60529:1991/A1:2000.
8

---------------------- Page: 10 ----------------------

SIST EN 1870-3:2015
EN 1870-3:2014 (E)
EN ISO 3743-2:2009, Acoustics - Determination of sound power levels of noise sources using sound pressure
- Engineering methods for small, movable sources in reverberant fields - Part 2: Methods for special
reverberation test rooms (ISO 3743-2:1994)
EN ISO 3744:2010, Acoustics - Determination of sound power levels and sound energy levels of noise
sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO
3744:2010)
EN ISO 3745:2012, Acoustics - Determination of sound power levels and sound energy levels of noise
sources using sound pressure - Precision methods for anechoic rooms and hemi-anechoic rooms (ISO
3745:2012)
EN ISO 3746:2010, Acoustics - Determination of sound power levels and sound energy levels of noise
sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting
plane (ISO 3746:2010)
EN ISO 4414:2010, Pneumatic fluid power - General rules and safety requirements for systems and their
components (ISO 4414:2010)
EN ISO 4871:2009, Acoustics - Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)
EN ISO 9614-1:2009, Acoustics - Determination of sound power levels of noise sources using sound intensity
- Part 1: Measurement at discrete points (ISO 9614-1:1993)
EN ISO 11202:2010, Acoustics - Noise emitted by machinery and equipment - Determination of emission
sound pressure levels at a work station and at other specified positions applying approximate environmental
corrections (ISO 11202:2010)
EN ISO 11204:2010, Acoustics - Noise emitted by machinery and equipment - Determination of emission
sound pressure levels at a work station and at other specified positions applying accurate environmental
corrections (ISO 11204:2010)
EN ISO 11688-1:2009, Acoustics - Recommended practice for the design of low-noise machinery and
equipment - Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 12100:2010, Safety of machinery - General principles for design - Risk assessment and risk reduction
(ISO 12100:2010)
EN ISO 13849-1:2008, Safety of machinery - Safety-related parts of control systems - Part 1: General
principles for design (ISO 13849-1:2006)
EN ISO 13850:2008, Safety of machinery - Emergency stop - Principles for design (ISO 13850:2006)
EN ISO 13856-1:2013, Safety of machinery - Pressure-sensitive protective devices - Part 1: General
principles for design and testing of pressure-sensitive mats and pressure-sensitive floors (ISO 13856-1:2013)
EN ISO 13856-2:2013, Safety of machinery - Pressure-sensitive protective devices - Part 2: General
principles for design and testing of pressure-sensitive edges and pressure-sensitive bars (ISO 13856-2:2013)
EN ISO 13857:2008, Safety of machinery - Safety distances to prevent hazard zones being reached by upper
and lower limbs (ISO 13857:2008)
EN ISO 14119:2013, Safety of machinery - Interlocking devices associated with guards - Principles for design
and selection (ISO 14119:2013)
ISO 7960:1995, Airborne noise emitted by machine tools — Operating conditions for woodworking machines
9

---------------------- Page: 11 ----------------------

SIST EN 1870-3:2015
EN 1870-3:2014 (E)
ISO 14118:2000, Safety of machinery — Prevention of unexpected start-up
3 Terms and definitions
3.1 General
For the purposes of this document, the terms and definitions given in EN ISO 12100:2010 and the following
apply.
3.2 Terms and definitions
3.2.1
cross-cutting
operation of cutting across the grain of a wooden workpiece
3.2.2
down cutting cross-cut saw
machine where the saw blade spindle is situated above the workpiece when the saw blade is in its rest
position and where the saw blade moves down th
...