SIST EN 15151-2:2012
(Main)Mountaineering equipment - Braking devices - Part 2: Manual braking devices, safety requirements and test methods
Mountaineering equipment - Braking devices - Part 2: Manual braking devices, safety requirements and test methods
This European Standard specifies safety requirements and test methods for manual braking devices used in mountaineering, climbing and related activities for belaying and abseiling, with only manual control, to protect against falls from a height. This European Standard applies to braking devices which are loaded with one person and which use mountaineering ropes according to EN 892. In case of abseiling and lowering down this standard also applies to braking devices, used with low stretch kernmantel ropes according to EN 1891.
Bergsteigerausrüstung - Bremsgeräte - Teil 2: Manuelle Bremsgeräte, sicherheitstechnische Anforderungen und Prüfverfahren
Diese Norm legt sicherheitstechnische Anforderungen und Prüfverfahren für Bremsgeräte mit manueller Kontrolle zum Sichern und Abseilen beim Bergsteigen und Klettern fest, um vor einem Absturz aus der Höhe zu schützen.
Diese Europäische Norm gilt für Bremsgeräte, die von einer Person benutzt werden und bei denen Bergseile nach EN 892 verwendet werden. Beim Abseilen und Ablassen gilt diese Norm auch für Kernmantelseile mit geringer Dehnung nach EN 1891.
Equipement d'alpinisme et d'escalade - Dispositifs de freinage - Partie 2: Dispositifs de freinage manuelles, exigences de sécurité et méthodes d'essai
La présente Norme européenne spécifie les exigences de sécurité et les méthodes d'essai applicables aux
dispositifs de freinage manuel utilisés en alpinisme, en escalade et lors d'activités connexes pour l'assurage
et la descente en rappel avec contrôle manuel uniquement, à des fins de protection contre les chutes de
hauteur.
La présente Norme européenne s'applique aux dispositifs de freinage utilisés par une seule personne et avec
des cordes d'alpinisme conformément à l'EN 892. En cas de descente en rappel ou de descente par une
tierce personne, cette norme s’applique également aux dispositifs de freinage utilisés avec des cordes
tressées gainées à faible coefficient d'allongement conformément à l'EN 1891.
Gorniška oprema - Naprave za zaviranje - 2. del: Ročne naprave za zaviranje, varnostne zahteve in preskusne metode
Ta evropski standard določa varnostne zahteve in preskusne metode za ročne naprave za zaviranje, ki se uporabljajo za ročno zaščito pred padci z višine v gorništvu, pri plezanju in s tem povezanih dejavnostih navijanja vrvi in spuščanja po vrvi Ta evropski standard se nanaša na naprave za zaviranje, ki so obremenjene z eno osebo in uporabljajo gorniške vrvi v skladu s standardom EN 892. V primeru spuščanja z vrvjo se ta standard nanaša tudi na naprave za zaviranje, ki se uporabljajo z oplaščenimi statičnimi vrvmi v skladu s standardom EN 1891.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bergsteigerausrüstung - Bremsgeräte - Teil 2: Manuelle Bremsgeräte, sicherheitstechnische Anforderungen und PrüfverfahrenEquipement d'alpinisme et d'escalade - Dispositifs de freinage - Partie 2: Dispositifs de freinage manuelles, exigences de sécurité et méthodes d'essaiMountaineering equipment - Braking devices - Part 2: Manual braking devices, safety requirements and test methods97.220.40Oprema za športe na prostem in vodne športeOutdoor and water sports equipmentICS:Ta slovenski standard je istoveten z:EN 15151-2:2012SIST EN 15151-2:2012en,fr,de01-oktober-2012SIST EN 15151-2:2012SLOVENSKI
STANDARD
SIST EN 15151-2:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15151-2
August 2012 ICS 97.220.40 English Version
Mountaineering equipment - Braking devices - Part 2: Manual braking devices, safety requirements and test methods
Equipement d'alpinisme et d'escalade - Dispositifs de freinage - Partie 2: Dispositifs de freinage manuels, exigences de sécurité et méthodes d'essai
Bergsteigerausrüstung - Bremsgeräte - Teil 2: Manuelle Bremsgeräte, sicherheitstechnische Anforderungen und Prüfverfahren This European Standard was approved by CEN on 30 June 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15151-2:2012: ESIST EN 15151-2:2012
EN 15151-2:2012 (E) 2
Contents Page Foreword .31Scope .42Normative references .43Terms and definitions .44Classification .54.1General .54.2Manual braking devices .55Safety requirements .55.1General .55.2Static strength .65.3Static strength when used as a belay anchor .76Test methods .76.1General .76.2Test conditions .76.3Sampling .76.4Design .76.5Static strength .86.6Static strength of the additional attachment .97Marking .98Information supplied by the manufacturer . 10Annex A (informative)
Standards on mountaineering equipment . 12Bibliography . 13 SIST EN 15151-2:2012
EN 15151-2:2012 (E)
3 Foreword This document (EN 15151-2:2012) has been prepared by Technical Committee CEN/TC 136 “Sports, playground and other recreational facilities and equipment”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2013, and conflicting national standards shall be withdrawn at the latest by February 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This European Standard EN 15151 "Mountaineering equipment - Braking devices" consists of: Part 1: Braking devices with assisted locking, safety requirements and test methods; Part 2: Manual braking devices, safety requirements and test methods. This standard is one of a package of standards for mountaineering equipment (see Annex A). According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 15151-2:2012
EN 15151-2:2012 (E) 4
1 Scope This European Standard specifies safety requirements and test methods for manual braking devices used in mountaineering, climbing and related activities for belaying and abseiling, with only manual control, to protect against falls from a height. This European Standard applies to braking devices which are loaded with one person and which use mountaineering ropes according to EN 892. In case of abseiling and lowering down this standard also applies to braking devices, used with low stretch kernmantel ropes according to EN 1891.
2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 892, Mountaineering equipment — Dynamic mountaineering ropes — Safety requirements and test methods EN 1891, Personal protective equipment for the prevention of falls from a height — Low stretch kernmantel ropes EN 15151-1:2012, Mountaineering equipment — Braking devices — Part 1: braking devices with manually assisted locking, safety requirements and test methods 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 braking device mechanical device which generates forces on the rope, to oppose movement of the rope through the device 3.2 manual braking device device controlled by hand force applied to the free end of the rope, that produces a magnified force in the active rope in a continuous and reversible manner, such that when the force in the free end of the rope is reduced to zero, the braking effect becomes negligibly small 3.3 attachment point any system which is required and intended for the attachment of a connector according to the information supplied by the manufacturer
Note 1 to entry: For information on connectors, see EN 12275 or EN 362. 3.4
function to adjust the friction inherent characteristic of the device that allows the friction to be changed
SIST EN 15151-2:2012
EN 15151-2:2012 (E)
5 4 Classification 4.1 General Figure 1 gives the classification of braking devices used in mountaineering, climbing and related activities. Manual braking devices are classified according to 4.2. Braking devices with manually assisted locking are defined in EN 15151-1:2012, 4.2.
Key A abseiling B belaying Figure 1 — Classification of braking devices 4.2 Manual braking devices 4.2.1 Type 1: devices for abseiling without a function to adjust the friction; 4.2.2 Type 2: devices for belaying and abseiling without a function to adjust the friction; 4.2.3 Type 3: devices for abseiling with a function to adjust the friction; 4.2.4 Type 4: devices for belaying and abseiling with a function to adjust the friction. 5 Safety requirements 5.1 General 5.1.1 An overview of the requirements related to the various types of manual braking device is given in SIST EN 15151-2:2012
EN 15151-2:2012 (E) 6
Table 1. Requirements for braking devices with manually assisted locking are given in EN 15151-1:2012. Table 1 — Overview of requirements related to various types of manual braking devices Clause Requirem
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.