SIST EN 61755-3-8:2009

Fibre optic interconnecting devices and passive components - Fibre optic connector optical interfaces - Part 3-8: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical 8 degrees angled-APC composite ferrule using titanium as fibre surrounding material, single mode fibre (IEC 61755-3-8:2009)

This part of IEC 61755 defines dimensional limits and material properties of a 2,5 mm and a 1,25 mm diameter cylindrical composite ferrule optical interface to meet specific requirements for APC fibre-to-fibre interconnection. The composite ferrule uses different materials in the end face contact zone and in ferrule to sleeve contact zone. The specified materials for each zone are zirconia (ZrO2) for the ferrule to sleeve contact zone and titanium for the end face contact zone. Ferrules made from the material specified in this standard are suitable for use in categories C, U, E and O as defined in IEC 61753-1.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Optische Schnittstellen von Lichtwellenleiter-Steckverbindern - Teil 3-8: Optische Schnittstelle - Zylindrische 8 Grad abgeschrägte APC-Composite-Ferrulen mit 2,5 mm und 1,25 mm Durchmesser für Einmodenfaser, mit Titan als Material für die Faserfassung, Einmoden LWL (IEC 61755-3-8:2009)

Dispositifs d'interconnexion et composants passifs à fibres optiques - Interfaces optiques de connecteurs pour fibres optiques - Partie 3-8: Interfaces optiques, férules composites cylindriques APC-angle de 8 degrés, de diamètre 2,5 mm et 1,25 mm, utilisant le titane comme matériau entourant la fibre, fibres unimodales (CEI 61755-3-8:2009)

La CEI 61755-3-8:2009 définit les limites dimensionnelles et les propriétés du matériau d'une interface optique avec une férule cylindrique en composite de diamètre de 2,5 et 1,25 mm, afin de satisfaire aux exigences des interconnexions fibre-à-fibre APC. La férule composite met en jeu différents matériaux dans la zone de contact des extrémités de fibres, et dans la zone de contact manchon - férule. Les matériaux spécifiques pour chaque zone sont le zircone (ZrO2) pour la zone de contact férule - manchon, et le titane pour la zone de contact de l'extrémité. Les férules constituées par le matériau spécifié dans la présente norme sont adaptées à une utilisation dans les catégories C, U, E et O, telles que définies dans la CEI 61753-1.

Optični spojni elementi in pasivne komponente -Optični vmesniki konektorja optičnih vlaken - 3-8. del: Optični vmesnik, cilindrična tulka s čelom pod kotom 8 stopinj iz kompozita APC s premeroma 2,5 mm in 1,25 mm, obdajajoči material iz titanovih vlaken, enorodno vlakno (IEC 61755-3-8:2009)

General Information

• Status: Published
• Publication Date: 22-Mar-2009
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: iTEL - Communication cables
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 05-Mar-2009
• Due Date: 10-May-2009
• Completion Date: 23-Mar-2009
• Ref Project: EN 61755-3-8:2009 - Fibre optic interconnecting devices and passive components - Fibre optic connector optical interfaces - Part 3-8: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical 8 degrees angled-APC composite ferrule using titanium as fibre surrounding material, single mode fibre

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61755-3-8:2009
01-maj-2009
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2SWLþQLYPHVQLNLNRQHNWRUMD
RSWLþQLKYODNHQGHO2SWLþQLYPHVQLNFLOLQGULþQDWXONDVþHORPSRGNRWRP
VWRSLQML]NRPSR]LWD$3&VSUHPHURPDPPLQPPREGDMDMRþLPDWHULDOL]
WLWDQRYLKYODNHQHQRURGQRYODNQR,(&
Fibre optic interconnecting devices and passive components - Fibre optic connector
optical interfaces - Part 3-8: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical 8
degrees angled-APC composite ferrule using titanium as fibre surrounding material,
single mode fibre (IEC 61755-3-8:2009)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Optische Schnittstellen
von Lichtwellenleiter-Steckverbindern - Teil 3-8: Optische Schnittstelle - Zylindrische 8
Grad abgeschrägte APC-Composite-Ferrulen mit 2,5 mm und 1,25 mm Durchmesser für
Einmodenfaser, mit Titan als Material für die Faserfassung, Einmoden LWL (IEC 61755-
3-8:2009)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Interfaces optiques
de connecteurs pour fibres optiques - Partie 3-8: Interfaces optiques, férules composites
cylindriques APC-angle de 8 degrés, de diamètre 2,5 mm et 1,25 mm, utilisant le titane
comme matériau entourant la fibre, fibres unimodales (CEI 61755-3-8:2009)
Ta slovenski standard je istoveten z: EN 61755-3-8:2009
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61755-3-8:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61755-3-8:2009

---------------------- Page: 2 ----------------------

SIST EN 61755-3-8:2009

EUROPEAN STANDARD
EN 61755-3-8

NORME EUROPÉENNE
February 2009
EUROPÄISCHE NORM

ICS 33.180.20

English version

Fibre optic interconnecting devices and passive components -
Fibre optic connector optical interfaces -
Part 3-8: Optical interface, 2,5 mm and 1,25 mm diameter
cylindrical 8 degrees angled-APC composite ferrule
using titanium as fibre surrounding material, single mode fibre
(IEC 61755-3-8:2009)


Dispositifs d'interconnexion  Lichtwellenleiter -
et composants passifs à fibres optiques - Verbindungselemente
Interfaces optiques de connecteurs und passive Bauteile -
pour fibres optiques - Optische Schnittstellen
Partie 3-8: Interfaces optiques, von Lichtwellenleiter-Steckverbindern -
férules composites cylindriques Teil 3-8: Optische Schnittstelle -
APC-angle de 8 degrés, Zylindrische 8 Grad abgeschrägte
de diamètre 2,5 mm et 1,25 mm, APC-Composite-Ferrulen mit 2,5 mm
utilisant le titane comme matériau und 1,25 mm Durchmesser
entourant la fibre, fibres unimodales für Einmodenfaser, mit Titan als Material
(CEI 61755-3-8:2009) für die Faserfassung, Einmoden LWL
(IEC 61755-3-8:2009)


This European Standard was approved by CENELEC on 2009-02-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: avenue Marnix 17, B - 1000 Brussels


© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61755-3-8:2009 E

---------------------- Page: 3 ----------------------

SIST EN 61755-3-8:2009
EN 61755-3-8:2009 - 2 -
Foreword
The text of document 86B/2769/FDIS, future edition 1 of IEC 61755-3-8, prepared by SC 86B, Fibre optic
interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61755-3-8 on 2009-02-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2009-11-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-02-01
__________
Endorsement notice
The text of the International Standard IEC 61755-3-8:2009 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61753-1 NOTE  Harmonized as EN 61753-1:2007 (not modified).
IEC 61755-3 NOTE  Harmonized in EN 61755-3 series (partially modified).
__________

---------------------- Page: 4 ----------------------

SIST EN 61755-3-8:2009
IEC 61755-3-8
Edition 1.0 2009-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Fibre optic interconnecting devices and passive components – Fibre optic
connector optical interfaces –
Part 3-8: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical 8 degrees
angled-APC composite ferrule using titanium as fibre surrounding material, single
mode fibre

Dispositifs d'interconnexion et composants passifs à fibres optiques – Interfaces
optiques de connecteurs pour fibres optiques –
Partie 3-8: Interfaces optiques, férules composites cylindriques
APC-angle de 8 degrés, de diamètre 2,5 mm et 1,25 mm, utilisant le titane comme
matériau entourant la fibre, fibres unimodales

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
K
CODE PRIX
ICS 33.180.20 ISBN 2-8318-1023-3
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 5 ----------------------

SIST EN 61755-3-8:2009
– 2 – 61755-3-8 © IEC:2009
CONTENTS
FOREWORD.3
1 Scope.5
2 Description .5
3 Interface parameters for APC ferrule independent from the ferrule material.6
Annex A (informative) .9
Bibliography.10

Figure 1 – Interface dimensions for APC ferrule.6
Figure 2 – Fibre core location .6
Figure 3 – Interface dimension of the end face contact zone.7

Table 1 – Optical interface parameter values for 2,5 mm diameter APC ferrule .7
Table 2 – Optical interface parameter values for 1,25 mm diameter APC ferrule .8

---------------------- Page: 6 ----------------------

SIST EN 61755-3-8:2009
61755-3-8 © IEC:2009 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
FIBRE OPTIC CONNECTOR OPTICAL INTERFACES –

Part 3-8: Optical interface, 2,5 mm and 1,25 mm diameter cylindrical
8 degrees angled-APC composite ferrule using titanium as fibre
surrounding material, single mode fibre


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recomm
...