SIST EN ISO 20957-2:2024
(Main)Stationary training equipment - Part 2: Strength training equipment - Additional specific safety requirements and test methods (ISO 20957-2:2024)
Stationary training equipment - Part 2: Strength training equipment - Additional specific safety requirements and test methods (ISO 20957-2:2024)
This document specifies additional safety requirements for stationary strength training equipment.
This document is intended to be read in conjunction with the general safety requirements of ISO 20957‑1.
This document is applicable to stationary training equipment type strength training equipment with stacked weight resistance or other means of resistance, such as elastic cords, hydraulic, pneumatic, electrical, magnetic, springs and externally loaded weights (type 2) (hereinafter referred to as training equipment) with the classes H, S and I according to ISO 20957‑1.
NOTE Free-weight barbell racks are subject to the requirements of ISO 20957‑4 and ISO 20957‑1.
Stationäre Trainingsgeräte - Teil 2: Kraft-Trainingsgeräte, zusätzliche besondere sicherheitstechnische Anforderungen und Prüfverfahren (ISO 20957-2:2024)
Dieses Dokument legt sicherheitstechnische Anforderungen für stationäre Kraft-Trainingsgeräte fest, zusätzlich zu den allgemeinen sicherheitstechnischen Anforderungen nach ISO 20957 1:2013.
Dieses Dokument ist anwendbar für stationäre Kraft-Trainingsgeräte, bei denen der Widerstand durch Steckgewichte oder andere Widerstandsmittel, wie elastische Bänder, Hydraulik, Pneumatik, Elektronik, Magnetkraft, Federn und extern beladene Gewichte der Klassen H, S und I nach ISO 20957 1:2013 aufgebaut wird (im Folgenden stationäre Trainingsgeräte genannt).
ANMERKUNG Für diese Art von stationären Trainingsgeräten gelten keine Genauigkeitsklassen, da Genauigkeitsklassen keinen Einfluss auf die Sicherheit dieser Geräte haben.
Équipement d'entraînement fixe - Partie 2: Équipement d'entraînement de force - Exigences spécifiques de sécurité et méthodes d'essai supplémentaires (ISO 20957-2:2024)
Le présent document spécifie des exigences de sécurité supplémentaires pour les équipements d'entraînement fixes de force.
Le présent document est destiné à être lu conjointement aux exigences de sécurité générales figurant dans l'ISO 20957‑1.
Le présent document s'applique aux équipements d'entraînement fixes de type équipements d'entraînement de force utilisant une résistance à l'aide de piles de poids ou d'autres moyens de résistance comme de la corde élastique, des systèmes hydrauliques, pneumatiques, électriques, magnétiques ou à ressorts et des poids chargés par l'extérieur (type 2) (équipements désignés ci-après par « équipements d'entraînement ») de classes H, S et I, conformément à l'ISO 20957‑1.
NOTE Les supports de poids et d'haltères libres sont soumis aux exigences de l'ISO 20957‑4 et de l'ISO 20957‑1.
Nepremična oprema za vadbo - 2. del: Oprema za vadbo moči, dodatne posebne varnostne zahteve in preskusne metode (ISO 20957-2:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Nadomešča:
SIST EN ISO 20957-2:2021
Nepremična oprema za vadbo - 2. del: Oprema za vadbo moči, dodatne posebne
varnostne zahteve in preskusne metode (ISO 20957-2:2024)
Stationary training equipment - Part 2: Strength training equipment - Additional specific
safety requirements and test methods (ISO 20957-2:2024)
Stationäre Trainingsgeräte - Teil 2: Kraft-Trainingsgeräte, zusätzliche besondere
sicherheitstechnische Anforderungen und Prüfverfahren (ISO 20957-2:2024)
Équipement d'entraînement fixe - Partie 2: Équipement d'entraînement de force -
Exigences spécifiques de sécurité et méthodes d'essai supplémentaires (ISO 20957-
2:2024)
Ta slovenski standard je istoveten z: EN ISO 20957-2:2024
ICS:
97.220.30 Oprema za dvoranske športe Indoor sports equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 20957-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2024
EUROPÄISCHE NORM
ICS 97.220.30 Supersedes EN ISO 20957-2:2021
English Version
Stationary training equipment - Part 2: Strength training
equipment - Additional specific safety requirements and
test methods (ISO 20957-2:2024)
Appareils d'entraînement fixes - Partie 2: Appareil Stationäre Trainingsgeräte - Teil 2: Kraft-
d'entraînement de force - Exigences spécifiques de Trainingsgeräte, zusätzliche besondere
sécurité et méthodes d'essai supplémentaires (ISO sicherheitstechnische Anforderungen und
20957-2:2024) Prüfverfahren (ISO 20957-2:2024)
This European Standard was approved by CEN on 14 September 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 20957-2:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the safety
requirements of Directive 2001/95/EC aimed to be covered . 4
European foreword
This document (EN ISO 20957-2:2024) has been prepared by Technical Committee ISO/TC 83 "Sports
and other recreational facilities and equipment" in collaboration with Technical Committee CEN/TC
136 “Sports, playground and other recreational facilities and equipment” the secretariat of which is held
by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2025, and conflicting national standards shall be
withdrawn at the latest by April 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 20957-2:2021.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 20957-2:2024 has been approved by CEN as EN ISO 20957-2:2024 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the safety requirements
of Directive 2001/95/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request
Standardisation mandate issued to the European standardisation organisations (ESOs) to develop
European standards for stationary training equipment “M/506” to provide one voluntary means of
conforming to the safety requirements of Commission Decision (EU) No 476/2011 of 27 July 2011
implementing General Product Safety Directive 2001/95/EC of the European Parliament and of the
Council with regard to safety requirements for stationary training equipment.
Once this standard is cited in the Official Journal of the European Union under that Directive
2001/95/EC, compliance with the normative clauses of this standard given in Table ZA.1 confers,
within the limits of the scope of this standard, a presumption of conformity with the corresponding
safety requirements of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Commission Decision (EU)
No 476/2011 of 27 July 2011 implementing Directive 2001/95/EC of the European Parliament
and of the Council with regard to safety requirements for stationary training equipment and
Commission’s standardization request Standardisation mandate issued to the European
standardisation organisations (ESOs) to develop European standards for stationary training
equipment ‘M/506’
Safety Requirements of Clause(s)/sub-clause(s) of
EC Decision (EU) No 476/2011 this EN
I. Product and product definition 1; 3; 4
II. A General safety requirements 1; 5.1.1; 5.3.1; 5.8
II. B. Specific Safety Requirements 5.3.1; 5.3.2
(a) Stability of free-standing equipment 5.1
(b) Sharp edges and burrs —
(c) Tube ends —
(d) Squeeze, shear, rotating and reciprocating points within 5.4
the accessible area
(e) Weights 5.2.1; 5.2.2.1; 5.2.2.2; 5.2.2.3;
5.2.2.4; 5.4.1; 5.4.2; 5.5
(f) Equipment access and escape 5.6
(g) Adjustment and locking mechanisms 5.4.1.2; 5.8; 5.9
(h) Ropes, belts and chains 5.2.1
(i) Wire ropes and pulleys —
(j) Rope and belt guides —
(k) Pull-in points 5.7
Safety Requirements of Clause(s)/sub-clause(s) of
EC Decision (EU) No 476/2011 this EN
(l) Gripping positions —
(m) Integral handgrips —
(n) Applied handgrips —
(o) Rotating handgrips —
(p) Electrical safety —
(q) Care and maintenance —
(r) Assembly instructions —
(s) General instructions for use 5.8
(t) Basic biomechanical requirements —
(u) Marking 5.9
(v) Warnings, especially concerning risks for children 5.9
(w) Immobilisation unit especially for children by locking the —
power out
II. B. Tests
(a) Dimensional check 6.1.1
(b) Visual examination 6.1.2
(c) Tactile examination 6.1.3
(d) Performance test 6.1.4
(f) Testing of pull-in points 6.1.1; 6.1.2; 6.1.4
(h) Stability test 6.2
(i) Determination of breaking load of ropes, belts and chains 5.2.1
(l) Testing of access/escape 6.1.1; 6.1.2; 6.1.4
(m) Testing of endurance load 6.4.1
(q) Test report 7
Other tests – Static Load Testing 6.3
Other tests – Impact Testing 6.4.2
WARNING 1 Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 Other Union legislation may be applicable to the products falling within the scope of
this standard.
International
Standard
ISO 20957-2
Third edition
Stationary training equipment —
2024-09
Part 2:
Strength training equipment
— Additional specific safety
requirements and test methods
Appareils d’entraînement fixes —
Partie 2: Appareil d’entraînement de force — Exigences
spécifiques de sécurité et méthodes d’essai supplémentaires
Reference number
ISO 20957-2:2024(en) © ISO 2024
ISO 20957-2:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 20957-2:2024(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 5
5 Safety requirements. 6
5.1 Stability .6
5.1.1 General .6
5.1.2 Externally loaded equipment .6
5.1.3 User-defined motion equipment .6
5.2 Loading .6
5.2.1 Selectorized equipment and alternative resistance training equipment .6
5.2.2 Externally loaded equipment .6
5.3 Endurance .7
5.3.1 General .7
5.3.2 Additional requirements for externally loaded equipment .8
5.4 Access to squeeze and/or shear points .8
5.4.1 Stacked weights or alternative means of resistance .8
5.4.2 Weight disc clearance for externally loaded weights . 13
5.5 Weight disc retention .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.