SIST EN 14605:2005
(Main)Protective clothing against liquid chemicals - Performance requirements for clothing with liquid-tight (Type 3) or spray-tight (Type 4) connections, including items providing protection to parts of the body only (Types PB [3] and PB [4])
Protective clothing against liquid chemicals - Performance requirements for clothing with liquid-tight (Type 3) or spray-tight (Type 4) connections, including items providing protection to parts of the body only (Types PB [3] and PB [4])
This European Standard specifies the minimum requirements for the following types of limited use and reusable chemical protective clothing:
- clothing with liquid-tight connections between different parts of the clothing (type 3: liquid-tight clothing) and, if applicable, with liquid-tight connections to component parts, such as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards. Such garments are full-body protective clothing, such as one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or overbooties, with or without gloves;
- clothing with spray-tight connections between different parts of the clothing (type 4: spray-tight clothing) and, if applicable, spray-tight connections to component parts, such as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards. Such garments are full-body protective clothing, such as one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or overbooties, with or without gloves;
- garments offering protection to specified parts of the body against permeation of chemical liquids (partial body chemical protective clothing). Such garments are e.g. laboratory coats, jackets, trousers, aprons, sleeves, hoods (not air-supplied) etc. As partial body protective garments leave part of the body unprotected this standard specifies only the performance requirements of the clothing material and the seams.
NOTE Partial body chemical protective garments which offer only protection against penetration of chemical liquids are within the scope of prEN 13034 (type 6 clothing).
Schutzkleidung gegen flüssige Chemikalien - Leistungsanforderungen an Chemikalienschutzanzüge mit flüssigkeitsdichten (Typ 3) oder spraydichten (Typ 4) Verbindungen zwischen den Teilen der Kleidung, einschließlich der Kleidungsstücke, die nur einen Schutz für Teile des Körpers gewähren (Typen PB [3] und PB [4])
Dieses Dokument legt die Mindestanforderungen für folgende Typen für begrenzte Anwendung bestimmter
sowie wiederverwendbarer Chemikalienschutzkleidung fest:
. Ganzkörperschutzkleidung mit flüssigkeitsdichten Verbindungen zwischen den verschiedenen Teilen der
Kleidung (Typ 3: flüssigkeitsdichte Kleidung) und, falls anwendbar, mit flüssigkeitsdichten Verbindungen
zu Zubehörteilen wie Hauben, Handschuhe, Stiefel, Sichtscheiben oder Atemschutzausrüstungen, für die
in anderen Europäischen Normen Festlegungen bestehen können.
Beispiele für solche Kleidung sind einteilige Overalls oder zweiteilige Anzüge mit oder ohne Haube oder
Sichtscheibe, mit oder ohne Füßlinge oder Überschuhe, mit oder ohne Handschuhe.
. Ganzkörperschutzkleidung mit spraydichten Verbindungen zwischen den verschiedenen Teilen der
Kleidung (Typ 4: spraydichte Kleidung) und, falls anwendbar, mit spraydichten Verbindungen zu
Zubehörteilen wie Hauben, Handschuhe, Stiefel, Sichtscheiben oder Atemschutzausrüstungen, für die in
anderen Europäischen Normen Festlegungen bestehen können.
Beispiele für solche Kleidung sind einteilige Overalls oder zweiteilige Anzüge mit oder ohne Haube oder
Sichtscheibe, mit oder ohne Füßlinge oder Überschuhe, mit oder ohne Handschuhe.
. Teilkörperschutzkleidungsstücke, die bestimmten Teilen des Körpers Schutz gegen die Permeation
flüssiger Chemikalien bieten.
Beispiele für solche Kleidungsstücke sind z. B. Labormäntel, Jacken, Hosen, Schürzen, Ärmel, Hauben
(ohne Luftzufuhr) usw. Da Teilkörperschutz einen Teil des Körpers ungeschützt lässt, legt dieses
Dokument nur die Leistungsanforderungen für das Bekleidungsmaterial und die Nähte fest.
ANMERKUNG Chemikalienschutzkleidung für Teile des Körpers, die nur Schutz gegen die Penetration flüssiger
Chemikalien bietet, gehört zum Anwendungsbereich von prEN 13034 (Kleidung Typ 6).
Vetements de protection contre les produits chimiques liquides - Exigences relatives aux vetements dont les éléments de liaison sont étanches au liquide (Type 3) ou aux pulvérisations (Type 4), y compris les articles d'habillement protégeant seulement certaines parties du corps (Types PB (3) et PB (4))
La présente Norme européenne spécifie les exigences minimales demandées aux types suivants de vetements de protection chimique a usage limité ou réutilisables :
- vetements protégeant tout le corps dotés de liaisons étanches aux liquides entre les différentes parties du vetement (Type 3 : vetements étanches aux liquides) et, s'il y a lieu, de liaisons étanches aux liquides entre le vetement et les éléments constitutifs tels que cagoules, gants, bottes, oculaires ou appareils de protection respiratoire, susceptibles d'etre spécifiés dans d'autres Normes européennes, comme par exemple les combinaisons une piece ou deux pieces, avec ou sans cagoule ou oculaire, avec ou sans bottes intégrées ou sur- bottes, avec ou sans gants ;
- vetements protégeant tout le corps dotés de liaisons étanches aux brouillards entre les différentes parties du vetement (Type 4 : vetements étanches aux brouillards) et, s'il y a lieu, de liaisons étanches aux brouillards entre le vetement et les éléments constitutifs tels que cagoules, gants, bottes, oculaires ou appareils de protection respiratoire, susceptibles d'etre spécifiés dans d'autres Normes européennes, comme par exemple les combinaisons une piece ou deux pieces, avec ou sans cagoule ou oculaire, avec ou sans bottes intégrées ou sur - bottes, avec ou sans gants ;
- vetements protégeant certaines parties du corps contre la perméation de produits chimiques, des liquides, par exemple blouses de laboratoires, vestes, pantalons, tabliers, manches, cagoules (sans arrivée d'air), etc. Ces vetements laissant une partie du corps sans protection, la présente norme spécifie uniquement les exigences de performance relatives au matériau du vetement et aux coutures.
NOTE Les vetements de protection chimique couvrant seulement une partie du corps et offrant seulement une protection contre la pénétration des produits chimiques liquides relevent du domaine d'application de l'EN 13034 (vetements de Type PB [6]).
Varovalna obleka pred učinki tekočih kemikalij - Zahtevane lastnosti za obleko, neprepustno za vodo (tip 3), ali z zatesnjenimi spoji (tip 4), vključno z dodatki, ki zagotavljajo zaščito za posamezne dele telesa (tipa PB [3] in PB [4])
General Information
Relations
Standards Content (Sample)
SIST EN 14605:2005SLOVENSKIjulij 2005
STANDARDVarovalna obleka pred učinki tekočih kemikalij - Zahtevane lastnosti za obleko, neprepustno za vodo (tip 3), ali z zatesnjenimi spoji (tip 4), vključno z dodatki, ki zagotavljajo zaščito za posamezne dele telesa (tipa PB [3] in PB [4])Protective clothing against liquid chemicals - Performance requirements for clothing with liquid-tight (Type 3) or spray-tight (Type 4) connections, including items providing protection to parts of the body only (Types PB [3] and PB [4])©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaSIST EN 14605:2005(en)ICS13.340.10
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14605
March 2005 ICS 13.340.10 Supersedes EN 465:1995, EN 466:1995, EN 467:1995 English version
Protective clothing against liquid chemicals - Performance requirements for clothing with liquid-tight (Type 3) or spray-tight (Type 4) connections, including items providing protection to parts of the body only (Types PB [3] and PB [4])
Vêtements de protection contre les produits chimiques liquides - Exigences relatives aux vêtements dont les éléments de liaison sont étanches au liquide (Type 3) ou aux pulvérisations (Type 4), y compris les articles d'habillement qui protègent seulement certaines parties du corps (Types PB (3) et PB (4))
Schutzkleidung gegen flüssige Chemikalien - Leistungsanforderungen an Chemikalienschutzanzüge mit flüssigkeitsdichten (Typ 3) oder spraydichten (Typ 4) Verbindungen zwischen den Teilen der Kleidung, einschließlich der Kleidungsstücke, die nur einen Schutz für Teile des Körpers gewähren (Typen PB [3] und PB [4])This European Standard was approved by CEN on 14 February 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14605:2005: E
EN 14605:2005 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.5 4 Requirements.5 4.1 Materials.5 4.2 Seams, joins and assemblages.6 4.3 Performance requirements for whole suits (Types 3 and 4).6 4.3.1 General.6 4.3.2 Pre-conditioning.6 4.3.3 Conditioning.6 4.3.4 Resistance to penetration by liquids.7 4.4 Visor.8 4.4.1 General.8 4.4.2 Mechanical strength of visor.8 4.4.3 Field of vision.8 4.4.4 Distortion of vision.8 5 Marking.8 6 Information supplied by the manufacturer.9 Annex ZA (informative)
Relationship between this
European
Standard and the Essential Requirements
of EU Directive 89/686/EEC.11 Bibliography.12
EN 14605:2005 (E) 3 Foreword This document (EN 14605:2005) has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2005, and conflicting national standards shall be withdrawn at the latest by September 2005. This document supersedes EN 465:1995, EN 466:1995 and EN 467:1995. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 89/686/EEC. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. This document includes a Bibliography. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 14605:2005 (E) 4 1 Scope This document specifies the minimum requirements for the following types of limited use and reusable chemical protective clothing: Full-body protective clothing with liquid-tight connections between different parts of the clothing (Type 3: liquid-tight clothing) and, if applicable, with liquid-tight connections to component parts, such as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards.
Examples of such clothing are one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or over-boots, with or without gloves; Full-body protective clothing with spray-tight connections between different parts of the clothing (Type 4: spray-tight clothing) and, if applicable, spray-tight connections to component parts, such as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards.
Examples of such clothing are one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or over-boots, with or without gloves; Partial body protection garments offering protection to specific parts of the body against permeation of chemical liquids. Examples of such garments are e.g. laboratory coats, jackets, trousers, aprons, sleeves, hoods (not air-supplied) etc. As partial body protection leaves some parts of the body unprotected this document specifies only the performance requirements for the clothing material and the seams. NOTE Partial body chemical protective garments which offer only protection against penetration of chemical liquids are within the scope of EN 13034 (Type PB [6] clothing). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 340:2003, Protective clothing — General requirements. EN 463, Protective clothing - Protection against liquid chemicals - Test method: Determination of resistance to penetration by a jet of liquid (Jet Test). EN 468, Protective clothing - Protection against liquid chemicals - Test method: Determination of resistance to penetration by spray (Spray Test). EN 12941:1998, Respiratory protective devices - Powered filtering devices incorporating a helmet or a hood - Requirements, testing, marking. EN 14325:2003, Protective clothing against chemicals — Test methods and performance classification of chemical protective clothing materials, seams, joins and assemblages. EN 23758, Textiles - Care labelling code using symbols (ISO 3758:1991). EN 31092, Textiles — Determination of physiological properties — Measurement of thermal and water-vapour resistance under steady-state conditions (sweating guarded - hotplate test) (ISO 11092:1993). CEN ISO/TR 11610:2004, Protective clothing - Vocabulary (ISO/TR 11610:2004). ISO 7000, Graphical symbols for use on equipment — Index and synopsis.
EN 14605:2005 (E) 5 3 Terms and definitions For the purposes of this document, the terms and definitions given in CEN ISO/TR 11610:2004 apply. 4 Requirements 4.1 Materials Chemical protective clothing materials shall be tested according to the requirements of Table 1 and in accordance with the test methods specified in EN 14325. A performance level of at least 1 shall be obtained for all requirements. Chemical protective clothing materials shall not be known to cause skin irritation or have any adverse effect to health (see also EN 340:2003, 4.2). Prior to testing, all chemical protective clothing materials shall be cleaned, if the manufacturer's instructions indicate that cleaning is allowed. Manufacturer’s instructions with regard to number of cleaning cycles, cleaning procedures and possible reapplication of treatments shall be observed. If no maximum number of cleaning cycles is indicated, materials shall undergo five cycles. All test specimens shall be conditioned at (20 ± 2) °C and (65 ± 5) % relative humidity for at least 24 h and testing shall start within 5 min after removing the specimen from the conditioning atmosphere. Table 1 — Test requirements for Type 3, Type 4, Type PB [3] and Type PB [4] clothing Clause in
EN 14325:2003 Performance requirement 4.4 abrasion resistance 4.5 flex cracking resistance 4.6 a flex cracking resistance at –30 °C 4.7 tear resistance (trapezoidal) 4.9 tensile strength 4.10 puncture resistance 4.11 resistance to permeation of liquids 4.14 resistance to ignition a Only applicable to clothing intended for use at very low temperatures.
NOTE 1 Chemical protective clothing material, for which a test method in Table 1 does not provide a clear measurement end-point, should be marked "not applicable" in the test report and in the instructions for use. The reason why the test could not be completed should be indicated, e.g. where the elasticity of the specimen prevents to determine an end-point in the puncture resistance test. NOTE 2 Materials should be as light and as flexible as possible in order to ensure wearer comfort as well as providing effective protection. Material properties are only one element for the determination of wearer comfort of protective clothing. Design features of the clothing may even have a more important influence on wearer comfort than material properties.
EN 14605:2005 (E) 6 4.2 Seams, joins and assemblages Seams, joins and assemblages shall be tested and classified according to the requirements of Table 2 and the corresponding clauses of EN 14325. Table 2 — Requirements for seams, joins and assemblages of Type 3, Type 4, Type PB [3]a and
Type PB [4] clothing Performance requirement Reference resistance to permeation of liquids b EN 14325:2003, 4.11 resistance to penetration by liquids c EN 463 or
EN 468 seam strength EN 14325:2003, 5.5 a Seams, joins and assemblages of Type PB [3] clothing shall be tested to the jet test (EN 463). b Applicable only to seams which are exposed in use. For partial body protection items only seams relevant to the construction shall be considered and a performance level of at least 1 shall be obtained. c To be tested by whole suit tests, i.e. EN 463 (jet test) for Type 3 clothing and EN 468 (high level spray test) for Type 4 clothing.
4.3 Performance requirements for whole suits (Types 3 and 4) 4.3.1 General Chemical protective clothing shall fulfil the relevant requirements of EN 340. The clothing shall be made so that the wearer has freedom of movement and is as comfortable as possible, consistent with the protection afford
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.