SIST EN ISO 1110:2019
(Main)Plastics - Polyamides - Accelerated conditioning of test specimens (ISO 1110:2019)
Plastics - Polyamides - Accelerated conditioning of test specimens (ISO 1110:2019)
This document describes a method for the accelerated conditioning of test specimens of polyamides and
copolyamides. It is applicable to grades containing fillers and other additives, but not grades containing
more than a mass fraction of 2 % extractables.
The equilibrium moisture content attained by this method is close to the equilibrium moisture content
obtained in standard atmosphere 23 °C/50 %RH. The values of mechanical properties obtained after
accelerated conditioning in accordance with this method can differ slightly from those obtained after
conditioning in standard atmosphere 23 °C/50 %RH.
Kunststoffe - Polyamide - Beschleunigte Konditionierung von Probekörpern (ISO 1110:2019)
Dieses Dokument beschreibt ein Verfahren zum beschleunigten Konditionieren von Probekörpern aus Polyamiden und Copolyamiden. Sie eignet sich für Sorten, die Füllstoffe und andere Zusatzstoffe enthalten, aber nicht für Sorten, die mehr als 2 % (Massenanteil) an extrahierbaren Anteilen enthalten.
Der nach diesem Verfahren erreichte Gleichgewichtsfeuchtegehalt entspricht annähernd dem Gleichgewichtsfeuchtegehalt, der sich im Normklima 23 °C/50 % relativer Feuchte einstellt. Die mechanischen Eigenschaftswerte, die nach dem beschleunigten Konditionieren entsprechend diesem Verfahren erhalten wurden, können geringfügig von den nach der Konditionierung im Normklima 23 °C/50 % relativer Feuchte erhaltenen abweichen.
Plastiques - Polyamides - Conditionnement accéléré d'éprouvettes (ISO 1110:2019)
Le présent document décrit une méthode de conditionnement accéléré d'éprouvettes en polyamides et copolyamides. Il est applicable aux qualités contenant des charges et autres additifs, mais pas aux qualités contenant plus de 2 % (fraction massique) de matières extractibles.
Le taux d'humidité d'équilibre atteint par cette méthode correspond à peu près au taux d'humidité d'équilibre obtenu dans l'atmosphère normale 23 °C/50 %HR. Les valeurs de propriétés mécaniques obtenues après conditionnement accéléré selon cette méthode peuvent différer légèrement de celles obtenues après conditionnement dans l'atmosphère normale 23 °C/50 %HR.
Polimerni materiali - Poliamidi - Pospešeno kondicioniranje preskušancev (ISO 1110:2019)
Ta dokument opisuje metodo za pospešeno kondicioniranje poliamidnih in kopoliamidnih preskušancev. Uporablja se za razrede, ki vsebujejo polnila in druge dodatke, vendar ne za razrede, ki vsebujejo masni delež, večji od masnega deleža 2 % ekstrahiranih snovi.
Ravnotežna vsebnost vlage, dosežena s to metodo, je blizu ravnotežne vsebnosti vlage, dosežene v običajni atmosferi 23 °C/50 % relativne vlažnosti. Vrednosti mehanskih lastnosti, doseženih po pospešenem kondicioniranju v skladu s to metodo, se lahko nekoliko razlikujejo od vrednosti, doseženih po kondicioniranju v običajni atmosferi 23 °C/50 % relativne vlažnosti.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 1110:2019
01-september-2019
Nadomešča:
SIST EN ISO 1110:1999
Polimerni materiali - Poliamidi - Pospešeno kondicioniranje preskušancev (ISO
1110:2019)
Plastics - Polyamides - Accelerated conditioning of test specimens (ISO 1110:2019)
Kunststoffe - Polyamide - Beschleunigte Konditionierung von Probekörpern (ISO
1110:2019)
Plastiques - Polyamides - Conditionnement accéléré d'éprouvettes (ISO 1110:2019)
Ta slovenski standard je istoveten z: EN ISO 1110:2019
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 1110:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 1110:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 1110:2019
EN ISO 1110
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2019
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 1110:1997
English Version
Plastics - Polyamides - Accelerated conditioning of test
specimens (ISO 1110:2019)
Plastiques - Polyamides - Conditionnement accéléré Kunststoffe - Polyamide - Beschleunigte
d'éprouvettes (ISO 1110:2019) Konditionierung von Probekörpern (ISO 1110:2019)
This European Standard was approved by CEN on 22 December 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, North
Macedonia, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1110:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 1110:2019
EN ISO 1110:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 1110:2019
EN ISO 1110:2019 (E)
European foreword
This document (EN ISO 1110:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2019, and conflicting national standards
shall be withdrawn at the latest by December 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 1110:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 1110:2019 has been approved by CEN as EN ISO 1110:2019 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 1110:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 1110:2019
INTERNATIONAL ISO
STANDARD 1110
Fourth edition
2019-05
Plastics — Polyamides — Accelerated
conditioning of test specimens
Plastiques — Polyamides — Conditionnement accéléré d'éprouvettes
Reference number
ISO 1110:2019(E)
©
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 1110:2019
ISO 1110:2019(E)
COPYRIG
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.