SIST EN ISO 1873-2:2007
(Main)Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:2007)
Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:2007)
This part of ISO 1873 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of PP moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given. Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given. Properties and test methods which are suitable and necessary to characterize PP moulding and extrusion materials are listed. The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this part of ISO 1873, as are the designatory properties specified in Part 1. In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.
Kunststoffe - Polypropylen (PP)-Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 1873-2:2007)
Dieser Teil von ISO 1873 legt die Bedingungen zur Herstellung von Probekörpern und die zur Bestimmung der Eigenschaften von PP-Formmassen anzuwendenden Prüfverfahren fest. Anforderungen an die Hand¬habung des Probenmaterials und für das Konditionieren des Probenmaterials vor der Formgebung und der Probekörper vor der Prüfung sind ebenfalls enthalten.
Verfahren und Bedingungen für die Herstellung von Probekörpern und Vorschriften für die Bestimmung der Ei¬genschaften der Formmasse, aus der die Probekörper hergestellt werden, sind angegeben. Eigenschaften und Prüfverfahren, die geeignet und notwendig sind, um PP-Formmassen zu charakterisieren, sind aufge¬listet.
Die Eigenschaften wurden aus den in ISO 10350 1 angegebenen allgemeinen Prüfverfahren ausgewählt. Andere weithin gebräuchliche Prüfverfahren oder solche von besonderer Bedeutung für diese Formmassen, wie die kennzeichnenden Eigenschaften aus Teil 1 dieser Norm, sind in diesen Teil von ISO 1873 aufge¬nommen.
Um reproduzierbare und vergleichbare Prüfergebnisse zu erhalten, müssen die hier festgelegten Verfahren zur Probekörperherstellung und -konditionierung, Probekörpermaße sowie Prüfverfahren angewendet werden. Die gemessenen Werte müssen nicht notwendigerweise mit denen identisch sein, die bei Anwendung von Probekörpern mit anderen Maßen oder solchen, die mit einem anderen Verfahren hergestellt wurden, erhalten werden.
Plastiques - Polypropylene (PP) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 1873-2:2007)
L'ISO 1873-2:2007 spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai à appliquer pour déterminer les propriétés des polypropylènes (PP) pour moulage et extrusion. Elle indique les exigences requises lors de la manipulation du matériau pour essai, ainsi que lors de conditionnement dudit matériau avant moulage et des éprouvettes avant l'essai.
Elle précise les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesurage des propriétés des matériaux à partir desquels ces éprouvettes sont fabriquées. Elle fournit également une liste des propriétés et des méthodes d'essai appropriées et nécessaires à la caractérisation des polypropylènes pour moulage et extrusion.
Polimerni materiali - Polipropilenski (PP) materiali za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in določanje lastnosti (ISO 1873-2:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 1873-2:2007
01-november-2007
1DGRPHãþD
SIST EN ISO 1873-2:2000
SIST EN ISO 1873-2:2000/A1:2000
3ROLPHUQLPDWHULDOL3ROLSURSLOHQVNL 33 PDWHULDOL]DREOLNRYDQMHLQHNVWUXGLUDQMH
GHO 3ULSUDYDSUHVNXãDQFHYLQGRORþDQMHODVWQRVWL ,62
Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of
test specimens and determination of properties (ISO 1873-2:2007)
Kunststoffe - Polypropylen (PP)-Formmassen - Teil 2: Herstellung von Probekörpern und
Bestimmung von Eigenschaften (ISO 1873-2:2007)
Plastiques - Polypropylene (PP) pour moulage et extrusion - Partie 2: Préparation des
éprouvettes et détermination des propriétés (ISO 1873-2:2007)
Ta slovenski standard je istoveten z: EN ISO 1873-2:2007
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 1873-2:2007 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN ISO 1873-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2007
ICS 83.080.20 Supersedes EN ISO 1873-2:1997
English Version
Plastics - Polypropylene (PP) moulding and extrusion materials -
Part 2: Preparation of test specimens and determination of
properties (ISO 1873-2:2007)
Plastiques - Polypropylène (PP) pour moulage et extrusion Kunststoffe - Polypropylen (PP)-Formmassen - Teil 2:
- Partie 2: Préparation des éprouvettes et détermination Herstellung von Probekörpern und Bestimmung von
des propriétés (ISO 1873-2:2007) Eigenschaften (ISO 1873-2:2007)
This European Standard was approved by CEN on 27 August 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1873-2:2007: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN ISO 1873-2:2007 (E)
Contents Page
Foreword.3
2
---------------------- Page: 3 ----------------------
EN ISO 1873-2:2007 (E)
Foreword
This document (EN ISO 1873-2:2007) has been prepared by Technical Committee ISO/TC 61 "Plastics" in
collaboration with Technical Committee CEN/TC 249 "Plastics", the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2008, and conflicting national standards shall be withdrawn at
the latest by March 2008.
This document supersedes EN ISO 1873-2:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 1873-2:2007 has been approved by CEN as a EN ISO 1873-2:2007 without any modification.
3
---------------------- Page: 4 ----------------------
INTERNATIONAL ISO
STANDARD 1873-2
Third edition
2007-09-01
Plastics — Polypropylene (PP) moulding
and extrusion materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Polypropylène (PP) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 1873-2:2007(E)
©
ISO 2007
---------------------- Page: 5 ----------------------
ISO 1873-2:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 6 ----------------------
ISO 1873-2:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 1873-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 9, Thermoplastic
materials.
This third edition cancels and replaces the second edition (ISO 1873-2:1997), which has been technically
revised. It also incorporates the Amendment ISO 1873-2:1997/Amd.1:2000.
ISO 1873 consists of the following parts, under the general title Plastics — Polypropylene (PP) moulding and
extrusion materials:
⎯ Part 1: Designation system and basis for specifications
⎯ Part 2: Preparation of test specimens and determination of properties
© ISO 2007 – All rights reserved iii
---------------------- Page: 7 ----------------------
INTERNATIONAL STANDARD ISO 1873-2:2007(E)
Plastics — Polypropylene (PP) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and determination of properties
1 Scope
This part of ISO 1873 specifies the methods of preparation of test specimens and the test methods to be used
in determining the properties of PP moulding and extrusion materials. Requirements for handling test material
and for conditioning both the test material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of
the materials from which these specimens are made are given. Properties and test methods which are
suitable and necessary to characterize PP moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide
use for, or of particular significance to, these moulding and extrusion materials are also included in this part of
ISO 1873, as are the designatory properties specified in Part 1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation
and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will
not necessarily be identical to those obtained using specimens of different dimensions or prepared using
different procedures.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates
© ISO 2007 – All rights reserved 1
---------------------- Page: 8 ----------------------
ISO 1873-2:2007(E)
ISO 294-4, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4:
Determination of moulding shrinkage
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-1, Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 1133:2005, Plastics — Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate
(MVR) of thermoplastics
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pyknometer method and titration method
ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient
column method
ISO 1183-3, Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas
pyknometer method
ISO 1628-3, Plastics — Determination of the viscosity of polymers in dilute solution using capillary
viscometers — Part 3: Polyethylenes and polypropylenes
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 3167, Plastics — Multipurpose test specimens
ISO 4589-2, Plastics — Determination of burni
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.