SIST EN 3539:2010

Aerospace series - Nuts, anchor, self-locking, one lug, fixed, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C

This standard specifies the characteristics of one lug counterbored fixed anchor nuts, with a self-locking feature achieved by forming the upper portion out-of-round, in heat resisting steel, MoS2 lubricated. Classification: 1100 MPa / 315 °C.

Luft- und Raumfahrt - Annietmuttern, selbstsichernd, einseitiger Flansch, mit zylindrischer Aussenkung, aus hochwarmfestem Stahl, MoS2-geschmiert - Klasse: 1100 MPa (bei Raumtemperatur)/315 °C

Diese Norm legt die Merkmale von Annietmuttern mit zylindrischer Aussenkung und einseitigem Flansch, selbstsichernd durch ovale Formgebung des oberen Teils, aus hochwarmfestem Stahl, MoS2-geschmiert, fest.
Klasse: 1 100 MPa )/ 315 °C )

Série aérospatiale - Écrous à river, à freinage interne, fixes, simple patte, avec chambrage, en acier résistant à chaud, lubrifiés MoS2 - Classification: 1100 MPa (à température ambiante)/315 °C

Aeronavtika - Zakovne matice, samovarovalne, enostranske, fiksne, z izvrtino za valjaste vijake, iz toplotnoodpornega jekla, mazane z MoS2 - Klasifikacija: 1100 MPa (pri temperaturi okolice)/315 °C

Ta standard določa značilnosti enostranskih fiksnih zakovnih matic, z izvrtino za vijake, s samozapiranjem, ki je omogočeno tako, da je zgornji del oblikovan ovalno, iz toplotnoodpornega jekla, mazanih z MoS2. Klasifikacija: 1.100 MPa (pri temperaturi okolice)/315 °C.

General Information

• Status: Published
• Publication Date: 07-Mar-2010
• ICS: 49.030.30 - Nuts
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Mar-2010
• Due Date: 06-May-2010
• Completion Date: 08-Mar-2010
• Ref Project: EN 3539:2010 - Aerospace series - Nuts, anchor, self-locking, one lug, fixed, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Zakovne matice, samovarovalne, enostranske, fiksne, z izvrtino za valjaste vijake, iz toplotnoodpornega jekla, mazane z MoS2 - Klasifikacija: 1100 MPa (pri temperaturi okolice)/315 °CLuft- und Raumfahrt - Annietmuttern, selbstsichernd, einseitiger Flansch, mit zylindrischer Aussenkung, aus hochwarmfestem Stahl, MoS2-geschmiert - Klasse: 1100
MPa (bei Raumtemperatur)/315 °CSérie aérospatiale - Écrous à river, à freinage interne, fixes, simple patte, avec chambrage, en acier résistant à chaud, lubrifiés MoS2 - Classification: 1100 MPa (à température ambiante)/315 °CAerospace series - Nuts, anchor, self-locking, one lug, fixed, with counterbore, in heat resisting steel, MoS2 lubricated - Classification: 1100 MPa (at ambient temperature)/315 °C49.030.30MaticeNutsICS:Ta slovenski standard je istoveten z:EN 3539:2010SIST EN 3539:2010en,de01-april-2010SIST EN 3539:2010SLOVENSKI
STANDARD



SIST EN 3539:2010



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3539
February 2010 ICS 49.030.30 English Version
Aerospace series - Nuts, anchor, self-locking, one lug, fixed, with counterbore, in heat resisting steel,
MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature) / 315 °C
Série aérospatiale - Écrous à river, à freinage interne, fixes, simple patte, avec chambrage, en acier résistant à chaud, lubrifiés MoS2 - Classification : 1 100 MPa (à température ambiante) / 315 °C
Luft- und Raumfahrt - Annietmuttern, selbstsichernd, einseitiger Flansch, mit zylindrischer Aussenkung, aus hochwarmfestem Stahl,
MoS2-geschmiert - Klasse: 1 100
MPa (bei Raumtemperatur) / 315 °C This European Standard was approved by CEN on 18 December 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3539:2010: ESIST EN 3539:2010



EN 3539:2010 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Required characteristics .54Designation .75Marking .86Technical specification .8 SIST EN 3539:2010



EN 3539:2010 (E) 3 Foreword This document (EN 3539:2010) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 2010, and conflicting national standards shall be withdrawn at the latest by August 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembour
...