iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 28662-3:2000/A1:2000

(Amendment)

Hand-held portable power tools - Measurement of vibrations at the handle - Part 3: Rock drills and rotary hammers - Amendment A1 (ISO 8662-3:1992)

Hand-held portable power tools - Measurement of vibrations at the handle - Part 3: Rock drills and rotary hammers - Amendment A1 (ISO 8662-3:1992)

Supplements ISO 8662-1 and describes a type test procedure for establishing the magnitude of vibration in the handle of rock drills and rotary hammers. The power tools covered may be electrically, pneumatically or hydraulically driven, or driven by means of an internal combustion engine. Annex A gives a definition of the basicentric coordinate system, Annex B a model test report.

Handgehaltene motorbetriebene Maschinen - Messung mechanischer Schwingungen am Handgriff - Teil 3: Gesteinsbohrmaschinen und Bohrhämmer (ISO 8662-3:1992)

Machines a moteur portatives - Mesurage des vibrations au niveau des poignées - Partie 3: Marteaux perforateurs et marteaux rotatifs (ISO 8662-3:1992)

Hand-held portable power tools - Measurement of vibrations at the handle - Part 3: Rock drills and rotary hammers - Amendment A1 (ISO 8662-3:1992)

General Information

Status
Withdrawn
Publication Date
31-Mar-2000
Withdrawal Date
23-Nov-2011
ICS
13.160 - Vibration and shock with respect to human beings
25.140.01 - Hand-held tools in general
Technical Committee
SS SPL - Technical Board for the general field
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
22-Nov-2011
Due Date
15-Dec-2011
Completion Date
24-Nov-2011
Directive
89/392/EEC - Machinery - Safety of machinery: general essential health and safety requirements
98/37/EC - Machinery
Mandate
M/BC/CEN/88/13 - Standardization request to CEN/CENELEC relating to machinery
Ref Project
EN 28662-3:1994/A1:1995 - Hand-held portable power tools - Measurement of vibrations at the handle - Part 3: Rock drills and rotary hammers (ISO 8662-3:1992)

Relations

Replaced By
SIST EN ISO 28927-10:2012 - Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 10: Percussive drills, hammers and breakers (ISO 28927-10:2011)
Effective Date
01-Jan-2012
Amends
SIST EN 28662-3:2000 - Hand-held portable power tools - Measurement of vibrations at the handle - Part 3: Rock drills and rotary hammers (ISO 8662-3:1992)
Effective Date
22-Dec-2008

Buy Standard

EN 28662-3:2000/A1:2000EN 28662-3:2000/A1:2000
PreviousNext
Amendment
EN 28662-3:2000/A1:2000
English language
3 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 28662-3:2000/A1:2000
01-april-2000
Hand-held portable power tools - Measurement of vibrations at the handle - Part 3:
Rock drills and rotary hammers - Amendment A1 (ISO 8662-3:1992)
Hand-held portable power tools - Measurement of vibrations at the handle - Part 3: Rock
drills and rotary hammers - Amendment A1 (ISO 8662-3:1992)
Handgehaltene motorbetriebene Maschinen - Messung mechanischer Schwingungen am
Handgriff - Teil 3: Gesteinsbohrmaschinen und Bohrhämmer (ISO 8662-3:1992)
Machines a moteur portatives - Mesurage des vibrations au niveau des poignées - Partie
3: Marteaux perforateurs et marteaux rotatifs (ISO 8662-3:1992)
Ta slovenski standard je istoveten z: EN 28662-3:1994
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 28927-13:2022(Main)
Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 13: Fastener driving tools (ISO 28927-13:2022)
EN ISO 28927-13:2022

This document specifies a laboratory method for measuring the vibration at the handle of fastener
driving tools. It is a type test procedure for establishing the vibration value on the handle of a handheld power tool operating under a specified load.
This document is applicable to fastener driving tools driven pneumatically or by other means, using
nails, staples or pins.
This document is applicable to tools with single sequential actuation, contact actuation, contact
actuation with automatic reversion or continual contact actuation (see Figures 1 to 3).
This document is not applicable to tools operating in full sequential mode due to their much longer
intervals in between individual actuations. However, to provide an indication for comparison of
different tools of this type (see Figures 4 and 5), Annex C provides informative guidance.
NOTE Today current knowledge does not allow any conclusions regarding physiological and pathological
effects between isolated shocks and continuous shock sequences, and their repetition rates

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28927-8:2010/A2:2019(Amendment)
Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 8: Saws, polishing and filing machines with reciprocating action and small saws with oscillating or rotating action - Amendment 2: Oscillating knives (vibrating screen removal tools) (ISO 28927-8:2009/Amd 2:2019)
EN ISO 28927-8:2009/A2:2019
  • Amendment
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28927-8:2010/A1:2016(Amendment)
Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 8: Saws, polishing and filing machines with reciprocating action and small saws with oscillating or rotating action - Amendment 1: Polishing machines, modified feed forces (ISO 28927-8:2009/Amd 1:2015)
EN ISO 28927-8:2009/A1:2015

2013-09-20 EMA: Draft for //ENQ received in ISO/CS (see notification of 2013-09-19 in dataservice).

  • Amendment
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28927-5:2010/A1:2015(Amendment)
Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 5: Drills and impact drills (ISO 28927-5:2009/Amd 1:2015)
EN ISO 28927-5:2009/A1:2015

2013-10-02 EMA: Draft for //ENQ received in ISO/CS (see notification of 2013-10-02 in dataservice).

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 20643:2008/A1:2013(Amendment)
Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission - Amendment 1: Accelerometer positions (ISO 20643:2005/Amd 1:2012)
EN ISO 20643:2008/A1:2012

This document provides the basis for the drafting of vibration test codes for hand-held and hand-guided powerdriven machinery. It specifies the determination of hand-transmitted vibration emission in terms of frequencyweighted root-mean-square (r.m.s.) acceleration during type testing. For machines where vibration test codes do not exist, it may also be used for determination of emission values and contains sufficient guidance for designing an appropriate test. NOTE Vibration test codes based on this document should define measuring procedures which provide controlled, repeatable and reproducible results which are, as far as possible, in agreement with the vibration values measured at the machine-hand contact surfaces under real working conditions and for which the uncertainties of measurement are quantified. This document is applicable to hand-held power tools (e.g. chipping hammers, sanders), hand-guided powered machines (e.g. lawn mowers, single-axle tractors, vibratory rollers) and other types of powered machines fitted with handles, guiding beams or similar means of control. It is applicable to machinery of all power sources (electrical, hydraulic, pneumatic, internal combustion engine, etc.). It does not apply to fixed machinery in which the vibration is transmitted to the hands of the user through the workpiece. This document is not applicable to vibration transmitted from steering wheels or control levers of mobile machinery where the operator's position is on the machine, see EN 1032. It is restricted to translational vibration measured in three orthogonal directions at the hand-machine interface. This document should be applied with caution to machines producing single and repetitive shocks with a frequency of occurrence lower than 5 Hz. For such machines, it is not known whether frequency-weighted root-mean-square acceleration values are related to the risks to health and additional measurements may be required. When developing vibration test codes for such machines the information in CEN ISO/TS 15694 should be considered. This document is not applicable to vibration test codes published before the date of publication of this document by CEN and, when used as test code, to hand-held and hand-guided machinery manufactured before that date. This document does not present limits or recommended vibration values. It does not give any guidance or recommendations for determination of human exposure to vibration at the workplace. For such information, reference is made to EN ISO 5349-1 and EN ISO 5349-2.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28927-10:2012(Main)
Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 10: Percussive drills, hammers and breakers (ISO 28927-10:2011)
EN ISO 28927-10:2011

ISO 28927-10:2011 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held power driven percussive machines with and without rotary action [portable rock drills, plug hole drills, rotary hammers, breakers (e.g. pavement breakers, concrete breakers or road breakers), riveting hammers, chipping hammers, pick hammers or similar]. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine fitted with an inserted tool bit.
ISO 28927-10:2011 is applicable to hand-held machines, driven pneumatically or by other means, intended for making holes in hard materials, such as rock and concrete. It is also applicable to breakers intended to work downwards to break hard materials (concrete, rock, pavement, asphalt, etc.) and for hammers intended to work in any direction to perform riveting or chiselling work. It is not applicable to impact drills with direct mechanical impact mechanisms. ISO 28927-10:2011 is not applicable to jack leg type rock drills and push feed rock drills, which are hand guided (the feed force is not applied by hand, but by an additional device).

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28927-11:2011(Main)
Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 11: Stone hammers (ISO 28927-11:2011)
EN ISO 28927-11:2011

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held stone hammers. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a stone hammer when operated in laboratory conditions. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to engraving pens and stone hammers intended for use by stone masons, driven pneumatically or by other means. It is not applicable to demolition hammers or to chipping hammers primarily intended for use on metal or in construction.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28927-8:2010(Main)
Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 8: Saws, polishing and filing machines with reciprocating action and saws with oscillating or rotating action (ISO 28927-8:2009)
EN ISO 28927-8:2009

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven saws, polishing and filing machines with reciprocating action and small saws with oscillating or rotating action. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to reciprocating files intended for surface finishing equipped with a file or polishing tool, saws intended for parting sheets, plaster for medical use or wood, or equipped with a saw blade for use on all kinds of materials, and small circular saws primarily intended for cutting metal or composite materials (see Clause 5), whether driven pneumatically or by other means. It is not applicable to files that are normally used with one hand on the file blade, nor to large circular saws intended for cutting wood.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28927-7:2010(Main)
Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 7: Nibblers and shears (ISO 28927-7:2009)
EN ISO 28927-7:2009

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven nibblers and shears. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a machine run under specified test conditions. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to nibblers and shears (see Clause 5), driven pneumatically or by other means, intended for cutting sheet metal or composite materials.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 28927-5:2010(Main)
Hand-held portable power tools - Test methods for evaluation of vibration emission - Part 5: Drills and impact drills (ISO 28927-5:2009)
EN ISO 28927-5:2009

This part of ISO 28927 specifies a laboratory method for measuring hand-transmitted vibration emission at the handles of hand-held, power-driven drills and impact drills. It is a type-test procedure for establishing the magnitude of vibration in the gripping areas of a drill fitted with a drill bit. It is intended that the results be used to compare different models of the same type of machine. This part of ISO 28927 is applicable to straight drills, drills with a pistol-grip and angle drills intended for drilling holes with rotating or impact action in all kinds of materials (see Clause 5), driven pneumatically or by other means. It is not applicable to heavy-duty drills with a screw feed or drills driven by a combustion engine.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day