SIST EN 4840-101:2018

Aerospace series - Heat shrinkable moulded shapes - Part 101: Polyolefin, semi-rigid, limited fire hazard - Temperature range - 30 °C to 105 °C - Product standard

This European Standard specifies the required characteristics for heat-shrinkable polyolefin semi-rigid, limited fire hazard heat-shrinkable boots for use in aircraft electrical systems at operating temperatures between - 30 °C and 105 °C.
The moulded shapes may be supplied with a pre-coated adhesive. Refer to the manufacturers/suppliers for options. A guide to adhesive compatibility is given in Annex A.
These moulded shapes are normally supplied in the styles and dimensions given in EN 4840-002 Tables 1 to 22. The colour is normally black.
Styles and dimensions other than those specifically listed in EN 4840-002 Tables 1 to 22 may be available as custom items. These items shall be considered to comply with this standard if they comply with the property requirements listed in Table 1 with the exception of dimensions.

Luft- und Raumfahrt - Wärmeschrumpfende Bauteile - Teil 101: Polyolefin, halbsteif, reduziertes Brandverhalten - Temperaturbereich - 30 °C bis 105 °C - Produktnormen

Série aérospatiale - Manchons thermorétractables - Partie 101 : Semi-rigides en polyoléfine, à risque de feu limité - Température - 30 °C à 105 °C - Norme de produit

Aeronavtika - Toplotno skrčljive brizgane forme - 101. del: Poliolefin, poltogi, z majhno požarno nevarnostjo - Temperaturno območje - 30 °C do 105 °C - Standard za proizvod

Ta evropski standard določa zahtevane lastnosti za toplotno skrčljive škornje iz poltogega poliolefina z omejeno požarno nevarnostjo za uporabo v letalskih električnih sistemih pri delovni temperaturi med −30 °C in 105 °C.
Brizgane forme so lahko predhodno premazane z lepilom. Za možnosti se je treba obrniti na proizvajalca/dobavitelja. Vodnik po združljivosti lepil je podan v dodatku A.
Te brizgane forme so običajno dobavljene v slogih in z dimenzijami, podanimi v standardu EN 4840-002, preglednice od 1 do 22. Običajno so črne barve.
Slogi in dimenzije, ki niso posebej navedeni v standardu EN 4840-002, preglednice od 1 do 22, so morda na voljo kot elementi po meri. Ti elementi bodo obravnavani kot skladni s tem standardom, če so skladni z zahtevami za lastnosti, navedenimi v preglednici 1, razen z zahtevami za dimenzije.

General Information

• Status: Published
• Publication Date: 16-Oct-2018
• ICS: 49.025.40 - Rubber and plastics
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 24-Aug-2018
• Due Date: 29-Oct-2018
• Completion Date: 17-Oct-2018
• Ref Project: EN 4840-101:2018 - Aerospace series - Heat shrinkable moulded shapes - Part 101: Polyolefin, semi-rigid, limited fire hazard - Temperature range - 30 °C to 105 °C - Product standard

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 4840-101:2018
01-november-2018
$HURQDYWLND7RSORWQRVNUþOMLYHEUL]JDQHIRUPHGHO3ROLROHILQSROWRJL]
PDMKQRSRåDUQRQHYDUQRVWMR7HPSHUDWXUQRREPRþMHƒ&GRƒ&6WDQGDUG
]DSURL]YRG
Aerospace series - Heat shrinkable moulded shapes - Part 101: Polyolefin, semi-rigid,
limited fire hazard - Temperature range - 30 °C to 105 °C - Product standard
Luft- und Raumfahrt - Wärmeschrumpfende Bauteile - Teil 101: Polyolefin, halbsteif,
reduziertes Brandverhalten - Temperaturbereich - 30 °C bis 105 °C - Produktnormen
Série aérospatiale - Manchons thermorétractables - Partie 101 : Semi-rigides en
polyoléfine, à risque de feu limité - Température - 30 °C à 105 °C - Norme de produit
Ta slovenski standard je istoveten z: EN 4840-101:2018
ICS:
49.025.40 Guma in polimerni materiali Rubber and plastics
SIST EN 4840-101:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 4840-101:2018

---------------------- Page: 2 ----------------------

SIST EN 4840-101:2018


EN 4840-101
EUROPEAN STANDARD

NORME EUROPÉENNE

August 2018
EUROPÄISCHE NORM
ICS 49.060
English Version

Aerospace series - Heat shrinkable moulded shapes - Part
101: Polyolefin, semi-rigid, limited fire hazard -
Temperature range - 30 °C to 105 °C - Product standard
Série aérospatiale - Manchons thermorétractables - Luft- und Raumfahrt - Wärmeschrumpfende Formteile
Partie 101 : Semi-rigides en polyoléfine, à risque de feu - Teil 101: Polyolefin, halbsteif, reduziertes
limité - Température - 30 °C à 105 °C - Norme de Brandverhalten - Temperaturbereich - 30 °C bis 105 °C
produit - Produktnormen
This European Standard was approved by CEN on 20 May 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4840-101:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 4840-101:2018
EN 4840-101:2018 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 5
4 Required characteristics . 5
5 Quality assurance . 9
6 Designation . 10
7 Labelling and packaging . 10
8 Technical specification . 10
Annex A (informative) Adhesive compatibility guide for EN 4840-101 moulded shapes . 11

2

---------------------- Page: 4 ----------------------

SIST EN 4840-101:2018
EN 4840-101:2018 (E)
European foreword
This document (EN 4840-101:2018) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by February 2019, and conflicting national standards shall
be withdrawn at the latest by February 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST EN 4840-101:2018
EN 4840-101:2018 (E)
1 Scope
This European Standard specifies the required characteristics for heat-shrinkable polyolefin semi-rigid,
limited fire hazard heat-shrinkable boots for use in aircraft electrical systems at operating temperatures
between − 30 °C and 105 °C.
The moulded shapes may be supplied with a pre-coated adhesive. Refer to the manufacturers/suppliers
for options. A guide to adhesive compatibility is given in Annex A.
These moulded shapes are normally supplied in the styles and dimensions given in EN 4840-002 Tables 1
to 22. The colour is normally black.
Styles and dimensions other than those specifically listed in EN 4840-002 Tables 1 to 22 may be available
as custom items. These items shall be considered to comply with this standard if they comply with the
property requirements listed in Table 1 with the exception of dimensions.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 3909, Aerospace series — Test fluids and test methods for electrical and optical components and
sub-assemblies
EN 4708-106, Aerospace series — Sleeving, heat-shrinkable, for binding, insulation and identification —
1)
Part 106: Limited fire hazard sleeving — Operating temperature ‒ 30 °C to 105 °C — Product standard
EN 4840-001, Aerospace series — Heat shrinkable moulded shapes — Part 001: Technical specification
EN 4840-002, Aerospace series — Heat shrinkable moulded shapes — Part 002: Index of product standards
1)
and product dimensions
2)
IEC 60684-3, Flexible insulating sleeving — Part 3: Specifications for individual types of sleeving
IEC 60695-11-10, Fire hazard testing — Part 11-10: Test flames — 50 W horizontal and vertical flame test
2)
methods
2)
IEC 62329-1, Heat shrinkable moulded shapes — Part 1: Definitions and general requirements
2)
IEC 62329-2, Heat-shrinkable moulded shapes — Part 2: Methods of test
2)
IEC 60757:1983, Code for designation of colours
3)
ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids

1) Published as ASD-STAN Prestandard at the date of publication of this European Standard by AeroSpace and
Defence industries Association of Europe - Standardization (ASD-STAN), http://www.asd-stan.org/
2) Published by: International Electrotechnical Com
...