Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up to 2 W and in the band 915 MHz to 921 MHz with power levels up to 4 W - Harmonised Standard for access to radio spectrum

The present document specifies technical characteristics and methods of measurements for Radio Frequency
Identification (RFID) devices used in the frequency band 865 MHz to 868 MHz and 915 MHz to 921 MHz.
Power limits up to a maximum of 2 W e.r.p. are specified for this equipment in the frequency band 865 MHz to
868 MHz and up to a maximum of 4 W e.r.p. in the frequency band 915 MHz to 921 MHz.
NOTE 1: The term frequency band is used for reference to dedicated bands as described in ERC
Recommendation 70-03 [i.9], while frequency range is used in the other cases.
The frequency usage conditions for RFID are EU wide harmonised in the band 865 MHz to 868 MHz according to
Decision (EU) 2017/1483 [i.15] and in the band 915 MHz to 921 MHz according to Decision (EU) 2018/1538 [i.14].
According to Decision (EU) 2018/1538 [i.14], EU member states are requested to implement 3 channels only in the
915 MHz to 921 MHz band.
It should be noted that the frequency band 915 MHz to 921 MHz has only a limited implementation status within the
European Union and the CEPT countries. ERC Recommendation 70-03 [i.9] provides in appendix 1 an overview of
countries where the band is implemented.
The present document applies to RFID interrogators and tags operating together as a system. For each specified band,
multiple high power channels are made available for use by interrogators. The tags respond with a modulated signal
preferably in the adjacent low power channels. Interrogators may be used with either integral or external antennas.
The types of equipment covered by the present document are as follows:
• fixed interrogators;
• portable interrogators;
• batteryless tags;
• battery assisted tags;
• battery powered tags.
These types of radio equipment are capable of operating in the frequency ranges given in table 1 and table 2.
The present document contains requirements to demonstrate that the specified radio equipment both effectively uses and
supports the efficient use of radio spectrum in order to avoid harmful interference.
NOTE 2: The relationship between the present document and essential requirements of article 3.2 of
Directive 2014/53/EU [i.3] is given in annex A.

Oprema za radiofrekvenčno identifikacijo, ki deluje v pasu od 865 MHz do 868 MHz z močnostnimi nivoji do 2 W in v pasu od 915 MHz do 921 MHz z močnostnimi nivoji do 4 W - Harmonizirani standard za dostop do radijskega spektra

Ta dokument določa tehnične lastnosti in metode merjenja za naprave za radiofrekvenčno identifikacijo (RFID) v frekvenčnem pasu od 865 MHz do 868 MHz in od 915 MHz do 921 MHz.
Omejitve moči do največ 2 W efektivne sevane moči so za to opremo določene v frekvenčnem pasu od 865 MHz do 868 MHz in do največ 4 W efektivne sevane moči v frekvenčnem območju od 915 MHz do 921 MHz.
OPOMBA 1: Izraz frekvenčni pas se uporablja za sklicevanje na namenske pasove, opisane v priporočilu ERC 70-03 [i.9], frekvenčno območje pa se uporablja v drugih primerih.
Pogoji uporabe frekvenc za radiofrekvenčno identifikacijo so usklajeni v celotni Evropski uniji v pasu od 865 MHz do 868 MHz v skladu z Odločbo (EU) 2017/1483 [i.15], v pasu od 915 MHz do 921 MHz pa v skladu z Odločbo (EU) 2018/1538 [i.14].
V skladu z Odločbo (EU) 2018/1538 [i.14] morajo države članice EU izvesti samo 3 kanale v pasu od 915 MHz do 921 MHz.
Opozoriti je treba, da ima frekvenčni pas od 915 MHz do 921 MHz v Evropski uniji in državah CEPT omejeno stanje izvajanja. V Dodatku 1 Priporočila ERC 70-03 [i.9] je pregled držav, v katerih je pas izveden.
Ta dokument se uporablja za čitalnike in odzivnike za radiofrekvenčno identifikacijo, ki skupaj delujejo kot sistem. Za vsak določen pas je za čitalnike na voljo več kanalov z visoko močjo. Odzivniki odgovarjajo z moduliranim signalom, če je mogoče, v sosednjih kanalih manjših moči. Čitalniki se lahko uporabljajo z vgrajenimi ali zunanjimi antenami.
Ta dokument zajema naslednje vrste opreme:
• fiksni čitalniki;
• prenosni čitalniki;
• odzivniki brez baterij;
• baterijsko podprti odzivniki;
• baterijsko napajani odzivniki.
Ti tipi radijske opreme lahko delujejo v frekvenčnih območjih, podanih v preglednici 1 in v preglednici 2.
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da navedena radijska oprema optimalno uporablja in podpira učinkovito rabo radijskega spektra z namenom preprečevanja škodljivih motenj.
OPOMBA 2: Razmerje med tem dokumentom in bistvenimi zahtevami iz člena 3.2
Direktive 2014/53/EU [i.3] je podano v dodatku A.

General Information

Status
Published
Public Enquiry End Date
31-Jul-2022
Publication Date
07-Jan-2024
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
03-Jan-2024
Due Date
09-Mar-2024
Completion Date
08-Jan-2024

Buy Standard

Standard
ETSI EN 302 208 V3.4.0 (2022-06) - Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up to 2 W and in the band 915 MHz to 921 MHz with power levels up to 4 W; Harmonised Standard for access to radio spectrum
English language
76 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 302 208 V3.4.1 (2023-10) - Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up to 2 W and in the band 915 MHz to 921 MHz with power levels up to 4 W; Harmonised Standard for access to radio spectrum
English language
71 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 302 208 V3.4.1 (2023-12) - Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up to 2 W and in the band 915 MHz to 921 MHz with power levels up to 4 W; Harmonised Standard for access to radio spectrum
English language
71 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
EN 302 208 V3.4.1:2024 - BARVE
English language
71 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

Draft ETSI EN 302 208 V3.4.0 (2022-06)






HARMONISED EUROPEAN STANDARD
Radio Frequency Identification Equipment operating in the
band 865 MHz to 868 MHz with power levels up to 2 W and
in the band 915 MHz to 921 MHz with power levels up to 4 W;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 208 V3.4.0 (2022-06)

Reference
REN/ERM-TG34-270
Keywords
harmonised standard, ID, radio, RFID, SRD

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2022.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 208 V3.4.0 (2022-06)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 9
1 Scope . 10
2 References . 10
2.1 Normative references . 10
2.2 Informative references . 11
3 Definition of terms, symbols and abbreviations . 12
3.1 Terms .
...

Final draft ETSI EN 302 208 V3.4.1 (2023-10)






HARMONISED EUROPEAN STANDARD
Radio Frequency Identification Equipment operating in the
band 865 MHz to 868 MHz with power levels up to 2 W and
in the band 915 MHz to 921 MHz with power levels up to 4 W;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 302 208 V3.4.1 (2023-10)

Reference
REN/ERM-TG34-270
Keywords
harmonised standard, ID, radio, RFID, SRD

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
https://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2023.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 302 208 V3.4.1 (2023-10)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms .
...

ETSI EN 302 208 V3.4.1 (2023-12)






HARMONISED EUROPEAN STANDARD
Radio Frequency Identification Equipment operating in the
band 865 MHz to 868 MHz with power levels up to 2 W and
in the band 915 MHz to 921 MHz with power levels up to 4 W;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 ETSI EN 302 208 V3.4.1 (2023-12)

Reference
REN/ERM-TG34-270
Keywords
harmonised standard, ID, radio, RFID, SRD

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
https://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2023.
All rights reserved.

ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 302 208 V3.4.1 (2023-12)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definition of terms, symbols and abbreviations . 11
3.1 Terms . 11
...

SLOVENSKI STANDARD
SIST EN 302 208 V3.4.1:2024
01-februar-2024
Oprema za radiofrekvenčno identifikacijo, ki deluje v pasu od 865 MHz do 868 MHz
z močnostnimi nivoji do 2 W in v pasu od 915 MHz do 921 MHz z močnostnimi
nivoji do 4 W - Harmonizirani standard za dostop do radijskega spektra
Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz
with power levels up to 2 W and in the band 915 MHz to 921 MHz with power levels up to
4 W - Harmonised Standard for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 302 208 V3.4.1 (2023-10)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
SIST EN 302 208 V3.4.1:2024 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 302 208 V3.4.1:2024

---------------------- Page: 2 ----------------------
SIST EN 302 208 V3.4.1:2024
ETSI EN 302 208 V3.4.1 (2023-12)






HARMONISED EUROPEAN STANDARD
Radio Frequency Identification Equipment operating in the
band 865 MHz to 868 MHz with power levels up to 2 W and
in the band 915 MHz to 921 MHz with power levels up to 4 W;
Harmonised Standard for access to radio spectrum

---------------------- Page: 3 ----------------------
SIST EN 302 208 V3.4.1:2024
 2 ETSI EN 302 208 V3.4.1 (2023-12)

Reference
REN/ERM-TG34-270
Keywords
harmonised standard, ID, radio, RFID, SRD

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871

Important notice
The present document can be downloaded from:
https://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.

Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2023.
All rights reserved.

ETSI

---------------------- Page: 4 ----------------------
SIST EN 302 208 V3.4.1:2024
 3 ETSI EN 302 208 V3.4.1 (2023-12)
Contents
Intellectual Property Rights . 7
Foreword . 7
Modal verbs terminology .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.