SIST EN ISO 11358-1:2014

Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-1:2014)

EN ISO 11358-1 specifies general conditions for the analysis of polymers using thermogravimetric techniques. It is applicable to liquids or solids. Solid materials may be in the form of pellets, granules or powders. Fabricated shapes reduced to appropriate specimen size may also be analysed by this method. Thermogravimetry can be used to determine the temperature(s) and rate(s) of decomposition of polymers, and to measure at the same time the amounts of volatile matter, additives and/or fillers they contain. The thermogravimetric measurements may be carried out in dynamic mode (mass change versus temperature or time under programmed conditions) or isothermal mode (mass change versus time at constant temperature). Thermogravimetric measurements may also be carried out using different testing atmospheres, e.g. to separate decomposition in an inert atmosphere from oxidative degradation.

Kunststoffe - Thermogravimetrie (TG) von Polymeren - Teil 1: Allgemeine Grundsätze (ISO 11358-1:2014)

Diese Internationale Norm legt allgemeine Bedingungen für die thermogravimetrische Analyse von Polymeren fest. Sie ist anwendbar auf flüssige und feste Stoffe. Die festen Stoffe können als Pellets, Granulat oder Pulver vorliegen. Mit dem Verfahren können ebenfalls auf eine geeignete Probekörpergröße reduzierte Fertigteile untersucht werden.
Die Thermogravimetrie kann zur Bestimmung der Temperatur(en) und der Zersetzungsrate(n) von Polymeren und zur gleichzeitigen Messung der Menge der darin enthaltenen flüchtigen Anteile, Zusatzstoffe und/oder Füllstoffe angewendet werden.
Thermogravimetrische Messungen können mit einem dynamischen Verfahren (Massenänderung in Abhängigkeit von der Temperatur oder Zeit unter programmierten Bedingungen) oder einem isothermen Verfahren (Massenänderung in Abhängigkeit von der Zeit bei konstanter Temperatur) durchgeführt werden.
Thermogravimetrische Messungen können ebenfalls unter Anwendung unterschiedlicher Prüfatmosphären durchgeführt werden, um beispielsweise die Zersetzung in einer inerten Atmosphäre von der oxidativen Zersetzung zu trennen.

Plastiques - Thermogravimétrie (TG) des polymères - Partie 1: Principes généraux (ISO 11358-1:2014)

L'ISO 11358-1:2014 spécifie les conditions générales d'analyse des polymères au moyen des techniques de thermogravimétrie. Elle est applicable aux liquides et aux solides. Les matériaux solides peuvent se présenter sous forme de granulés, de grains ou de poudre. Cette méthode d'analyse est également applicable aux objets façonnés sur lesquels une éprouvette de dimensions appropriées est prélevée.

Polimerni materiali - Termogravimetrija (TG) polimerov - 1. del: Splošna načela (ISO 11358-1:2014)

Standard EN ISO 11358-1 določa splošne pogoje za analizo polimerov z uporabo termogravimetrijskih tehnik. Uporablja se za tekočine ali trdne snovi. Trdni materiali imajo lahko obliko peletov, granul ali praškov. S to metodo se lahko analizira tudi izdelane oblikovance, prilagojene ustrezni velikosti preskušanca. S termogravimetrijo je mogoče določiti temperaturo(e) in stopnjo(e) razgradnje polimerov ter obenem izmeriti količine hlapnih snovi, aditivov in/ali polnil, ki jih polimeri vsebujejo. Termogravimetrijske meritve se lahko izvede dinamično (sprememba mase v primerjavi s temperaturo ali časom v programiranih razmerah) ali izotermno (sprememba mase v primerjavi s časom pri stalni temperaturi). Termogravimetrijske meritve se lahko izvede tudi v različnih preskusnih atmosferah, npr. da razgradnjo v inertni atmosferi zavarujete pred oksidativnim poslabšanjem.

General Information

• Status: Withdrawn
• Public Enquiry End Date: 19-May-2014
• Publication Date: 18-Aug-2014
• Withdrawal Date: 05-May-2022
• ICS: 83.080.01 - Plastics in general
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 05-May-2022
• Due Date: 28-May-2022
• Completion Date: 06-May-2022
• Ref Project: EN ISO 11358-1:2014 - Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-1:2014)

Relations

• Replaced By: SIST EN ISO 11358-1:2022 - Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-1:2022)
• Effective Date: 04-May-2022
• Replaces: SIST EN ISO 11358:1999 - Plastics - Thermogravimetry (TG) of polymers - General principles (ISO 11358:1997)
• Effective Date: 01-Oct-2014
• Revised: SIST EN ISO 11358-1:2022 - Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-1:2022)
• Effective Date: 27-Nov-2019

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11358-1:2014
01-oktober-2014
1DGRPHãþD
SIST EN ISO 11358:1999
3ROLPHUQLPDWHULDOL7HUPRJUDYLPHWULMD7*SROLPHURYGHO6SORãQDQDþHOD
,62
Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO 11358-
1:2014)
Kunststoffe - Thermogravimetrie (TG) von Polymeren - Teil 1: Allgemeine Grundsätze
(ISO 11358-1:2014)
Plastiques - Thermogravimétrie (TG) des polymères - Partie 1: Principes généraux (ISO
11358-1:2014)
Ta slovenski standard je istoveten z: EN ISO 11358-1:2014
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO 11358-1:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11358-1:2014

---------------------- Page: 2 ----------------------

SIST EN ISO 11358-1:2014

EUROPEAN STANDARD
EN ISO 11358-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
July 2014
ICS 83.080.01 Supersedes EN ISO 11358:1997
English Version
Plastics - Thermogravimetry (TG) of polymers - Part 1: General
principles (ISO 11358-1:2014)
Plastiques - Thermogravimétrie (TG) des polymères - Partie Kunststoffe - Thermogravimetrie (TG) von Polymeren - Teil
1: Principes généraux (ISO 11358-1:2014) 1: Allgemeine Grundsätze (ISO 11358-1:2014)
This European Standard was approved by CEN on 28 June 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11358-1:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11358-1:2014
EN ISO 11358-1:2014 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 11358-1:2014
EN ISO 11358-1:2014 (E)
Foreword
This document (EN ISO 11358-1:2014) has been prepared by Technical Committee ISO/TC 61 “Plastics” in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2015, and conflicting national standards shall be withdrawn at
the latest by January 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11358:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11358-1:2014 has been approved by CEN as EN ISO 11358-1:2014 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 11358-1:2014

---------------------- Page: 6 ----------------------

SIST EN ISO 11358-1:2014
INTERNATIONAL ISO
STANDARD 11358-1
First edition
2014-07-15
Plastics — Thermogravimetry (TG) of
polymers —
Part 1:
General principles
Plastiques — Thermogravimétrie (TG) des polymères —
Partie 1: Principes généraux
Reference number
ISO 11358-1:2014(E)
©
ISO 2014

---------------------- Page: 7 ----------------------

SIST EN ISO 11358-1:2014
ISO 11358-1:2014(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 11358-1:2014
ISO 11358-1:2014(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Test specimen preparation . 2
6.1 General . 2
6.2 Test specimens from finished products . 3
6.3 Test specimen conditioning . 3
6.4 Test specimen mass . 3
7 Calibration . 3
7.1 Mass calibration . 3
7.2 Temperature calibration . 3
8 Procedure. 4
8.1 General . 4
8.2 Temperature scanning mode . 4
8.3 Isothermal mode . 5
9 Expression of results . 5
9.1 Graphical representation . 5
9.2 Determination of increase in mass . 5
9.3 Determination of loss in mass . 6
10 Test report . 8
© ISO 2014 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 11358-1:2014
ISO 11358-1:2014(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any
patent rights identified during the development of the document will be in the Introduction and/or on
the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 5, Physical chemical
properties.
This first edition of ISO 11358-1 cancels and replaces ISO 11358:1997, which has been technically revised.
The main changes are:
a) addition of ISO 472 to the Normative references clause and removal of definitions specified therein;
b) revision of apparatus specifications.
ISO 11358 consists of the following parts, under the general title Plastics — Thermogravimetry (TG) of
polymers:
— Part 1: General principles
— Part 2: Determination of activation energy
— Part 3: Determination of the activation energy using the Ozawa-Friedman plot and analysis of the
reaction kinetics
iv © ISO 2014 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 11358-1:2014
INTERNATIONAL STANDARD ISO 11358-1:2014(E)
Plastics — Thermogravimetry (TG) of polymers —
Part 1:
General principles
1 Scope
This part of ISO 11358 specifies general conditions for the analysis of polymers using thermogravimetric
techniques. It is applicable to liquids or solids. Solid materials may be in the form of pellets, granules or
powders. Fabricated shapes reduced to appropriate specimen size may also be analysed by this method.
Thermogravimetry can be used to determine the temperature(s) and rate(s) of decomposition of
polymers, and to measure at the same time the amounts of volatile matter, additives and/or fillers they
contain.
The thermogravimetric measurements may be carried out in dynamic mode (mass change versus
temperature or time under programmed conditions) or isothermal mode (mass change versus time at
constant temperature).
Thermogravimetric measurements may also be carried out using different testing atmospheres, e.g. to
separate decomposition in an inert atmosphere from oxidative degradation.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 291, Plastics — Standard atmospheres for conditioning and testing
ISO 472, Plastics — Vocabulary
ISO 11357-1, Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 472 and the following apply.
3.1
dynamic mass-change determination
technique for recording the variation of the mass of a test specimen with temperature T which is
changing at a programmed rate
3.2
isothermal mass-change determination
technique for recording the variation of the mass of a test specimen with time t at
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Thermogravimetrie (TG) von Polymeren - Teil 1: Allgemeine Grundsätze (ISO/FDIS 11358-1:2014)Plastiques - Thermogravimétrie (TG) des polymères - Partie 1: Principes généraux (ISO/FDIS 11358-1:2014)Plastics - Thermogravimetry (TG) of polymers - Part 1: General principles (ISO/FDIS 11358-1:2014)83.080.01Polimerni materiali na splošnoPlastics in generalICS:Ta slovenski standard je istoveten z:FprEN ISO 11358-1 revkSIST FprEN ISO 11358-1:2014en,fr,de01-maj-2014kSIST FprEN ISO 11358-1:2014SLOVENSKI
STANDARD



kSIST FprEN ISO 11358-1:2014



© ISO 2014Plastics — Thermogravimetry (TG) of polymers —Part 1: General principlesPlastiques — Thermogravimétrie (TG) des polymères —Partie 1: Principes générauxINTERNATIONAL STANDARDPlease see the administrative notes on page iiiReference numberISO/FDIS 11358-1:2014(E)ISO/FDIS11358-1ISO/TC 61/SC 5Secretariat: DINVoting begins on: 2014-0Voting terminates on: 2014-0RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPOR TING DOCUMENTATION.IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STAN-DARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.FINALDRAFTkSIST FprEN ISO 11358-1:2014



ISO/FDIS 11358-1:2014(E) ii © ISO 2014 – All rights reservedCOPYRIGHT PROTECTED DOCUMENT©
ISO 2014All rights reservedä Unless otherwise speci Ðiedá no part of this publication may be reproduced or utilized otherwise in any form or by any meansá electronic or mechanicalá including photocopyingá or posting on the internet or an intranetá without prior written permissionä Permission can be requested from either ISO at the address below or ISOïs member body in the country of the requester.ISO copyright of ÐiceTel. + 41 22 749 01 11Fax + 41 22 749 09 47Eæmail copyright 7isoäorgWeb www.iso.orgPublished in SwitzerlandkSIST FprEN ISO 11358-1:2014



ISO/CEN PARALLEL PROCESSING-cessed under the ISO-lead mode of collaboration as de Ðined in the Vienna Agreementä The
Ðinal draft was established on the basis of comments received during a parallel enquiry on the draftäThis
Ðinal draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel two-month approval vote in ISO and formal vote in CEN.Positive votes shall not be accompanied by comments.Negative votes shall be accompanied by the relevant technical reasons.ISO/FDIS 11358-1:2014(E) © ISO 2014 – All rights reserved iiikSIST FprEN ISO 11358-1:2014



ISO/FDIS 11358-1:2014(E) iv © ISO 2014 – All rights reservedContents PageForeword .v1 Scope .12 Normative references .1uTermsanddeÐinitions .14 Principle .25 Apparatus .26 Test specimen preparation .26.1 General .2 xä t Test specimens from
Ðinished products .36.3 Test specimen conditioning .36.4 Test specimen mass .37 Calibration .37.1 Mass calibration .37.2 Temperature calibration .38 Procedure.48.1 General .48.2 Temperature scanning mode .48.3 Isothermal mode .59 Expression of results .59.1 Graphical representation .59.2 Determination of increase in mass .59.3 Determination of loss in mass .610 Test report .8Annex A (informative) Calibration materials for Curie-point temperature calibration .10Bibliography .11kSIST FprEN ISO 11358-1:2014



ISO/FDIS 11358-1:2014(E)Forewordthrough ISO technical committeesä Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizationsá governmental and nonægovernmentalá in liaison with ISOá also take part in the workä electrotechnical standardizationäThe procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be notedä This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rightsä ISO shall not be held responsible for identifying any or all such patent rightsä Details of any the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO speci Ðic terms and expressions related to conformity assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 5, Physical chemical properties.This
Ðirst edition of ISO
s s u w zæ s cancels and replaces ISO
s s u w zã s { { yá which has been technically revisedäThe main changes are: addition of ISO
v y t to the Normative references clause and removal of de Ðinitions speci Ðied thereinâ revision of apparatus speci ÐicationsäISO 11358 consists of the following parts, under the general title Plastics — Thermogravimetry (TG) of polymers:— Part 1: General principles— Part 2: Determination of activation energy— Part 3: Determination of the activation energy using the Ozawa-Friedman plot and analysis of the reaction kinetics © ISO 2014 – All rights reserved vkSIST FprEN ISO 11358-1:2014



kSIST FprEN ISO 11358-1:2014



Plastics — Thermogravimetry (TG) of polymers —Part 1: General principles1 ScopeThis part of ISO
s s u w z speci Ðies general conditions for the analysis of polymers using thermogravimetric techniquesä It is applicable to liquids or solidsä Solid materials may be in the form of pelletsá granules or powdersä Fabricated shapes reduced to appropriate specimen size may also be analysed by this methodäcontain.temperature or time under programmed conditions) or isothermal mode (mass change versus time at constant temperature).Thermogravimetric measurements may also be carried out using different testing atmospheresá eägä to separate decomposition in an inert atmosphere from oxidative degradation.2 Normative referencesThe following documentsá in whole or in partá are normatively referenced in this document and are indispensable for its applicationä For dated referencesá only the edition cited appliesä For undated ISO 291, Plastics — Standard atmospheres for conditioning and testingISO 472, Plastics — VocabularyISO 11357-1, Plastics — Differential scanning calorimetry (DSC) — Part 1: General principlesuTermsanddeÐinitionsFor the purposes of this documentá the terms and de Ðinitions given in ISO
v y t and the following applyä3.1dynamic mass-change determinationtechnique for recording the variation of the mass of a test specimen with temperature T which is changing at a programmed rate3.2isothermal mass-change determinationtechnique for recording the variation of the mass of a test specimen with time t at constant temperature T3.3Curie temperaturetemperature at which a ferromagnetic material passes from the ferromagnetic state to the paramagnetic state or vice versaFINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 11358-1:2014(E)© ISO 2014 – All rights reserved 1kSIST FprEN ISO 11358-1:2014



ISO/FDIS 11358-1:2014(E)4 PrincipleA test specimen is heated at speci Ðied rates with a controlled temperature programmeá and the change in mass is measured as a function of temperatureä Alternativelyá the specimen is kept at a given constant temperature and the change in mass is measured as a function of time over a given period.During measurement the test specimen is held in a controlled inert or oxidising atmosphere.In general, the reactions which cause the mass of a test specimen to change are decomposition or oxidation reactions or the volatilisation of a component. The change in mass is recorded as a thermogravimetric (TG) curve.The change in mass of a material as a function of temperature and the extent of this change are indicators of the thermal stability of the materialä TG data can therefore be used to evaluate the relative thermal stability of polymers of the same generic family and polymeræpolymer or polymeræadditive interactionsá using measurements made under the same test conditions.NOTE TG data may be used for process controlá process development and material evaluationä Longæterm thermal stability is a complex function of service and environmental condition
...