SIST EN ISO 13225:2012
(Main)Geometrical product specifications (GPS) - Dimensional measuring equipment; Height gauges - Design and metrological characteristics (ISO 13225:2012)
Geometrical product specifications (GPS) - Dimensional measuring equipment; Height gauges - Design and metrological characteristics (ISO 13225:2012)
This International Standard specifies the most important design and metrological characteristics of height
gauges (with analogue indication or digital indication) for linear-dimensional measurements perpendicular to a
surface plate.
Geometrische Produktspezifikation (GPS) - Längenmessgeräte: Vertikale Längenmessgeräte - Konstruktionsmerkmale und messtechnische Merkmale (ISO 13225:2012)
Diese Internationale Norm legt die wichtigsten Konstruktionsmerkmale und messtechnischen Merkmale für vertikale Längenmessgeräte (mit Skalen oder Ziffernanzeige) für Längenmessungen senkrecht zu einer Prüfplatte fest.
Spécification géométrique des produits (GPS) - Équipement de mesurage dimensionnel; Mesureurs verticaux - Caractéristiques de conception et caractéristiques métrologiques (ISO 13225:2012)
La présente Norme internationale spécifie les caractéristiques de conception et les caractéristiques
métrologiques les plus importantes des mesureurs verticaux (avec indication analogique ou indication
numérique) pour les mesurages dimensionnels linéaires perpendiculairement à un marbre.
Specifikacija geometrijskih veličin izdelka - Merilni instrumenti za merjenje dolžin - Merilni instrumenti za merjenje višin - Konstrukcijske in meroslovne značilnosti (ISO 13225:2012)
Ta mednarodni standard določa najpomembnejše konstrukcijske in metrološke značilnosti merilnih instrumentov za merjenje višin (z analognim ali digitalnim prikazom) za merjenje višin pravokotno na ravno merilno ploščo.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2012
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND0HULOQLLQVWUXPHQWL]DPHUMHQMHGROåLQ
0HULOQLLQVWUXPHQWL]DPHUMHQMHYLãLQ.RQVWUXNFLMVNHLQPHURVORYQH]QDþLOQRVWL
,62
Geometrical product specifications (GPS) - Dimensional measuring equipment; Height
gauges - Design and metrological characteristics (ISO 13225:2012)
Geometrische Produktspezifikation (GPS) - Längenmessgeräte: Vertikale
Längenmessgeräte - Konstruktionsmerkmale und messtechnische Merkmale (ISO
13225:2012)
Spécification géométrique des produits (GPS) - Équipement de mesurage dimensionnel;
Mesureurs verticaux - Caractéristiques de conception et caractéristiques métrologiques
(ISO 13225:2012)
Ta slovenski standard je istoveten z: EN ISO 13225:2012
ICS:
17.040.30 Merila Measuring instruments
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND*36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 13225
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2012
ICS 17.040.30
English Version
Geometrical product specifications (GPS) - Dimensional
measuring equipment; Height gauges - Design and metrological
characteristics (ISO 13225:2012)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) -
Équipement de mesurage dimensionnel; Mesureurs Längenmessgeräte: Vertikale Längenmessgeräte -
verticaux - Caractéristiques de conception et Konstruktionsmerkmale und messtechnische Merkmale
caractéristiques métrologiques (ISO 13225:2012) (ISO 13225:2012)
This European Standard was approved by CEN on 16 March 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13225:2012: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 13225:2012) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2012, and conflicting national standards shall be withdrawn
at the latest by November 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 13225:2012 has been approved by CEN as a EN ISO 13225:2012 without any modification.
INTERNATIONAL ISO
STANDARD 13225
First edition
2012-05-01
Geometrical product specifications
(GPS) — Dimensional measuring
equipment; Height gauges — Design and
metrological characteristics
Spécification géométrique des produits (GPS) — Équipement de
mesurage dimensionnel; Mesureurs verticaux — Caractéristiques de
conception et caractéristiques métrologiques
Reference number
ISO 13225:2012(E)
©
ISO 2012
ISO 13225:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 13225:2012(E)
Contents Page
Foreword .iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Design characteristics . 2
4.1 General design and nomenclature . 2
4.2 Main dimensions . 5
4.3 Types of indicating devices . 6
4.4 Protection for field use .10
4.5 Measuring and scribing stylus .10
4.6 Instrument base .10
4.7 Design characteristics (manufacturer’s specification) .10
5 Metrological characteristics . 11
5.1 General . 11
5.2 Operating conditions . 11
5.3 Effect of slider locking . 11
5.4 Definition of metrological characteristics (limited by MPE) . 11
6 Proving of conformance with specifications .12
6.1 General .12
6.2 Measurement standards for the calibration of metrological characteristics .12
7 Marking .12
Annex A (informative) Error tests .14
Annex B (informative) Data sheet (Example) .19
Annex C (informative) Calibration of metrological characteristics .20
Annex D (informative) Relation to the GPS matrix model .21
Bibliography .23
ISO 13225:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13225 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
iv © ISO 2012 – All rights reserved
ISO 13225:2012(E)
Introduction
This International Standard is a geometrical product specification (GPS) standard and is to be regarded as a general
GPS standard (see ISO/TR 14638). It influences the chain link 5 of the chain of standards on size and distance.
The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this
document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and the
default decision rules given in ISO 14253-1 apply to specifications made in accordance with this document,
unless otherwise indicated.
For more detailed information of the relation of this International Standard to the GPS matrix model, see Annex D.
This International Standard is intended to serve the purpose of promoting
— the relationship between the manufacturer and purchaser, and
— the management of measuring instruments in the quality-assurance system.
INTERNATIONAL STANDARD ISO 13225:2012(E)
Geometrical product specifications (GPS) — Dimensional
measuring equipment; Height gauges — Design and
metrological characteristics
1 Scope
This International Standard specifies the most important design and metrological characteristics of height
gauges (with analogue indication or digital indication) for linear-dimensional measurements perpendicular to a
surface plate.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the cited editions apply. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 1:2002, Geometrical Product Specifications (GPS) — Standard reference temperature for geometrical
product specification and verification
ISO 14253-1, Geometrical product specifications (GPS) — Inspection by measurement of workpieces and
measuring equipment — Part 1: Decision rules for proving conformance or non-conformance with specifications
ISO 14253-2, Geometrical product specifications (GPS) — Inspection by measurement of workpieces and
measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration
of measuring equipment and in product verification
ISO 14978:2006, Geometrical product specifications (GPS) — General concepts and requirements for GPS
measuring equipm
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.