SIST EN ISO 5463:2024

Geometrical product specifications (GPS) - Form measuring equipment; Rotary axis form measuring instruments - Design and metrological characteristics (ISO 5463:2024)

This document specifies the most important design and metrological characteristics of rotary axis form measuring instruments.
It is not applicable to coordinate measurement systems as defined by ISO 10360, whether they are fitted with a rotary axis or not, except with special agreement.

Geometrische Produktspezifikationen (GPS) - Formmessgeräte; Formmessgeräte mit Drehachse - Konstruktion und messtechnische Eigenschaften (ISO 5463:2024)

Dieses Dokument legt die wichtigsten Konstruktionsmerkmale und messtechnischen Eigenschaften von Formmessgeräten mit Drehachsen fest.
Es gilt nicht für Koordinatenmesssysteme, wie sie in der Normenreihe ISO 10360 festgelegt sind, unabhängig davon, ob die Systeme mit einer Drehachse ausgestattet sind oder nicht, es sei denn, es besteht eine besondere Vereinbarung.

Spécification géométrique des produits (GPS) - Équipements de mesure de forme ; Instruments de mesure de forme à plateau tournant - Caractéristiques de conception et caractéristiques métrologiques (ISO 5463:2024)

Le présent document spécifie les caractéristiques de conception et les caractéristiques métrologiques les plus importantes des instruments de mesure de forme à plateau tournant.
Il ne s’applique pas aux systèmes de mesure de coordonnées tels que définis par la série ISO 10360, que les systèmes soient dotés d’un axe de rotation ou non, sauf en cas d’accord spécial.

Specifikacija geometrijskih veličin izdelka - Oprema za merjenje oblike; naprave za merjenje oblike z rotacijsko osjo - Zasnova in meroslovne značilnosti (ISO 5463:2024)

General Information

• Status: Not Published
• Public Enquiry End Date: 22-Oct-2023
• ICS: 17.040.30 - Measuring instruments
• ICS: 17.040.40 - Geometrical Product Specification (GPS)
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 08-Oct-2024
• Due Date: 13-Dec-2024
• Ref Project: EN ISO 5463:2024 - Geometrical product specifications (GPS) - Rotary axis form-measuring instruments - Design and metrological characteristics (ISO 5463:2024)

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 5463:2023
01-oktober-2023
Specifikacija geometrijskih veličin izdelka - Oprema za merjenje oblike; naprave za
merjenje oblike z rotacijsko osjo - Zasnova in meroslovne značilnosti (ISO/DIS
5463:2023)
Geometrical product specifications (GPS) - Form measuring equipment; Rotary axis form
measuring instruments - Design and metrological characteristics (ISO/DIS 5463:2023)
Geometrische Produktspezifikationen (GPS) - Formmessgeräte; Formmessgeräte mit
Drehachse - Konstruktion und messtechnische Eigenschaften (ISO/DIS 5463:2023)
Spécification géométrique des produits (GPS) - Équipements de mesure de forme ;
Instruments de mesure de forme à plateau tournant - Caractéristiques de conception et
caractéristiques métrologiques (ISO/DIS 5463:2023)
Ta slovenski standard je istoveten z: prEN ISO 5463
ICS:
17.040.30 Merila Measuring instruments
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
oSIST prEN ISO 5463:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

oSIST prEN ISO 5463:2023
oSIST prEN ISO 5463:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 5463
ISO/TC 213 Secretariat: BSI
Voting begins on: Voting terminates on:
2023-08-01 2023-10-24
Geometrical product specifications (GPS) — Form
measuring equipment; Rotary axis form measuring
instruments — Design and metrological characteristics
Spécification géométrique des produits (GPS) — Équipements de mesure de forme ; Instruments de mesure
de forme à plateau tournant — Caractéristiques de conception et caractéristiques métrologiques
ICS: 17.040.30; 17.040.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 5463:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

oSIST prEN ISO 5463:2023
ISO/DIS 5463:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 5463
ISO/TC 213 Secretariat: BSI
Voting begins on: Voting terminates on:

Geometrical product specifications (GPS) — Form
measuring equipment; Rotary axis form measuring
instruments — Design and metrological characteristics
Spécification géométrique des produits (GPS) — Équipements de mesure de forme ; Instruments de mesure
de forme à plateau tournant — Caractéristiques de conception et caractéristiques métrologiques
ICS: 17.040.30; 17.040.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 5463:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

oSIST prEN ISO 5463:2023
ISO/DIS 5463:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 General terms . 2
3.2 Terms relating to probe system . 4
4 Design characteristics . 4
4.1 General . 4
4.2 Types of rotary axis form measuring instrument . 5
4.2.1 General . 5
4.2.2 Rotating workpiece instrument . 5
4.2.3 Stationary workpiece instrument. 6
4.3 Design characteristics of probe . 9
4.3.1 Contact probe . 9
5 Metrological characteristics .10
5.1 General . 10
5.2 Environmental requirements. 10
5.2.1 General . 10
5.2.2 Environmental conditions . 10
5.2.3 Operating conditions . 11
5.3 Error separation technique . 11
5.4 Probe characteristic . 11
5.4.1 Reference point . 11
5.4.2 Probe error . 11
6 Determination of conformity to specification .14
6.1 General . 14
6.2 Measurement uncertainty . . 14
6.3 Decision rule . 14
Annex A (normative) Design and metrological characteristics for rotating workpiece
instruments .15
Annex B (informative) Artefacts for metrological characteristics .34
Annex C (informative) Dynamic response of the probe .39
Annex D (informative) Example of a test protocol.42
Annex E (informative) Incidental machine characteristics .43
Annex F (informative) Other type of probes . 44
Annex G (informative) Relation to the GPS matrix model .46
Bibliography .47
iii
oSIST prEN ISO 5463:2023
ISO/DIS 5463:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 213.
iv
oSIST prEN ISO 5463:2023
ISO/DIS 5463:2023(E)
Introduction
This is a Geometrical Product Specification standard and is to be regarded as a General GPS standard
(see ISO 14638). It influences the chain link F of the chains of standards on form, orientation, location
and run-out. For more detailed information of the relation of this standard to other standards and the
GPS matrix model, see Annex E.
The ISO/GPS matrix model given in ISO 14638 gives an overview of the ISO/GPS system of which this
document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and
the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this
document, unless otherwise indicated; see ISO/TR 14253-6 for additional information on the selection
of
...