SIST EN ISO 23145-2:2016
(Main)Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of bulk density of ceramic powders - Part 2: Untapped density (ISO 23145-2:2012)
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of bulk density of ceramic powders - Part 2: Untapped density (ISO 23145-2:2012)
This part of ISO 23145 specifies the test method to determine the untapped density of granulated or ungranulated ceramic powders by a constant-volume measuring method.
Hochleistungskeramik - Bestimmung der Dichte von keramischen Pulvern - Teil 2: Schüttdichte (ISO 23145-2:2012)
Dieser Teil von ISO 23145 legt ein Verfahren zur Bestimmung der Schüttdichte von granulierten oder nicht granulierten keramischen Pulvern mit einer Volumenkonstanzmethode fest.
Céramiques techniques - Détermination de la masse volumique des poudres céramiques - Partie 2: Masse volumique sans tassement (ISO 23145-2:2012)
L'ISO 23145-2:2012 spécifie la méthode d'essai permettant de déterminer la masse volumique sans tassement des poudres céramiques granulées ou non-granulées à l'aide d'une méthode de mesurage à volume constant.
Fina keramika (sodobna keramika, sodobna tehnična keramika) - Ugotavljanje prostorninske gostote keramičnih praškov - 2. del: Gostota brez potresanja (ISO 23145-2:2012)
Ta del standarda ISO 23145 določa metodo preskušanja za določanje gostote po stiskanju za granulirane ali negranulirane keramične praške z metodo merjenja konstantne prostornine.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 23145-2:2016
01-junij-2016
1DGRPHãþD
SIST EN 725-9:2006
)LQDNHUDPLND VRGREQDNHUDPLNDVRGREQDWHKQLþQDNHUDPLND 8JRWDYOMDQMH
SURVWRUQLQVNHJRVWRWHNHUDPLþQLKSUDãNRYGHO *RVWRWDEUH]SRWUHVDQMD ,62
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of
bulk density of ceramic powders - Part 2: Untapped density (ISO 23145-2:2012)
Hochleistungskeramik - Bestimmung der Dichte von keramischen Pulvern - Teil 2:
Schüttdichte (ISO 23145-2:2012)
Céramiques techniques - Détermination de la masse volumique des poudres céramiques
- Partie 2: Masse volumique sans tassement (ISO 23145-2:2012)
Ta slovenski standard je istoveten z: EN ISO 23145-2:2016
ICS:
81.060.30 Sodobna keramika Advanced ceramics
SIST EN ISO 23145-2:2016 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 23145-2:2016
---------------------- Page: 2 ----------------------
SIST EN ISO 23145-2:2016
EN ISO 23145-2
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2016
EUROPÄISCHE NORM
ICS 81.060.30 Supersedes EN 725-9:2006
English Version
Fine ceramics (advanced ceramics, advanced technical
ceramics) - Determination of bulk density of ceramic
powders - Part 2: Untapped density (ISO 23145-2:2012)
Céramiques techniques - Détermination de la masse Hochleistungskeramik - Bestimmung der Dichte von
volumique des poudres céramiques - Partie 2: Masse keramischen Pulvern - Teil 2: Schüttdichte (ISO 23145-
volumique sans tassement (ISO 23145-2:2012) 2:2012)
This European Standard was approved by CEN on 25 March 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23145-2:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 23145-2:2016
EN ISO 23145-2:2016 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 23145-2:2016
EN ISO 23145-2:2016 (E)
European foreword
The text of ISO 23145-2:2012 has been prepared by Technical Committee ISO/TC 206 “Fine ceramics”
of the International Organization for Standardization (ISO) and has been taken over as EN ISO 23145-
2:2016 by Technical Committee CEN/TC 184 “Advanced technical ceramics” the secretariat of which is
held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2016, and conflicting national standards shall
be withdrawn at the latest by October 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN 725-9:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 23145-2:2012 has been approved by CEN as EN ISO 23145-2:2016 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 23145-2:2016
---------------------- Page: 6 ----------------------
SIST EN ISO 23145-2:2016
INTERNATIONAL ISO
STANDARD 23145-2
First edition
2012-06-01
Fine ceramics (advanced ceramics,
advanced technical ceramics) —
Determination of bulk density of
ceramic powders —
Part 2:
Untapped density
Céramiques techniques — Détermination de la masse volumique des
poudres céramiques —
Partie 2: Masse volumique sans tassement
Reference number
ISO 23145-2:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
SIST EN ISO 23145-2:2016
ISO 23145-2:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 23145-2:2016
ISO 23145-2:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
5 Sampling . 4
6 Procedure . 5
7 Calculation . 5
8 Test report . 5
Bibliography . 7
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 23145-2:2016
ISO 23145-2:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
...
SLOVENSKI STANDARD
kSIST FprEN ISO 23145-2:2015
01-november-2015
)LQDNHUDPLND VRGREQDNHUDPLNDVRGREQDWHKQLþQDNHUDPLND 8JRWDYOMDQMH
SURVWRUQLQVNHJRVWRWHNHUDPLþQLKSUDãNRYGHO *RVWRWDEUH]SRWUHVDQMD ,62
Fine ceramics (advanced ceramics, advanced technical ceramics) - Determination of
bulk density of ceramic powders - Part 2: Untapped density (ISO 23145-2:2012)
Hochleistungskeramik - Bestimmung der Dichte von keramischen Pulvern - Teil 2:
Schüttdichte (ISO 23145-2:2012)
Céramiques techniques - Détermination de la masse volumique des poudres céramiques
- Partie 2: Masse volumique sans tassement (ISO 23145-2:2012)
Ta slovenski standard je istoveten z: FprEN ISO 23145-2
ICS:
81.060.30 Sodobna keramika Advanced ceramics
kSIST FprEN ISO 23145-2:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST FprEN ISO 23145-2:2015
---------------------- Page: 2 ----------------------
kSIST FprEN ISO 23145-2:2015
FINAL DRAFT
EUROPEAN STANDARD
FprEN ISO 23145-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2015
ICS 81.060.30 Will supersede EN 725-9:2006
English Version
Fine ceramics (advanced ceramics, advanced technical
ceramics) - Determination of bulk density of ceramic
powders - Part 2: Untapped density (ISO 23145-2:2012)
Céramiques techniques - Détermination de la masse Hochleistungskeramik - Bestimmung der Dichte von
volumique des poudres céramiques - Partie 2: Masse keramischen Pulvern - Teil 2: Schüttdichte (ISO 23145-
volumique sans tassement (ISO 23145-2:2012) 2:2012)
This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the
Technical Committee CEN/TC 184.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprEN ISO 23145-2:2015 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST FprEN ISO 23145-2:2015
FprEN ISO 23145-2:2015 (E)
Contents
Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
kSIST FprEN ISO 23145-2:2015
FprEN ISO 23145-2:2015 (E)
European foreword
The text of ISO 23145-2:2012 has been prepared by Technical Committee ISO/TC 206 “Fine ceramics”
of the International Organization for Standardization (ISO) and has been taken over as
FprEN ISO 23145-2:2015 by Technical Committee CEN/TC 184 “Advanced technical ceramics” the
secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
This document will supersede EN 725-9:2006.
Endorsement notice
The text of ISO 23145-2:2012 has been approved by CEN as FprEN ISO 23145-2:2015 without any
modification.
3
---------------------- Page: 5 ----------------------
kSIST FprEN ISO 23145-2:2015
---------------------- Page: 6 ----------------------
kSIST FprEN ISO 23145-2:2015
INTERNATIONAL ISO
STANDARD 23145-2
First edition
2012-06-01
Fine ceramics (advanced ceramics,
advanced technical ceramics) —
Determination of bulk density of
ceramic powders —
Part 2:
Untapped density
Céramiques techniques — Détermination de la masse volumique des
poudres céramiques —
Partie 2: Masse volumique sans tassement
Reference number
ISO 23145-2:2012(E)
©
ISO 2012
---------------------- Page: 7 ----------------------
kSIST FprEN ISO 23145-2:2015
ISO 23145-2:2012(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2012
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
kSIST FprEN ISO 23145-2:2015
ISO 23145-2:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
5 Sampling . 4
6 Procedure . 5
7 Calculation . 5
8 Test report . 5
Bibliography . 7
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
kSIST FprEN ISO 23145-2:2015
ISO 23145-2:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.