SIST-TP CEN/TR 15339-5:2015

Thermal spraying - Safety requirements for thermal spraying equipment - Part 5: Powder and wire feed units

This part of EN 15339 specifies safety requirements of machines and equipment for thermal spraying, in this case of gas supply including supply of liquid fuels.
This part of EN 15339 should be used in conjunction with prEN 15339-1, which deals with general aspects when designing, manufacturing, and/or putting in service of machines or equipment and with the responsibility for issuing the CE Conformity Declaration.
Generally, the requirements of EU Directive 94/9/EC [1] are valid for the use of this European Standard.

Thermisches Spritzen - Sicherheitsanforderungen für Einrichtungen für das thermische Spritzen - Teil 5: Pulver- und Drahtfördereinheiten

Dieser Teil der EN 15339 legt Sicherheitsanforderungen von Maschinen und Einrichtungen zum thermischen Spritzen fest, in diesem Fall von Pulver- und Drahtfördereinheiten.
Dieser Teil der EN 15339 sollte in Verbindung mit der Norm prEN 15339-1 angewandt werden, die die allgemeinen Aspekte der Konstruktion, Herstellung, Inbetriebsetzung und/oder des Betriebes von Maschinen oder Einrichtungen und die Verantwortung für Ausstellung der CE Konformitätserklärung behandelt.
Grundsätzlich sind die Anforderungen der EU Richtlinie 94/9/EG [1] gültig für die Anwendung dieser Europäischen Norm.

Projection thermique - Exigences de sécurité relatives au matériel de projection thermique - Partie 5: Dispositifs d’alimentation en poudre et en fil

La présente Norme européenne spécifie les exigences de sécurité des machines et du matériel de projection thermique et, dans le cas présent, des dispositifs d’alimentation en poudre et en fil.
Il convient d’utiliser la présente norme conjointement avec le prEN 15339-1, qui traite des aspects généraux de conception, fabrication et/ou mise en service des machines ou du matériel et de la responsabilité de l’émission de la Déclaration CE de conformité.
D’une manière générale, les exigences de la Directive UE 94/9/CE [1] sont valables pour l’application de la présente Norme européenne.

Vroče brizganje - Varnostne zahteve za opremo za vroče brizganje - 5. del: Prah in žice dovodne enote

Ta del standarda EN 15339 določa varnostne zahteve za stroje in opremo za vroče brizganje, v tem primeru za oskrbo s plinom, vključno z oskrbo s tekočimi gorivi.
Ta del standarda EN 15339 naj bi se uporabljal v povezavi s standardom prEN 15339-1, v katerem so obravnavani splošni vidiki za projektiranje, proizvodnjo in/ali začetek uporabe strojev ali opreme ter odgovornost za izdajo izjave o skladnosti CE.
Na splošno zahteve iz Direktive 94/9/ES [1] veljajo za uporabo tega evropskega standarda.

General Information

• Status: Published
• Publication Date: 16-Feb-2015
• ICS: 25.220.20 - Surface treatment
• Technical Committee: IPKZ - Protection of metals against corrosion
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 27-Jan-2015
• Due Date: 03-Apr-2015
• Completion Date: 17-Feb-2015
• Ref Project: CEN/TR 15339-5:2014 - Thermal spraying - Safety requirements for thermal spraying equipment - Part 5: Powder and wire feed units

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TP CEN/TR 15339-5:2015
01-marec-2015
9URþHEUL]JDQMH9DUQRVWQH]DKWHYH]DRSUHPR]DYURþHEUL]JDQMHGHO3UDKLQ
åLFHGRYRGQHHQRWH
Thermal spraying - Safety requirements for thermal spraying equipment - Part 5: Powder
and wire feed units
Thermisches Spritzen - Sicherheitsanforderungen für Einrichtungen für das thermische
Spritzen - Teil 5: Pulver- und Drahtfördereinheiten
Projection thermique - Exigences de sécurité relatives au matériel de projection
thermique - Partie 5: Dispositifs d’alimentation en poudre et en fil
Ta slovenski standard je istoveten z: CEN/TR 15339-5:2014
ICS:
25.220.20 Površinska obdelava Surface treatment
SIST-TP CEN/TR 15339-5:2015 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TP CEN/TR 15339-5:2015

---------------------- Page: 2 ----------------------

SIST-TP CEN/TR 15339-5:2015

TECHNICAL REPORT
CEN/TR 15339-5

RAPPORT TECHNIQUE

TECHNISCHER BERICHT
December 2014
ICS 25.220.20
English Version
Thermal spraying - Safety requirements for thermal spraying
equipment - Part 5: Powder and wire feed units
Projection thermique - Exigences de sécurité relatives au Thermisches Spritzen - Sicherheitsanforderungen für
matériel de projection thermique - Partie 5: Dispositifs Einrichtungen für das thermische Spritzen - Teil 5: Pulver-
d'alimentation en poudre et en fil und Drahtfördereinheiten


This Technical Report was approved by CEN on 16 September 2014. It has been drawn up by the Technical Committee CEN/TC 240.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TR 15339-5:2014 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TP CEN/TR 15339-5:2015
CEN/TR 15339-5:2014 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Function of the powder and wire feed units .4
3.1 General .4
3.2 Features of the powder feed unit .4
3.3 Features of the wire feed unit .5
3.3.1 Flame spraying .5
3.3.2 Arc spraying .5
4 Potential hazards .5
4.1 General .5
4.2 Powder feed units .5
4.3 Wire feed units .5
5 Safety requirements — Protection measures .6
5.1 General .6
5.2 Safety requirements and protection measures for powder feed units in the case of flame,
HVOF, and plasma spraying .6
5.3 Safety requirements for wire feed units and protection measures in the case of arc
spraying .6
6 Requirements for manufacture, supply, service and maintenance.6
6.1 Requirements of the manufacturer .6
6.2 Requirements of the integrator .7
6.3 Requirements of the user .7
7 National rules .7
Bibliography .8

2

---------------------- Page: 4 ----------------------

SIST-TP CEN/TR 15339-5:2015
CEN/TR 15339-5:2014 (E)
Foreword
This document (CEN/TR 15339-5:2014) has been prepared by Technical Committee CEN/TC 240 “Thermal
spraying and thermally sprayed coatings”, the secretariat of which is held by DIN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
CEN/TR 15339, Thermal spraying - Safety requirements for thermal spraying equipment is composed of the
following parts:
— Part 1: General requirements
— Part 2: Gas control units (published as a European Standard)
— Part 3: Torches for thermal spraying and their connection and supply units
— Part 4: Gas and liquid fuel supply
— Part 5: Powder and wire feed units
— Part 6: Spray booth, Handling system, Dust collection, Exhaust system, Filter
3

---------------------- Page: 5 ----------------------

SIST-TP CEN/TR 15339-5:2015
CEN/TR 15339-5:2014 (E)
1 Scope
This Technical Report specifies safety requirements of equipment for thermal spraying, in this case of powder
and wire feed units.
This part of CEN/TR 15339 should be used in conjunction with CEN/TR 15339-1, which deals with general
aspects of designing, manufacturing, and/or putting in service of machines or equipment and with the
responsibility for issuing the CE Conformity Declaration.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its appli
...