SIST EN ISO 21420:2020/A1:2024
(Amendment)Protective gloves - General requirements and test methods - Amendment 1 (ISO 21420:2020/Amd 1:2022)
Protective gloves - General requirements and test methods - Amendment 1 (ISO 21420:2020/Amd 1:2022)
Schutzhandschuhe - Allgemeine Anforderungen und Prüfverfahren - Änderung 1 (ISO 21420:2020/Amd 1:2022)
Gants de protection - Exigences générales et méthodes d’essai - Amendement 1 (ISO 21420:2020/Amd 1:2022)
Varovalne rokavice - Splošne zahteve in preskusne metode - Dopolnilo A1 (ISO 21420:2020/Amd 1:2022)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2024
Varovalne rokavice - Splošne zahteve in preskusne metode - Dopolnilo A1 (ISO
21420:2020/Amd 1:2022)
Protective gloves - General requirements and test methods - Amendment 1 (ISO
21420:2020/Amd 1:2022)
Schutzhandschuhe - Allgemeine Anforderungen und Prüfverfahren - Änderung 1 (ISO
21420:2020/Amd 1:2022)
Gants de protection - Exigences générales et méthodes d’essai - Amendement 1 (ISO
21420:2020/Amd 1:2022)
Ta slovenski standard je istoveten z: EN ISO 21420:2020/A1:2024
ICS:
13.340.40 Varovanje dlani in rok Hand and arm protection
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 21420:2020/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2024
EUROPÄISCHE NORM
ICS 13.340.40
English Version
Protective gloves - General requirements and test methods
- Amendment 1 (ISO 21420:2020/Amd 1:2022)
Gants de protection - Exigences générales et méthodes Schutzhandschuhe - Allgemeine Anforderungen und
d'essai - Amendement 1 (ISO 21420:2020/Amd Prüfverfahren - Änderung 1 (ISO 21420:2020/Amd
1:2022) 1:2022)
This amendment A1 modifies the European Standard EN ISO 21420:2020; it was approved by CEN on 29 May 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21420:2020/A1:2024 E
worldwide for CEN national Members.
Contents Page
European foreword. 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Regulation 2016/425 aimed to be covered . 4
European foreword
This document (EN ISO 21420:2020/A1:2024) has been prepared by Technical Committee ISO/TC
94 "Personal safety -- Personal protective equipment" in collaboration with Technical Committee
CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets” the secretariat
of which is held by DIN.
This Amendment to the European Standard EN ISO 21420:2020 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by January 2025,
and conflicting national standards shall be withdrawn at the latest by January 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a standardization request addressed to CEN by the
European Commission. The Standing Committee of the EFTA States subsequently approves these
requests for its Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
Endorsement notice
The text of ISO 21420:2020/Amd 1:2022 has been approved by CEN as EN ISO 21420:2020/A1:2024
without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of Regulation 2016/425 aimed to be covered
This European Standard has been prepared under a Commission’s standardization request to
provide one voluntary means of conforming to essential requirements of Regulation (EU)
2016/425 EEC on the approximation of the laws of the Member States relating to personal
protective equipment.
Once this standard is cited in the Official Journal of the European Union under that Regulation,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the
limits of the scope of this standard, a presumption of conformity with the corresponding Essential
Requirements of that Regulation and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex II of Regulation
2016/425
Essential Health and Safety Requirements of Clause(s)/sub-clause(s)
Remarks/Notes
Regulation 2016/425, Annex II of this EN
1.2.1.1 Innocuousness of PPE- suitable 4.2
constituent materials
1.2.1.3 Maximum permissible user impediment 5.2
1.4 Information supplied by the manufacturer 7.3
2.4 PPE subject to ageing 4.3
7.2.1.1 f) & 7.2.2 g)
2.5 PPE which may be caught up during use 7.3.7
2.6 PPE for use in potentially explosive 4.4
atmosphere
2.12 PPE bearing one or more identification or 7.2.1.1 d) —
recognition marks directly or indirectly relating 7.2.2 e) —
to health and safety 7.3.5
INTERNATIONAL ISO
STANDARD 21420
First edition
2020-02
AMENDMENT 1
2022-07
Protective gloves — General
requirements and test methods
AMENDMENT 1
Gants de protection — Exigences générales et méthodes d’essai
AMENDEMENT 1
Reference number
ISO 21420:2020/Amd.1:2022(E)
ISO 21420:2020/Amd.1:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 21420:2020/Amd.1:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/
iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety -- Personal protective
equipment, Subcommittee SC 13, Protective Clothing.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iii
ISO 21420:2020/Amd.1:2022(E)
Protective gloves — General requirements and test
methods
AMENDMENT 1
Normative references
Replace text of Clause 2 by changing the undated normative references to dated normative references
as follows:
“The following documents are referred to in the text in such a way that
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.