SIST ETS 300 705-2:2000
(Main)Digital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for end system configuration; Profile Implementation Conformance Statement (ICS); Part 2: Fixed radio Termination (FT)
Digital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for end system configuration; Profile Implementation Conformance Statement (ICS); Part 2: Fixed radio Termination (FT)
Profile Implementation Conformace Statement (ICS) proforma for the DECT/ISDN interworking profile specific protocol requirements of ETS 300 434 (DE/RES-03-14) & DE/RES-03039 in copliance with the relevant requirements, and in accordance with the relevant guidance, given in ISO/IEC 9646-6 & 7 and in ETS 300 406.
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Digitalno omrežje z integriranimi storitvami (ISDN) - Vzajemno delovanje DECT/ISDN v obliki končnega sistema - Profil izjave o skladnosti izvedbe (ICS) - 2. del: Fiksna radijska zaključitev (FT)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Digital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital Network (ISDN); DECT/ISDN interworking for end system configuration; Profile Implementation Conformance Statement (ICS); Part 2: Fixed radio Termination (FT)33.080Digitalno omrežje z integriranimi storitvami (ISDN)Integrated Services Digital Network (ISDN)33.070.30'(&7Digital Enhanced Cordless Telecommunications (DECT)ICS:Ta slovenski standard je istoveten z:ETS 300 705-2 E13SIST ETS 300 705-2:en01-QRYHPEHU-3SIST ETS 300 705-2:SLOVENSKI
STANDARD
EUROPEANETS 300 705-2TELECOMMUNICATIONJune 1997STANDARDSource: ETSI EP-DECTReference: DE/DECT-040045-2ICS:33.020Key words:DECT, ISDN, ICS, radio, testingDigital Enhanced Cordless Telecommunications (DECT);Integrated Services Digital Network (ISDN);DECT/ISDN interworking for end system configuration;Profile Implementation Conformance Statement (ICS);Part 2: Fixed radio Termination (FT)ETSIEuropean Telecommunications Standards InstituteETSI SecretariatPostal address: F-06921 Sophia Antipolis CEDEX - FRANCEOffice address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCEX.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat@etsi.frTel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and theforegoing restriction extend to reproduction in all media.© European Telecommunications Standards Institute 1997. All rights reserved.SIST ETS 300 705-2:2000
Page 2ETS 300 705-2: June 1997Whilst every care has been taken in the preparation and publication of this document, errors in content,typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to"ETSI Editing and Committee Support Dept." at the address shown on the title page.SIST ETS 300 705-2:2000
Page 3ETS 300 705-2: June 1997ContentsForeword.71Scope.92Normative references.93Definitions and abbreviations.113.1Definitions.113.2Abbreviations.114Conformance requirement concerning Profile ICS.11Annex A (normative):System Conformance Statement (SCS) proforma for DECT FT IAP.14A.1Identification.14A.1.1Description of the system.14A.1.2Supplier of the system.14A.1.3Client identification.15A.1.4Contact person identification.15A.1.5Signature of the client or of the supplier.15A.2Protocol identification.16A.3Profile identification.16A.4Combination description table.16A.5Configurability table.16A.6Additional information.17Annex B (normative):Requirement lists for DECT FT IAP.18B.1General.18B.1.1Profile Requirement List (Profile RL).18B.1.2General conditions.19B.2Requirement lists on DECT protocols.19B.2.1Requirement list on DECT NWK layer.19B.2.1.1Network entities.19B.2.1.2Network features.19B.2.1.2.1CC features.19B.2.1.2.2SS features (services).20B.2.1.2.3LCE features.22B.2.1.3Procedures.22B.2.1.4Messages.24B.2.1.4.1CC messages.24B.2.1.4.2CRSS and CISS messages.25B.2.1.4.3LCE messages.25B.2.2Requirement list on DECT DLC layer.26B.2.2.1Services.26B.2.2.1.1C-plane services.26B.2.2.1.2U-plane services.26B.2.2.2Procedures.26SIST ETS 300 705-2:2000
Page 4ETS 300 705-2: June 1997B.2.2.2.1Generic signalling procedures.26B.2.2.2.2Class A procedures.27B.2.2.2.3Broadcast procedures.27B.2.2.2.4LU1 procedures.27B.2.2.3Parameters.27B.2.2.3.1LU1 parameters.27B.2.2.4Messages.28B.2.2.4.1C-plane PDUs.28B.2.3Requirement list on DECT MAC layer.28B.2.3.1Services.28B.2.3.1.1Connection oriented control services.28B.2.3.1.2Broadcast control services.29B.2.3.1.3Multiplexing services.29B.2.3.2Procedures.31B.2.3.2.1Connection setup procedures.31B.2.3.2.2Connection data transfer procedures.31B.2.3.2.3Connection release procedures.31B.2.3.2.4Broadcast procedures.31B.2.3.2.5CSF multiplexing procedures.32B.2.3.2.6Layer management procedures.32B.2.3.3Other capabilities.32B.2.3.4Messages.33B.2.3.4.1A-field header - B-field identification.33B.2.3.4.2Paging tail messages supported.33B.2.3.4.3MAC control messages supported.34B.2.3.4.4B-field messages supported.34B.2.3.5MAC messages format and field value.36B.2.3.5.1QT - Fixed part capability.36B.2.4Requirement list on DECT PHL layer.36B.2.5Requirement list on ISDN L3 layer tables.37B.2.5.1ISDN L3 layer primary access tables.37B.2.5.2ISDN L3 layer basic access tables.37B.2.6Requirement list on ISDN L2 layer tables.37B.2.6.1ISDN L2 layer primary access tables.37B.2.6.2ISDN L2 layer basic access tables.37B.2.7Requirement list on ISDN L1 layer tables.37B.2.7.1ISDN L1 layer primary access tables.37B.2.7.2ISDN L1 layer basic access tables.37Annex C (normative):Profile specific ICS proforma for DECT FT IAP.38C.1Guidance for completing the profile specific proforma.38C.1.1Purposes and structure.38C.1.2Instructions for completing the Profile specific ICS.40C.2Identification of the implementation.40C.2.1Date of statement.40C.2.2Identification of the implementation.40C.2.3Contact person identification.40C.2.4Relationship with the System Conformance Statement (SCS).41C.3Identification of the profile.41C.3.1Defect report numbers and amendments implemented.41C.3.2Addenda implemented.42C.4Profile ICS proforma tables.42C.4.1Global statement of conformance.42C.4.2Profile ICS features tables.42C.4.3Profile ICS IWU tables.43C.4.3.1IWU procedures.43SIST ETS 300 705-2:2000
Page 5ETS 300 705-2: June 1997C.4.3.2IWU messages mapping.45C.4.4Profile ICS NWK layer tables.53C.4.5Profile ICS DLC layer tables.53C.4.6Profile ICS MAC layer tables.53Annex D (normative):Messages redefinition for DECT CI FT PICS proforma.54D.1Description.54D.2CC messages.54D.3Connection Related Supplementary Service (CRSS) and Connection Independent SupplementaryService (CISS) messages.62D.4Information elements.66D.5Timers and constants support.69History.70SIST ETS 300 705-2:2000
Page 6ETS 300 705-2: June 1997Blank pageSIST ETS 300 705-2:2000
Page 7ETS 300 705-2: June 1997ForewordThis European Telecommunication Standard (ETS) has been produced by the Digital Enhanced CordlessTelecommunications (DECT) Project of the European Telecommunications Standards Institute (ETSI).This ETS comprises two parts:Part 1:"Portable radio Termination (PT)".Part 2:"Fixed radio Termination (FT)".Annex A of this ETS contains the System Conformance Statement (SCS) proforma for the DECT FT ISDNAccess Profile (IAP).Annex B of this ETS contains the requirement lists for the DECT FT IAP.Annex C of this ETS contains the specific ICS proforma for the DECT FT IAP.Transposition datesDate of adoption:6 June 1997Date of latest announcement of this ETS (doa):30 September 1997Date of latest publication of new National Standardor endorsement of this ETS (dop/e):31 March 1998Date of withdrawal of any conflicting National Standard (dow):31 March 1998SIST ETS 300 705-2:2000
Page 8ETS 300 705-2: June 1997Blank pageSIST ETS 300 705-2:2000
Page 9ETS 300 705-2: June 19971ScopeThis European Telecommunication Standard (ETS) provides the Profile Implementation ConformanceStatement (Profile ICS) proforma for the Digital Enhanced Cordless Telecommunications DECT/ISDN inter-working for end system configuration Profile at the Fixed Termination as defined in ETS 300 434-1 [10],and ETS 300 434-2 [11] in compliance with the relevant requirements and in accordance with the relevantguidance given in ISO/IEC 9646-7 [18].The supplier of an implementation which is claimed to conform to ETS 300 434-1 [10] andETS 300 434-2 [11] is required to complete a copy of the PICS proforma ETS 300 476 parts 4, 5, 6 and7 [12], [13], [14] and [15], with the replacements provided by the requirement lists given in annex B of thisETS, as well as a copy of the specific ICS proforma provided in the annex C of this ETS.2Normative referencesThis ETS incorporates, by dated or undated reference, provisions from other publications. These normativereferences are cited at the appropriate places in the text and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this ETSonly when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies.[1]ETS 300 175-1: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 1: Overview".[2]ETS 300 175-2: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 2: Physical layer (PHL)".[3]ETS 300 175-3: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 3: Medium Access Control (MAC) layer".[4]ETS 300 175-4: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 4: Data Link Control (DLC) layer".[5]ETS 300 175-5: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 5: Network (NWK) layer".[6]ETS 300 175-6: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 6: Identities and addressing".[7]ETS 300 175-7: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 7: Security features".[8]ETS 300 175-8: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 8: Speech coding and transmission".[9]ETS 300 175-9: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Part 9: Public Access Profile (PAP)".[10]ETS 300 434-1: "Digital Enhanced Cordless Telecommunications (DECT) andIntegrated Services Digital Network (ISDN) interworking for end systemconfiguration; Part 1: Interworking specification".[11]ETS 300 434-2: "Digital Enhanced Cordless Telecommunications (DECT) andIntegrated Services Digital Network (ISDN) interworking for end systemconfiguration; Part 2: Access profile".[12]ETS 300 476-4: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Protocol Implementation Conformance Statement(PICS) proforma; Part 4: Network (NWK) layer - Fixed radio Termination (FT)".SIST ETS 300 705-2:2000
Page 10ETS 300 705-2: June 1997[13]ETS 300 476-5: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Protocol Implementation Conformance Statement(PICS) proforma; Part 5: Data Link Control (DLC) layer - Fixed radio Termination(FT)".[14]ETS 300 476-6: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Protocol Implementation Conformance Statement(PICS) proforma; Part 6: Medium Access Control (MAC) layer - Fixed radioTermination (FT)".[15]ETS 300 476-7: "Digital Enhanced Cordless Telecommunications (DECT);Common Interface (CI); Protocol Implementation Conformance Statement(PICS) proforma; Part 7: Physical layer".[16]ISO/IEC 9646-1 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 1:General concepts". (See also CCITT Recommendation X.290 (1991)).[17]ISO/IEC 9646-6 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 6:Protocol profile test specification".[18]ISO/IEC 9646-7 (1991): "Information technology - Open SystemsInterconnection - Conformance testing methodology and framework - Part 7:Implementation conformance statement".[19]ETS 300 406: "Methods for Testing and Specification (MTS); Protocol andprofile conformance testing specifications; Standardization methodology".[20]ETS 300 403-1: "Integrated Services Digital Network (ISDN); Digital SubscriberSignalling System No. one (DSS1) protocol; Signalling network layer forcircuit-mode basic call control; Part 1: Protocol specification [ITU-TRecommendation Q.931 (1993), modified]".[21]ETS 300 403-3: "Integrated Services Digital Network (ISDN); Digital SubscriberSignalling System No. one (DSS1) protocol; Signalling network layer forcircuit-mode basic call control; Part 3: Protocol Implementation ConformanceStatement (PICS) proforma specification".[22]ETS 300 402-2: "Integrated Services Digital Network (ISDN); Digital SubscriberSignalling System No. one (DSS1) protocol; Data link layer; Part 2: Generalprotocol specification [ITU-T Recommendation Q.921 (1993), modified]".[23]ETS 300 402-4: "Integrated Services Digital Network (ISDN); Digital SubscriberSignalling System No. one (DSS1) protocol; Data link layer; Part 4: ProtocolImplementation Conformance Statement (PICS) proforma specification for thegeneral protocol".[24]ETS 300 011 (1992): "Integrated Services Digital Network (ISDN); Primary rateuser-network interface; Layer 1 specification and test principles".[25]ETS 300 011/A2: "Amendment 2 to ETS 300 011 (1992), adding a SCS, a PICSand a PIXIT for interface points Ia and Ib".[26]ETS 300 012 (1992): "Integrated Services Digital Network (ISDN); Basic user-network interface; Layer 1 specification and test principles".[27]ETS 300 012/A2: "Amendment 2 to ETS 300 012 (1992), adding a SCS, a PICSand a PIXIT for interface points Ia and Ib".SIST ETS 300 705-2:2000
Page 11ETS 300 705-2: June 1997[28]ETS 300 196-1: "Integrated Services Digital Network (ISDN); Generic functionalprotocol for the support of supplementary services; Digital Subscriber SignallingSystem No. one (DSS1) protocol; Part 1: Protocol specification".[29]ETS 300 196-2: "Integrated Services Digital Network (ISDN); Generic functionalprotocol for the support of supplementary services; Digital Subscriber SignallingSystem No. one (DSS1) protocol; Part 2: Protocol Implementation ConformanceStatement (PICS) proforma specification".3Definitions and abbreviations3.1DefinitionsFor the purposes of this ETS, the following terms and definitions apply:a)the terms defined in ISO/IEC 9646-7 [18];b)the definitions in ETS 300 434-1 [10] and ETS 300 434-2 [11]; andc)the following terms defined in ISO/IEC 9646-1 [16]:-PICS proforma;-Profile Implementation Conformance Statement (Profile ICS).3.2AbbreviationsFor the purposes of this ETS, the abbreviations defined in ISO/IEC 9646-1 [16], the abbreviations definedin ETS 300 434-1 [10] and ETS 300 434-2 [11] apply.4Conformance requirement concerning Profile ICSThe supplier of a protocol implementation which is claimed to conform to the Fixed Termination specificrequirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] shall:-verify that his protocol implementation meets the Profile Requirements Lists (Profile RLs) for eachDECT protocol layer, contained in annex B of this ETS;-complete a copy of the Profile specific ICS proforma provided in annex C;-complete a copy of the System Conformance Statement (SCS) proforma provided in annex A; and-provide the information necessary to identify both the supplier and the implementation.Tables 1 and 2 provide guidance to indicate how to fulfil the PICS proforma required for the profile.SIST ETS 300 705-2:2000
Page 12ETS 300 705-2: June 1997Table 1: DECT PICS proforma tablePICSTablesChangeETS 300 476-4 [12]A.12Status column updated by RL subclause B.2.1.1A.13 to A.16Status column updated by RL subclause B.2.1.2A.18 to A.20Status column updated by RL subclause B.2.1.3A.23 to A.24Status column updated by RL subclause B.2.1.3A.25 to A.26Status column updated by RL subclause B.2.1.4.1A.51 to A.55Status column updated by RL subclause B.2.1.4.2A.58Status column updated by RL subclause B.2.1.4.2A.61 to A.71Status column updated by RL subclause B.2.1.4.2A.73 to A.74Status column updated by RL subclause B.2.1.4.2A.76 to A.78Status column updated by RL subclause B.2.1.4.2A.82Status column updated by RL subclause B.2.1.4.2A.85Status column updated by RL subclause B.2.1.4.2A.86 to A.87Status column updated by RL subclause B.2.1.4.3A.126 to A.129Status column updated by RL subclause B.2.1.4.4A.27 to A.41Tables replaced by annex D subclause D.2A.88 to A.89Tables replaced by annex D subclause D.2A.95Tables replaced by annex D subclause D.2A.101 to A.105Tables replaced by annex D subclause D.2A.209Tables replaced by annex D subclause D.3A.258Tables replaced by annex D subclause D.3A.285Tables replaced by annex D subclause D.3A.314Tables replaced by annex D subclause D.4All other tablesUnchangedETS 300 476-5 [13]A.9 to A.12Status column updated by RL subclause B.2.2.1A.13 to A.14Status column updated by RL subclause B.2.2.2A.16 to A.17Status column updated by RL subclause B.2.2.2A.28 to A.29Status column updated by RL subclause B.2.2.2A.32Status column updated by RL subclause B.2.2.2A.38Status column updated by RL subclause B.2.2.3A.54Status column updated by RL subclause B.2.2.4All other tablesUnchangedETS 300 476-6 [14]A.9 to A.12Status column updated by RL subclause B.2.3.1A.14 to A.15Status column updated by RL subclause B.2.3.1A.19 to A.25Status column updated by RL subclause B.2.3.1A.26 to A.28Status column updated by RL subclause B.2.3.2A.30 to A.33Status column updated by RL subclause B.2.3.2A.36 to A.37Status column updated by RL subclause B.2.3.2A.38 to A.39Status column updated by RL subclause B.2.3.3A.50 to A.51Status column updated by RL subclause B.2.3.4A.57 to A.60Status column updated by RL subclause B.2.3.4A.69 to A.70Status column updated by RL subclause B.2.3.4A.88Status column updated by RL subclause B.2.3.5All other tablesUnchangedETS 300 476-7 [15]A.15Status column updated by RL subclause B.2.4All other tablesUnchangedSIST ETS 300 705-2:2000
Page 13ETS 300 705-2: June 1997Table 2: ISDN PICS proforma tablePICSTablesChangeETS 300 403-3 [21]All tablesUnchangedETS 300 402-4 [23]All tablesUnchangedETS 300 011/A2 [25]All tablesUnchangedETS 300 012/A2 [27]All tablesUnchangedETS 300 196-2 [29]All tablesUnchangedSIST ETS 300 705-2:2000
Page 14ETS 300 705-2: June 1997Annex A (normative):System Conformance Statement (SCS) proforma forDECT FT IAPNotwithstanding the provisions of the copyright clause related to the text of this ETS, ETSI grants thatusers of this ETS may freely reproduce the SCS proforma in this annex so that it can be used for itsintended purposes and may further publish the completed SCS.A.1IdentificationA.1.1Description of the systemTable A.1: Description of the systemProduct name:Hardware version number:Software version number:CPU Type:Bus-System:Operating System Name:Operating System version number:Additional:A.1.2Supplier of the systemTable A.2: Supplier of the systemCompany:Street:Postal Code / City:Country:SIST ETS 300 705-2:2000
Page 15ETS 300 705-2: June 1997A.1.3Client identificationIf different from the supplier.Table A.3: Client identificationCompany:Street:Postal Code / City:Country:A.1.4Contact person identificationTable A.4: Contact person identificationName:Telephone:Fax:Telex:E-Mail:A.1.5Signature of the client or of the supplierTable A.5: Signature of the client or of the supplierName:Position:Signature:Date:SIST ETS 300 705-2:2000
Page 16ETS 300 705-2: June 1997A.2Protocol identificationThis table identifies the protocols that have to be supported. The PCTR Reference column may be used torefer to any PCTR that have been obtained for these protocols in this system.Table A.6: Protocol identificationItemProtocol nameSpecificationReferencePICSReferencePCTRReferencePr1ISDN L3 layerETS 300 403-1 [20]ETS 300 403-3 [21]Pr2ISDN L2 layerETS 300 402-2 [22]ETS 300 402-4 [23]Pr3ISDN L1 layerETS 300 011 [24]ETS 300 012 [26]ETS 300 011/A2 [25]ETS 300 012/A2 [27]Pr4ISDN Generic FunctionalETS 300 196 [28]ETS 300 196-2 [29]Pr5DECT NWK layerETS 300 175-5 [5]ETS 300 476-4 [12]Pr6DECT DLC layerETS 300 175-4 [4]ETS 300 476-5 [13]Pr7DECT MAC layerETS 300 175-3 [3]ETS 300 476-6 [14]Pr8DECT PH layerETS 300 175-2 [2]ETS 300 476-7 [15]A.3Profile identificationThis table identifies the profiles that have to be supported. The SCTR Reference column may be used torefer to any SCTR that have been obtained for these profiles in this system.Table A.7: Profile identificationItemProfile identifierSpecificationReferenceProfile specific ICSReferenceSCTR ReferencePo1Generic Access Profile (GAP)ETS 300 444ETS 300 474Po2ISDN Access Profile (IAP)ETS 300 434ETS 300 705A.4Combination description tableThis clause identifies which combinations of protocols are allowed cause of supporting these profiles, andwhich combinations not covered by the profile are also supported.Table A.8: Combination tableItemProfileProtocolc1Po1Pr5, Pr6, Pr7, Pr8c2Po2Po1, Pr1, Pr2, Pr3, Pr4A.5Configurability tableThis clause identifies what kind of configuration or reconfiguration is needed in order to use each of theidentified combinations.Table A.9: Configurability tableCombinationAvailable always?Available by dynamicreconfiguration?Available by staticreconfiguration?c1c2SIST ETS 300 705-2:2000
Page 17ETS 300 705-2: June 1997A.6Additional informationAny additional information which is relevant for the product may be given here (e.g. information that isneeded for further certification: quality system used, available certificates, etc.).SIST ETS 300 705-2:2000
Page 18ETS 300 705-2: June 1997Annex B (normative):Requirement lists for DECT FT IAPB.1GeneralThe supplier of a protocol implementation which is claimed to conform to the Fixed radio Termination (FT)specific requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] shall verify that his particular (NWK,DLC, MAC and PHL) layer protocol implementation meets the Profile RL for this layer. For this, he shallcomplete a copy of the corresponding layer PICS proforma contained in annex A of ETS 300 476 parts 4,5, 6 and 7 [12], [13], [14], and [15] updated with the requirements from this annex.B.1.1Profile Requirement List (Profile RL)The profile requirement list (profile RL) for the NWK, DLC, MAC and PHL layers as defined in this annex isbased on ETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14] and [15]. For every capability listed inETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14] and [15], the profile requirements are expressed byrestriction upon allowed support answers in ETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14] and [15]. TheProfile RL is produced by copying selected tables from ETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14]and [15], removing the column(s) to be completed by the supplier, and adding a new set of columns givingthe new profile requirements, both in terms of the status and allowed values. The tables are referenced bypreceding it with the relevant reference standard.Profile status columnThe standardized symbols for the status column are as follows:m or Mmandatory - the capability is required to be supported;o or Ooptional - the capability may be supported or not;n/a or N/Anot applicable - in the given context, it is impossible to use the capability;x or Xprohibited (excluded) - there is a requirement not to use this capability in thegiven context;o.i or O.iqualified optional - for mutually exclusive or selectable options from a set. "i" isan integer which identifies an unique group of related optional items and the logicof their selection which is defined immediately following the table;ci or Ciconditional - the requirement on the capability ("m", "o", "x" or "n/a") depends onthe support of other optional or conditional items. "i" is an integer identifying anunique conditional status expression which is defined immediately following thetable or which is defined in the general condition table below;i or Iout-of-scope - this capability is outside the scope of the given specification, andhence irrelevant and not subject to conformance testing. This status is inparticular applicable for data fields which are reserved for future use. Thestructure of such fields has to be supported, but the value is undefined and thusto be ignored.Reference columnThe reference column gives reference to ETS 300 434-1 [10] or ETS 300 434-2 [11] stated by using thereference standard preceding the number of the subclause, except where explicitly stated otherwise.SIST ETS 300 705-2:2000
Page 19ETS 300 705-2: June 1997B.1.2General conditionsTable B.1: General condition tableCondition identifierCondition definitionnote 1The status of the relevant item is exactly as the status of this item inETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14] and [15]. The item has beenincluded as the Profile reference column include reference to the profile thatdescribes the item more in details.B.2Requirement lists on DECT protocolsB.2.1Requirement list on DECT NWK layerB.2.1.1Network entitiesTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following tableindicates the change of status for support of entities.Table B.2: ETS 300 476-4 [12], Table A.12 EntityItemEntity nameProfile ReferenceProfile Status1Call control (CC)ETS 300 434-1 [10],subclause 5.2.4.1m2Call Independent Supplementary Services (CISS)ETS 300 434-1 [10],subclause 5.2.4.1o6Link control entity (LCE)ETS 300 434-2 [11],subclause 5.2mB.2.1.2Network featuresB.2.1.2.1CC featuresTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following tableindicates the change of status for support of features.SIST ETS 300 705-2:2000
Page 20ETS 300 705-2: June 1997Table B.3: ETS 300 476-4 [12], Table A.13 CC featuresItemFeature nameProfile ReferenceProfile Status3Control of supervisory tonesETS 300 434-2 [11],subclause 4.1.9o5Dialled digits (basic)ETS 300 434-2 [11],subclause 4.1.5m6Dialled digits additionalETS 300 434-2 [11],subclause 4.1.6o7Dialling delimiterETS 300 434-2 [11],subclause 4.1.7o17Incoming callETS 300 434-2 [11],subclause 4.1.8m19Off hookETS 300 434-2 [11],subclause 4.1.3m20On hook (full release)ETS 300 434-2 [11],subclause 4.1.4m21Outgoing callETS 300 434-2 [11],subclause 4.1.1m26Signalling of display charactersETS 300 434-2 [11],subclause 4.1.10o27Selection of bearer serviceETS 300 434-2 [11],subclause 4.1.12mB.2.1.2.2SS features (services)To express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following tableindicates the change of status for support of supplementary services.SIST ETS 300 705-2:2000
Page 21ETS 300 705-2: June 1997Table B.4: ETS 300 476-4 [12], Table A.15 SS features (services)ItemFeature nameProfile ReferenceProfile Status1Advice of Charge (AOC)ETS 300 434-2 [11],subclause 4.1.27o3Call Deflection (CD)ETS 300 434-2 [11],subclause 4.1.31o4Call Forwarding Busy (CFB)ETS 300 434-2 [11],subclause 4.1.39o5Call Forwarding No Reply (CFNR)ETS 300 434-2 [11],subclause 4.1.39o6Call Forwarding Unconditional (CFU)ETS 300 434-2 [11],subclause 4.1.39o7Call Waiting (CW)ETS 300 434-2 [11],subclause 4.1.24o8Calling Line Identification Presentation (CLIP)ETS 300 434-2 [11],subclause 4.1.17o9Calling Line Identification Restriction (CLIR)ETS 300 434-2 [11],subclause 4.1.18o10Closed User Group (CUG)ETS 300 434-2 [11],subclause 4.1.26o11Completion of Calls to Busy Subscriber (CCBS)ETS 300 434-2 [11],subclause 4.1.36o12Call Hold(CH)ETS 300 434-2 [11],subclause 4.1.25o13Conference call, add-on (CONF)ETS 300 434-2 [11],subclause 4.1.29o14Connected Line identification Presentation (COLP)ETS 300 434-2 [11],subclause 4.1.19o15Connected Line identification Restriction (COLR)ETS 300 434-2 [11],subclause 4.1.20o21Direct Dialling In (DDI)ETS 300 434-2 [11],subclause 4.1.22o22Explicit Call Transfer (ECT)ETS 300 434-2 [11],subclause 4.1.35o24Freephone (FPH)ETS 300 434-2 [11],subclause 4.1.37o26Hold call (PT to FT)ETS 300 434-2 [11],subclause 4.1.14o29Malicious Call Identification (MCID)ETS 300 434-2 [11],subclause 4.1.28o30Multiple Subscriber Number (MSN)ETS 300 434-2 [11],subclause 4.1.21o34Re-connection of held call (PT to FT)ETS 300 434-2 [11],subclause 4.1.39o36Selection of required teleserviceETS 300 434-2 [11],subclause 4.1.11o39Subaddressing (SUB)ETS 300 434-2 [11],subclause 4.1.23o40Terminal Portability (TP)ETS 300 434-1 [10],subclause 5.2.2.5.8i41Three-Party (3PTY)ETS 300 434-2 [11],subclause 4.1.30o42User to User Signalling (UUS)ETS 300 434-2 [11],subclauses 4.1.32, 4.1.33,4.1.34oSIST ETS 300 705-2:2000
Page 22ETS 300 705-2: June 1997B.2.1.2.3LCE featuresTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following tableindicates the change of status for support of LCE features.Table B.5: ETS 300 476-4 [12], Table A.16 LCE featuresItemFeature nameProfile ReferenceProfile Status1Connection oriented Link control (Link control)ETS 300 434-2 [11],subclause 5.2mB.2.1.3ProceduresTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following tableindicates the change of status for support of the procedures.Table B.6: ETS 300 476-4 [12], Table A.18 CC proceduresItemProcedure nameProfile ReferenceProfile Status1cc_outgoing_normal_call_requestETS 300 434-2 [11],subclause 5.2m5cc_outgoing_connection_of_U_planeETS 300 434-2 [11],subclause 5.2m6cc_outgoing_overlap_sendingETS 300 434-2 [11],subclause 5.2m7cc_outgoing_call_proceedingETS 300 434-2 [11],subclause 5.2m8cc_outgoing_call_confirmationETS 300 434-2 [11],subclause 5.2m9cc_outgoing_call_connectionETS 300 434-2 [11],subclause 5.2m12cc_incoming_connection_of_U_planeETS 300 434-2 [11],subclause 5.2m15cc_incoming_call_confirmationETS 300 434-2 [11],subclause 5.2m16cc_incoming_call_connectionETS 300 434-2 [11],subclause 5.2m17cc_sending_terminal_capabilityETS 300 434-2 [11],subclause 5.2m19cc_call_informationETS 300 434-2 [11],subclause 5.2o20cc_normal_call_releaseETS 300 434-2 [11],subclause 5.2m22cc_abnormal_call_releaseETS 300 434-2 [11],subclause 5.2m23cc_release_collisionsETS 300 434-2 [11],subclause 5.2m32cc_timer_f_cc_03_mgtETS 300 434-2 [11],subclause 5.2m33cc_timer_f_cc_04_mgtETS 300 434-2 [11],subclause 5.2see table B.1SIST ETS 300 705-2:2000
Page 23ETS 300 705-2: June 1997Table B.7: ETS 300 476-4 [12], Table A.20 SS protocolsItemSS protocol nameProfile ReferenceProfile Status1crss_keypad_protocolETS 300 434-1 [10], subclause5.2.2.1o3crss_functional_protocol_smcETS 300 434-1 [10], subclause5.2.2.3o4ciss_keypad_protocolETS 300 434-1 [10], subclause5.2.2.2i7crss_functional_protocol_ciecETS 300 434-1 [10], subclause5.2.2.3o8ciss_functional_protocol_ciecETS 300 434-1 [10], subclause5.2.2.4.1oTable B.8: ETS 300 476-4 [12], Table A.23 LCE proceduresItemProcedure nameProfile ReferenceProfile Status1lce_direct_pt_init_link_establishmentETS 300 434-2 [11],subclause 5.2m2lce_indirect_ft_init_link_establishmentETS 300 434-2 [11],subclause 5.2m3lce_direct_ft_init_link_establishmentETS 300 434-2 [11],subclause 5.2o4lce_link_maintenanceETS 300 434-2 [11],subclause 5.2m7lce_link_releaseETS 300 434-2 [11],subclause 5.2m11lce_timer_lce_01_mgtETS 300 434-2 [11],subclause 5.2m12lce_timer_lce_02_mgtETS 300 434-2 [11],subclause 5.2m13lce_timer_lce_03_mgtETS 300 434-2 [11],subclause 5.2mSIST ETS 300 705-2:2000
Page 24ETS 300 705-2: June 1997B.2.1.4MessagesTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following tablesindicate the change of status for support of messages.B.2.1.4.1CC messagesTable B.9: ETS 300 476-4 [12], Table A.25 CC receiving (P to F) messagesItemCC receiving (P to F)Message nameProfile ReferenceProfile Status1CC-SETUPETS 300 434-1 [10],subclause 5.2.4.2m2CC-INFOrmationETS 300 434-1 [10],subclause 5.2.4.2m5CC-ALERTINGETS 300 434-1 [10],subclause 5.2.4.2m6CC-CONNECTETS 300 434-1 [10],subclause 5.2.4.2m8CC-RELEASEETS 300 434-1 [10],subclause 5.2.4.2m9CC-RELEASE-COMpleteETS 300 434-1 [10],subclause 5.2.4.2m14IWU-INFOrmationETS 300 434-1 [10],subclause 5.2.4.2iTable B.10: ETS 300 476-4 [12], Table A.26 CC sending (F to P) messagesItemCC sending (F to P)Message nameProfile ReferenceProfile Status1CC-SETUPETS 300 434-1 [10],subclause 5.2.4.1m2CC-INFOrmationETS 300 434-1 [10],subclause 5.2.4.1m3CC-SETUP-ACKnowledgeETS 300 434-1 [10],subclause 5.2.4.1m4CC-CALL-PROCeedingETS 300 434-1 [10],subclause 5.2.4.1m5CC-ALERTINGETS 300 434-1 [10],subclause 5.2.4.1m6CC-CONNECTETS 300 434-1 [10],subclause 5.2.4.1m7CC-CONNECT-ACKnowledgeETS 300 434-1 [10],subclause 5.2.4.1m8CC-RELEASEETS 300 434-1 [10],subclause 5.2.4.1m9CC-RELEASE-COMpleteETS 300 434-1 [10],subclause 5.2.4.1mSIST ETS 300 705-2:2000
Page 25ETS 300 705-2: June 1997B.2.1.4.2CRSS and CISS messagesTable B.11: ETS 300 476-4 [12], Table A.86 CRSS & CISS messages receiving (P to F)ItemCRSS & CISS messages receiving (P to F)Message nameProfile ReferenceProfile Status1FACILITYETS 300 434-2 [11],subclause 5.2.4.2o2HOLDETS 300 434-2 [11],subclause 5.2.4.2c11015RETRIEVEETS 300 434-2 [11],subclause 5.2.4.2c11018CISS-REGISTERETS 300 434-2 [11],subclause 5.2.4.2o9CISS-RELEASE-COMpleteETS 300 434-2 [11],subclause 5.2.4.2oc1101:IF ETS 300 476-4 [12] Table A.15/12 THEN m ELSE oTable B.12: ETS 300 476-4 [12], Table A.87 CRSS & CISS messages sending (F to P)ItemCRSS & CISS messages sending (F to P)Message nameProfile ReferenceProfile Status1FACILITYETS 300 434-2 [11],subclause 5.2.4.1o3HOLD-ACKnowledgeETS 300 434-2 [11],subclause 5.2.4.1c12014HOLD-REJECTETS 300 434-2 [11],subclause 5.2.4.1c12016RETRIEVE-ACKnowledgeETS 300 434-2 [11],subclause 5.2.4.1c12017RETRIEVE-REJECTETS 300 434-2 [11],subclause 5.2.4.1c12018CISS-REGISTERETS 300 434-2 [11],subclause 5.2.4.1o9CISS-RELEASE-COMpleteETS 300 434-2 [11],subclause 5.2.4.1oc1201:IF ETS 300 476-4 [12] Table A.15/12 THEN m ELSE oB.2.1.4.3LCE messagesTable B.13: ETS 300 476-4 [12], Table A.126 LCE message receiving (P to F)ItemLCE message receiving (P to F)Profile ReferenceProfile Status1LCE-PAGE-RESPONSEETS 300 434-1 [10], figure 22mTable B.14: ETS 300 476-4 [12], Table A.127 LCE message sending (F to P)ItemLCE message sending (F to P)Profile ReferenceProfile Status2LCE-PAGE-REJECTETS 300 434-1 [10], figure 22m3LCE-REQUEST-PAGE shortETS 300 434-1 [10], figure 22m4LCE-REQUEST-PAGE longETS 300 434-1 [10], figure 22mSIST ETS 300 705-2:2000
Page 26ETS 300 705-2: June 1997B.2.2Requirement list on DECT DLC layerB.2.2.1ServicesTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] the following tableindicates the change of status for support of data link services.Table B.15: ETS 300 476-5 [13], Table A.9 Data link servicesItemData link servicesProfile ReferenceProfile Status1C-plane servicesETS 300 434-1 [10],subclause 6.1m2U-plane servicesETS 300 434-1 [10],subclause 6.2c1501c1501:IF C.9/1 OR C.9/2 THEN m ELSE oB.2.2.1.1C-plane servicesTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] the following tableindicates the change of status for support of C-plane services.Table B.16: ETS 300 476-5 [13], Table A.10 C-plane servicesItemC-plane servicesProfile ReferenceProfile Status2Class A serviceETS 300 434-2 [11],subclause 6.1.1m4Broadcast serviceETS 300 434-2 [11],subclause 6.1.2mB.2.2.1.2U-plane servicesTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] the following tableindicates the change of status for support of U-plane services.Table B.17: ETS 300 476-5 [13], Table A.11 U-plane servicesItemU-plane servicesProfile ReferenceProfile Status1LU1 - Transparent Unprotected serviceETS 300 434-2 [11],subclause 6.2c17018LU7 - 64kbit/s data bearer serviceETS 300 434-2 [11],subclause 6.2c1702c1701:IF C.9/1 OR C.9/2 THEN m ELSE oc1702:IF C.9/3 THEN m ELSE oB.2.2.2ProceduresB.2.2.2.1Generic signalling proceduresTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] the following tableindicates the change of status for support of Generic signalling procedures.SIST ETS 300 705-2:2000
Page 27ETS 300 705-2: June 1997Table B.18: ETS 300 476-5 [13], Table A.13 Generic signalling proceduresItemGeneric signalling proceduresProfile ReferenceProfile Status2CS channel fragmentation and recombinationETS 300 434-2 [11],subclause 6.1.1mB.2.2.2.2Class A proceduresTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] the following tableindicates the change of status for support of Class A procedures.Table B.19: ETS 300 476-5 [13], Table A.14 Class A proceduresItemClass A proceduresProfile ReferenceProfile Status1Class A link establishmentETS 300 434-2 [11],subclause 6.1.1m2Class A acknowledged information transferETS 300 434-2 [11],subclause 6.1.1m3Class A link releaseETS 300 434-2 [11],subclause 6.1.1m4Class A link re-establishmentETS 300 434-2 [11],subclause 6.1.1mB.2.2.2.3Broadcast proceduresTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] the following tableindicates the change of status for support of Broadcast procedures.Table B.20: ETS 300 476-5 [13], Table A.16 Broadcast proceduresItemBroadcast proceduresProfile ReferenceProfile Status1Normal operationETS 300 434-2 [11],subclause 7.1.2mB.2.2.2.4LU1 proceduresTo express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] the following tableindicates the change of status for support of LU1 procedures.Table B.21: ETS 300 476-5 [13], Table A.17 LU1 proceduresItemLU1 proceduresProfile ReferenceProfile Status1Class 0/min_delayETS 300 434-2 [11],subclause 6.2m3FU1 frame operationETS 300 434-2 [11],subclause 6.2see table B.1B.2.2.3ParametersB.2.2.3.1LU1 pa
...
SLOVENSKI STANDARD
01-januar-2000
'LJLWDOQHL]EROMãDQHEUH]YUYLþQHWHOHNRPXQLNDFLMH '(&7 'LJLWDOQRRPUHåMH]
LQWHJULUDQLPLVWRULWYDPL ,6'1 9]DMHPQRGHORYDQMH'(&7,6'1YREOLNLNRQþQHJD
VLVWHPD3URILOL]MDYHRVNODGQRVWLL]YHGEH ,&6 GHO )LNVQDUDGLMVND
]DNOMXþLWHY )7
Digital Enhanced Cordless Telecommunications (DECT); Integrated Services Digital
Network (ISDN); DECT/ISDN interworking for end system configuration; Profile
Implementation Conformance Statement (ICS); Part 2: Fixed radio Termination (FT)
Ta slovenski standard je istoveten z: ETS 300 705-2 Edition 1
ICS:
33.070.30 'LJLWDOQHL]EROMãDQH Digital Enhanced Cordless
EUH]YUYLþQHWHOHNRPXQLNDFLMH Telecommunications (DECT)
'(&7
33.080 Digitalno omrežje z Integrated Services Digital
integriranimi storitvami Network (ISDN)
(ISDN)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN ETS 300 705-2
TELECOMMUNICATION June 1997
STANDARD
Source: ETSI EP-DECT Reference: DE/DECT-040045-2
ICS: 33.020
Key words: DECT, ISDN, ICS, radio, testing
Digital Enhanced Cordless Telecommunications (DECT);
Integrated Services Digital Network (ISDN);
DECT/ISDN interworking for end system configuration;
Profile Implementation Conformance Statement (ICS);
Part 2: Fixed radio Termination (FT)
ETSI
European Telecommunications Standards Institute
ETSI Secretariat
Postal address: F-06921 Sophia Antipolis CEDEX - FRANCE
Office address: 650 Route des Lucioles - Sophia Antipolis - Valbonne - FRANCE
X.400: c=fr, a=atlas, p=etsi, s=secretariat - Internet: secretariat@etsi.fr
Tel.: +33 4 92 94 42 00 - Fax: +33 4 93 65 47 16
Copyright Notification:
No part may be reproduced except as authorized by written permission. The copyright and the
foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 1997. All rights reserved.
Page 2
ETS 300 705-2: June 1997
Whilst every care has been taken in the preparation and publication of this document, errors in content,
typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to
"ETSI Editing and Committee Support Dept." at the address shown on the title page.
Page 3
ETS 300 705-2: June 1997
Contents
Foreword .7
1 Scope.9
2 Normative references.9
3 Definitions and abbreviations .11
3.1 Definitions.11
3.2 Abbreviations .11
4 Conformance requirement concerning Profile ICS.11
Annex A (normative): System Conformance Statement (SCS) proforma for DECT FT IAP.14
A.1 Identification.14
A.1.1 Description of the system.14
A.1.2 Supplier of the system .14
A.1.3 Client identification.15
A.1.4 Contact person identification.15
A.1.5 Signature of the client or of the supplier.15
A.2 Protocol identification.16
A.3 Profile identification.16
A.4 Combination description table.16
A.5 Configurability table .16
A.6 Additional information.17
Annex B (normative): Requirement lists for DECT FT IAP .18
B.1 General .18
B.1.1 Profile Requirement List (Profile RL).18
B.1.2 General conditions.19
B.2 Requirement lists on DECT protocols.19
B.2.1 Requirement list on DECT NWK layer .19
B.2.1.1 Network entities.19
B.2.1.2 Network features.19
B.2.1.2.1 CC features.19
B.2.1.2.2 SS features (services).20
B.2.1.2.3 LCE features .22
B.2.1.3 Procedures .22
B.2.1.4 Messages.24
B.2.1.4.1 CC messages.24
B.2.1.4.2 CRSS and CISS messages .25
B.2.1.4.3 LCE messages.25
B.2.2 Requirement list on DECT DLC layer .26
B.2.2.1 Services.26
B.2.2.1.1 C-plane services.26
B.2.2.1.2 U-plane services .26
B.2.2.2 Procedures .26
Page 4
ETS 300 705-2: June 1997
B.2.2.2.1 Generic signalling procedures .26
B.2.2.2.2 Class A procedures.27
B.2.2.2.3 Broadcast procedures .27
B.2.2.2.4 LU1 procedures .27
B.2.2.3 Parameters .27
B.2.2.3.1 LU1 parameters.27
B.2.2.4 Messages .28
B.2.2.4.1 C-plane PDUs.28
B.2.3 Requirement list on DECT MAC layer.28
B.2.3.1 Services.28
B.2.3.1.1 Connection oriented control services.28
B.2.3.1.2 Broadcast control services.29
B.2.3.1.3 Multiplexing services.29
B.2.3.2 Procedures .31
B.2.3.2.1 Connection setup procedures.31
B.2.3.2.2 Connection data transfer procedures.31
B.2.3.2.3 Connection release procedures.31
B.2.3.2.4 Broadcast procedures .31
B.2.3.2.5 CSF multiplexing procedures.32
B.2.3.2.6 Layer management procedures.32
B.2.3.3 Other capabilities.32
B.2.3.4 Messages .33
B.2.3.4.1 A-field header - B-field identification.33
B.2.3.4.2 Paging tail messages supported.33
B.2.3.4.3 MAC control messages supported.34
B.2.3.4.4 B-field messages supported.34
B.2.3.5 MAC messages format and field value.36
B.2.3.5.1 QT - Fixed part capability .36
B.2.4 Requirement list on DECT PHL layer.36
B.2.5 Requirement list on ISDN L3 layer tables.37
B.2.5.1 ISDN L3 layer primary access tables.37
B.2.5.2 ISDN L3 layer basic access tables.37
B.2.6 Requirement list on ISDN L2 layer tables.37
B.2.6.1 ISDN L2 layer primary access tables.37
B.2.6.2 ISDN L2 layer basic access tables.37
B.2.7 Requirement list on ISDN L1 layer tables.37
B.2.7.1 ISDN L1 layer primary access tables.37
B.2.7.2 ISDN L1 layer basic access tables.37
Annex C (normative): Profile specific ICS proforma for DECT FT IAP.38
C.1 Guidance for completing the profile specific proforma.38
C.1.1 Purposes and structure.38
C.1.2 Instructions for completing the Profile specific ICS .40
C.2 Identification of the implementation.40
C.2.1 Date of statement.40
C.2.2 Identification of the implementation.40
C.2.3 Contact person identification.40
C.2.4 Relationship with the System Conformance Statement (SCS).41
C.3 Identification of the profile.41
C.3.1 Defect report numbers and amendments implemented.41
C.3.2 Addenda implemented.42
C.4 Profile ICS proforma tables .42
C.4.1 Global statement of conformance .42
C.4.2 Profile ICS features tables .42
C.4.3 Profile ICS IWU tables.43
C.4.3.1 IWU procedures .43
Page 5
ETS 300 705-2: June 1997
C.4.3.2 IWU messages mapping .45
C.4.4 Profile ICS NWK layer tables.53
C.4.5 Profile ICS DLC layer tables.53
C.4.6 Profile ICS MAC layer tables.53
Annex D (normative): Messages redefinition for DECT CI FT PICS proforma.54
D.1 Description.54
D.2 CC messages .54
D.3 Connection Related Supplementary Service (CRSS) and Connection Independent Supplementary
Service (CISS) messages .62
D.4 Information elements.66
D.5 Timers and constants support.69
History .70
Page 6
ETS 300 705-2: June 1997
Blank page
Page 7
ETS 300 705-2: June 1997
Foreword
This European Telecommunication Standard (ETS) has been produced by the Digital Enhanced Cordless
Telecommunications (DECT) Project of the European Telecommunications Standards Institute (ETSI).
This ETS comprises two parts:
Part 1: "Portable radio Termination (PT)".
Part 2: "Fixed radio Termination (FT)".
Annex A of this ETS contains the System Conformance Statement (SCS) proforma for the DECT FT ISDN
Access Profile (IAP).
Annex B of this ETS contains the requirement lists for the DECT FT IAP.
Annex C of this ETS contains the specific ICS proforma for the DECT FT IAP.
Transposition dates
Date of adoption: 6 June 1997
Date of latest announcement of this ETS (doa): 30 September 1997
Date of latest publication of new National Standard
or endorsement of this ETS (dop/e): 31 March 1998
Date of withdrawal of any conflicting National Standard (dow): 31 March 1998
Page 8
ETS 300 705-2: June 1997
Blank page
Page 9
ETS 300 705-2: June 1997
1 Scope
This European Telecommunication Standard (ETS) provides the Profile Implementation Conformance
Statement (Profile ICS) proforma for the Digital Enhanced Cordless Telecommunications DECT/ISDN inter-
working for end system configuration Profile at the Fixed Termination as defined in ETS 300 434-1 [10],
and ETS 300 434-2 [11] in compliance with the relevant requirements and in accordance with the relevant
guidance given in ISO/IEC 9646-7 [18].
The supplier of an implementation which is claimed to conform to ETS 300 434-1 [10] and
ETS 300 434-2 [11] is required to complete a copy of the PICS proforma ETS 300 476 parts 4, 5, 6 and
7 [12], [13], [14] and [15], with the replacements provided by the requirement lists given in annex B of this
ETS, as well as a copy of the specific ICS proforma provided in the annex C of this ETS.
2 Normative references
This ETS incorporates, by dated or undated reference, provisions from other publications. These normative
references are cited at the appropriate places in the text and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this ETS
only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies.
[1] ETS 300 175-1: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 1: Overview".
[2] ETS 300 175-2: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 2: Physical layer (PHL)".
[3] ETS 300 175-3: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 3: Medium Access Control (MAC) layer".
[4] ETS 300 175-4: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 4: Data Link Control (DLC) layer".
[5] ETS 300 175-5: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 5: Network (NWK) layer".
[6] ETS 300 175-6: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 6: Identities and addressing".
[7] ETS 300 175-7: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 7: Security features".
[8] ETS 300 175-8: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 8: Speech coding and transmission".
[9] ETS 300 175-9: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Part 9: Public Access Profile (PAP)".
[10] ETS 300 434-1: "Digital Enhanced Cordless Telecommunications (DECT) and
Integrated Services Digital Network (ISDN) interworking for end system
configuration; Part 1: Interworking specification".
[11] ETS 300 434-2: "Digital Enhanced Cordless Telecommunications (DECT) and
Integrated Services Digital Network (ISDN) interworking for end system
configuration; Part 2: Access profile".
[12] ETS 300 476-4: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Protocol Implementation Conformance Statement
(PICS) proforma; Part 4: Network (NWK) layer - Fixed radio Termination (FT)".
Page 10
ETS 300 705-2: June 1997
[13] ETS 300 476-5: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Protocol Implementation Conformance Statement
(PICS) proforma; Part 5: Data Link Control (DLC) layer - Fixed radio Termination
(FT)".
[14] ETS 300 476-6: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Protocol Implementation Conformance Statement
(PICS) proforma; Part 6: Medium Access Control (MAC) layer - Fixed radio
Termination (FT)".
[15] ETS 300 476-7: "Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI); Protocol Implementation Conformance Statement
(PICS) proforma; Part 7: Physical layer".
[16] ISO/IEC 9646-1 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 1:
General concepts". (See also CCITT Recommendation X.290 (1991)).
[17] ISO/IEC 9646-6 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 6:
Protocol profile test specification".
[18] ISO/IEC 9646-7 (1991): "Information technology - Open Systems
Interconnection - Conformance testing methodology and framework - Part 7:
Implementation conformance statement".
[19] ETS 300 406: "Methods for Testing and Specification (MTS); Protocol and
profile conformance testing specifications; Standardization methodology".
[20] ETS 300 403-1: "Integrated Services Digital Network (ISDN); Digital Subscriber
Signalling System No. one (DSS1) protocol; Signalling network layer for
circuit-mode basic call control; Part 1: Protocol specification [ITU-T
Recommendation Q.931 (1993), modified]".
[21] ETS 300 403-3: "Integrated Services Digital Network (ISDN); Digital Subscriber
Signalling System No. one (DSS1) protocol; Signalling network layer for
circuit-mode basic call control; Part 3: Protocol Implementation Conformance
Statement (PICS) proforma specification".
[22] ETS 300 402-2: "Integrated Services Digital Network (ISDN); Digital Subscriber
Signalling System No. one (DSS1) protocol; Data link layer; Part 2: General
protocol specification [ITU-T Recommendation Q.921 (1993), modified]".
[23] ETS 300 402-4: "Integrated Services Digital Network (ISDN); Digital Subscriber
Signalling System No. one (DSS1) protocol; Data link layer; Part 4: Protocol
Implementation Conformance Statement (PICS) proforma specification for the
general protocol".
[24] ETS 300 011 (1992): "Integrated Services Digital Network (ISDN); Primary rate
user-network interface; Layer 1 specification and test principles".
[25] ETS 300 011/A2: "Amendment 2 to ETS 300 011 (1992), adding a SCS, a PICS
and a PIXIT for interface points I and I ".
a b
[26] ETS 300 012 (1992): "Integrated Services Digital Network (ISDN); Basic user-
network interface; Layer 1 specification and test principles".
[27] ETS 300 012/A2: "Amendment 2 to ETS 300 012 (1992), adding a SCS, a PICS
and a PIXIT for interface points I and I ".
a b
Page 11
ETS 300 705-2: June 1997
[28] ETS 300 196-1: "Integrated Services Digital Network (ISDN); Generic functional
protocol for the support of supplementary services; Digital Subscriber Signalling
System No. one (DSS1) protocol; Part 1: Protocol specification".
[29] ETS 300 196-2: "Integrated Services Digital Network (ISDN); Generic functional
protocol for the support of supplementary services; Digital Subscriber Signalling
System No. one (DSS1) protocol; Part 2: Protocol Implementation Conformance
Statement (PICS) proforma specification".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of this ETS, the following terms and definitions apply:
a) the terms defined in ISO/IEC 9646-7 [18];
b) the definitions in ETS 300 434-1 [10] and ETS 300 434-2 [11]; and
c) the following terms defined in ISO/IEC 9646-1 [16]:
- PICS proforma;
- Profile Implementation Conformance Statement (Profile ICS).
3.2 Abbreviations
For the purposes of this ETS, the abbreviations defined in ISO/IEC 9646-1 [16], the abbreviations defined
in ETS 300 434-1 [10] and ETS 300 434-2 [11] apply.
4 Conformance requirement concerning Profile ICS
The supplier of a protocol implementation which is claimed to conform to the Fixed Termination specific
requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] shall:
- verify that his protocol implementation meets the Profile Requirements Lists (Profile RLs) for each
DECT protocol layer, contained in annex B of this ETS;
- complete a copy of the Profile specific ICS proforma provided in annex C;
- complete a copy of the System Conformance Statement (SCS) proforma provided in annex A; and
- provide the information necessary to identify both the supplier and the implementation.
Tables 1 and 2 provide guidance to indicate how to fulfil the PICS proforma required for the profile.
Page 12
ETS 300 705-2: June 1997
Table 1: DECT PICS proforma table
PICS Tables Change
ETS 300 476-4 [12] A.12 Status column updated by RL subclause B.2.1.1
A.13 to A.16 Status column updated by RL subclause B.2.1.2
A.18 to A.20 Status column updated by RL subclause B.2.1.3
A.23 to A.24 Status column updated by RL subclause B.2.1.3
A.25 to A.26 Status column updated by RL subclause B.2.1.4.1
A.51 to A.55 Status column updated by RL subclause B.2.1.4.2
A.58 Status column updated by RL subclause B.2.1.4.2
A.61 to A.71 Status column updated by RL subclause B.2.1.4.2
A.73 to A.74 Status column updated by RL subclause B.2.1.4.2
A.76 to A.78 Status column updated by RL subclause B.2.1.4.2
A.82 Status column updated by RL subclause B.2.1.4.2
A.85 Status column updated by RL subclause B.2.1.4.2
A.86 to A.87 Status column updated by RL subclause B.2.1.4.3
A.126 to A.129 Status column updated by RL subclause B.2.1.4.4
A.27 to A.41 Tables replaced by annex D subclause D.2
A.88 to A.89 Tables replaced by annex D subclause D.2
A.95 Tables replaced by annex D subclause D.2
A.101 to A.105 Tables replaced by annex D subclause D.2
A.209 Tables replaced by annex D subclause D.3
A.258 Tables replaced by annex D subclause D.3
A.285 Tables replaced by annex D subclause D.3
A.314 Tables replaced by annex D subclause D.4
All other tables Unchanged
ETS 300 476-5 [13] A.9 to A.12 Status column updated by RL subclause B.2.2.1
A.13 to A.14 Status column updated by RL subclause B.2.2.2
A.16 to A.17 Status column updated by RL subclause B.2.2.2
A.28 to A.29 Status column updated by RL subclause B.2.2.2
A.32 Status column updated by RL subclause B.2.2.2
A.38 Status column updated by RL subclause B.2.2.3
A.54 Status column updated by RL subclause B.2.2.4
All other tables Unchanged
ETS 300 476-6 [14] A.9 to A.12 Status column updated by RL subclause B.2.3.1
A.14 to A.15 Status column updated by RL subclause B.2.3.1
A.19 to A.25 Status column updated by RL subclause B.2.3.1
A.26 to A.28 Status column updated by RL subclause B.2.3.2
A.30 to A.33 Status column updated by RL subclause B.2.3.2
A.36 to A.37 Status column updated by RL subclause B.2.3.2
A.38 to A.39 Status column updated by RL subclause B.2.3.3
A.50 to A.51 Status column updated by RL subclause B.2.3.4
A.57 to A.60 Status column updated by RL subclause B.2.3.4
A.69 to A.70 Status column updated by RL subclause B.2.3.4
A.88 Status column updated by RL subclause B.2.3.5
All other tables Unchanged
ETS 300 476-7 [15] A.15 Status column updated by RL subclause B.2.4
All other tables Unchanged
Page 13
ETS 300 705-2: June 1997
Table 2: ISDN PICS proforma table
PICS Tables Change
ETS 300 403-3 [21] All tables Unchanged
ETS 300 402-4 [23] All tables Unchanged
ETS 300 011/A2 [25] All tables Unchanged
ETS 300 012/A2 [27] All tables Unchanged
ETS 300 196-2 [29] All tables Unchanged
Page 14
ETS 300 705-2: June 1997
Annex A (normative): System Conformance Statement (SCS) proforma for
DECT FT IAP
Notwithstanding the provisions of the copyright clause related to the text of this ETS, ETSI grants that
users of this ETS may freely reproduce the SCS proforma in this annex so that it can be used for its
intended purposes and may further publish the completed SCS.
A.1 Identification
A.1.1 Description of the system
Table A.1: Description of the system
Product name:
Hardware version number:
Software version number:
CPU Type:
Bus-System:
Operating System Name:
Operating System version number:
Additional:
A.1.2 Supplier of the system
Table A.2: Supplier of the system
Company:
Street:
Postal Code / City:
Country:
Page 15
ETS 300 705-2: June 1997
A.1.3 Client identification
If different from the supplier.
Table A.3: Client identification
Company:
Street:
Postal Code / City:
Country:
A.1.4 Contact person identification
Table A.4: Contact person identification
Name:
Telephone:
Fax:
Telex:
E-Mail:
A.1.5 Signature of the client or of the supplier
Table A.5: Signature of the client or of the supplier
Name:
Position:
Signature:
Date:
Page 16
ETS 300 705-2: June 1997
A.2 Protocol identification
This table identifies the protocols that have to be supported. The PCTR Reference column may be used to
refer to any PCTR that have been obtained for these protocols in this system.
Table A.6: Protocol identification
Item Protocol name Specification PICS PCTR
Reference Reference Reference
Pr1 ISDN L3 layer ETS 300 403-1 [20] ETS 300 403-3 [21]
Pr2 ISDN L2 layer ETS 300 402-2 [22] ETS 300 402-4 [23]
Pr3 ISDN L1 layer ETS 300 011 [24] ETS 300 011/A2 [25]
ETS 300 012 [26] ETS 300 012/A2 [27]
Pr4 ISDN Generic Functional ETS 300 196 [28] ETS 300 196-2 [29]
Pr5 DECT NWK layer ETS 300 175-5 [5] ETS 300 476-4 [12]
Pr6 DECT DLC layer ETS 300 175-4 [4] ETS 300 476-5 [13]
Pr7 DECT MAC layer ETS 300 175-3 [3] ETS 300 476-6 [14]
Pr8 DECT PH layer ETS 300 175-2 [2] ETS 300 476-7 [15]
A.3 Profile identification
This table identifies the profiles that have to be supported. The SCTR Reference column may be used to
refer to any SCTR that have been obtained for these profiles in this system.
Table A.7: Profile identification
Item Profile identifier Specification Profile specific ICS SCTR Reference
Reference Reference
Po1 Generic Access Profile (GAP) ETS 300 444 ETS 300 474
Po2 ISDN Access Profile (IAP) ETS 300 434 ETS 300 705
A.4 Combination description table
This clause identifies which combinations of protocols are allowed cause of supporting these profiles, and
which combinations not covered by the profile are also supported.
Table A.8: Combination table
Item Profile Protocol
c1 Po1 Pr5, Pr6, Pr7, Pr8
c2 Po2 Po1, Pr1, Pr2, Pr3, Pr4
A.5 Configurability table
This clause identifies what kind of configuration or reconfiguration is needed in order to use each of the
identified combinations.
Table A.9: Configurability table
Combination Available always? Available by dynamic Available by static
reconfiguration? reconfiguration?
c1
c2
Page 17
ETS 300 705-2: June 1997
A.6 Additional information
Any additional information which is relevant for the product may be given here (e.g. information that is
needed for further certification: quality system used, available certificates, etc.).
Page 18
ETS 300 705-2: June 1997
Annex B (normative): Requirement lists for DECT FT IAP
B.1 General
The supplier of a protocol implementation which is claimed to conform to the Fixed radio Termination (FT)
specific requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11] shall verify that his particular (NWK,
DLC, MAC and PHL) layer protocol implementation meets the Profile RL for this layer. For this, he shall
complete a copy of the corresponding layer PICS proforma contained in annex A of ETS 300 476 parts 4,
5, 6 and 7 [12], [13], [14], and [15] updated with the requirements from this annex.
B.1.1 Profile Requirement List (Profile RL)
The profile requirement list (profile RL) for the NWK, DLC, MAC and PHL layers as defined in this annex is
based on ETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14] and [15]. For every capability listed in
ETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14] and [15], the profile requirements are expressed by
restriction upon allowed support answers in ETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14] and [15]. The
Profile RL is produced by copying selected tables from ETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14]
and [15], removing the column(s) to be completed by the supplier, and adding a new set of columns giving
the new profile requirements, both in terms of the status and allowed values. The tables are referenced by
preceding it with the relevant reference standard.
Profile status column
The standardized symbols for the status column are as follows:
m or M mandatory - the capability is required to be supported;
o or O optional - the capability may be supported or not;
n/a or N/A not applicable - in the given context, it is impossible to use the capability;
x or X prohibited (excluded) - there is a requirement not to use this capability in the
given context;
o.i or O.i qualified optional - for mutually exclusive or selectable options from a set. "i" is
an integer which identifies an unique group of related optional items and the logic
of their selection which is defined immediately following the table;
ci or Ci conditional - the requirement on the capability ("m", "o", "x" or "n/a") depends on
the support of other optional or conditional items. "i" is an integer identifying an
unique conditional status expression which is defined immediately following the
table or which is defined in the general condition table below;
i or I out-of-scope - this capability is outside the scope of the given specification, and
hence irrelevant and not subject to conformance testing. This status is in
particular applicable for data fields which are reserved for future use. The
structure of such fields has to be supported, but the value is undefined and thus
to be ignored.
Reference column
The reference column gives reference to ETS 300 434-1 [10] or ETS 300 434-2 [11] stated by using the
reference standard preceding the number of the subclause, except where explicitly stated otherwise.
Page 19
ETS 300 705-2: June 1997
B.1.2 General conditions
Table B.1: General condition table
Condition identifier Condition definition
note 1 The status of the relevant item is exactly as the status of this item in
ETS 300 476 Parts 4, 5, 6 and 7 [12], [13], [14] and [15]. The item has been
included as the Profile reference column include reference to the profile that
describes the item more in details.
B.2 Requirement lists on DECT protocols
B.2.1 Requirement list on DECT NWK layer
B.2.1.1 Network entities
To express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following table
indicates the change of status for support of entities.
Table B.2: ETS 300 476-4 [12], Table A.12 Entity
Item Entity name Profile Reference Profile Status
1 Call control (CC) ETS 300 434-1 [10], m
subclause 5.2.4.1
2 Call Independent Supplementary Services (CISS) ETS 300 434-1 [10], o
subclause 5.2.4.1
6 Link control entity (LCE) ETS 300 434-2 [11], m
subclause 5.2
B.2.1.2 Network features
B.2.1.2.1 CC features
To express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following table
indicates the change of status for support of features.
Page 20
ETS 300 705-2: June 1997
Table B.3: ETS 300 476-4 [12], Table A.13 CC features
Item Feature name Profile Reference Profile Status
3 Control of supervisory tones ETS 300 434-2 [11], o
subclause 4.1.9
5 Dialled digits (basic) ETS 300 434-2 [11], m
subclause 4.1.5
6 Dialled digits additional ETS 300 434-2 [11], o
subclause 4.1.6
7 Dialling delimiter ETS 300 434-2 [11], o
subclause 4.1.7
17 Incoming call ETS 300 434-2 [11], m
subclause 4.1.8
19 Off hook ETS 300 434-2 [11], m
subclause 4.1.3
20 On hook (full release) ETS 300 434-2 [11], m
subclause 4.1.4
21 Outgoing call ETS 300 434-2 [11], m
subclause 4.1.1
26 Signalling of display characters ETS 300 434-2 [11], o
subclause 4.1.10
27 Selection of bearer service ETS 300 434-2 [11], m
subclause 4.1.12
B.2.1.2.2 SS features (services)
To express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following table
indicates the change of status for support of supplementary services.
Page 21
ETS 300 705-2: June 1997
Table B.4: ETS 300 476-4 [12], Table A.15 SS features (services)
Item Feature name Profile Reference Profile Status
1 Advice of Charge (AOC) ETS 300 434-2 [11], o
subclause 4.1.27
3 Call Deflection (CD) ETS 300 434-2 [11], o
subclause 4.1.31
4 Call Forwarding Busy (CFB) ETS 300 434-2 [11], o
subclause 4.1.39
5 Call Forwarding No Reply (CFNR) ETS 300 434-2 [11], o
subclause 4.1.39
6 Call Forwarding Unconditional (CFU) ETS 300 434-2 [11], o
subclause 4.1.39
7 Call Waiting (CW) ETS 300 434-2 [11], o
subclause 4.1.24
8 Calling Line Identification Presentation (CLIP) ETS 300 434-2 [11], o
subclause 4.1.17
9 Calling Line Identification Restriction (CLIR) ETS 300 434-2 [11], o
subclause 4.1.18
10 Closed User Group (CUG) ETS 300 434-2 [11], o
subclause 4.1.26
11 Completion of Calls to Busy Subscriber (CCBS) ETS 300 434-2 [11], o
subclause 4.1.36
12 Call Hold(CH) ETS 300 434-2 [11], o
subclause 4.1.25
13 Conference call, add-on (CONF) ETS 300 434-2 [11], o
subclause 4.1.29
14 Connected Line identification Presentation (COLP) ETS 300 434-2 [11], o
subclause 4.1.19
15 Connected Line identification Restriction (COLR) ETS 300 434-2 [11], o
subclause 4.1.20
21 Direct Dialling In (DDI) ETS 300 434-2 [11], o
subclause 4.1.22
22 Explicit Call Transfer (ECT) ETS 300 434-2 [11], o
subclause 4.1.35
24 Freephone (FPH) ETS 300 434-2 [11], o
subclause 4.1.37
26 Hold call (PT to FT) ETS 300 434-2 [11], o
subclause 4.1.14
29 Malicious Call Identification (MCID) ETS 300 434-2 [11], o
subclause 4.1.28
30 Multiple Subscriber Number (MSN) ETS 300 434-2 [11], o
subclause 4.1.21
34 Re-connection of held call (PT to FT) ETS 300 434-2 [11], o
subclause 4.1.39
36 Selection of required teleservice ETS 300 434-2 [11], o
subclause 4.1.11
39 Subaddressing (SUB) ETS 300 434-2 [11], o
subclause 4.1.23
40 Terminal Portability (TP) ETS 300 434-1 [10], i
subclause 5.2.2.5.8
41 Three-Party (3PTY) ETS 300 434-2 [11], o
subclause 4.1.30
42 User to User Signalling (UUS) ETS 300 434-2 [11], o
subclauses 4.1.32, 4.1.33,
4.1.34
Page 22
ETS 300 705-2: June 1997
B.2.1.2.3 LCE features
To express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following table
indicates the change of status for support of LCE features.
Table B.5: ETS 300 476-4 [12], Table A.16 LCE features
Item Feature name Profile Reference Profile Status
1 Connection oriented Link control (Link control) ETS 300 434-2 [11], m
subclause 5.2
B.2.1.3 Procedures
To express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following table
indicates the change of status for support of the procedures.
Table B.6: ETS 300 476-4 [12], Table A.18 CC procedures
Item Procedure name Profile Reference Profile Status
1 cc_outgoing_normal_call_request ETS 300 434-2 [11], m
subclause 5.2
5 cc_outgoing_connection_of_U_plane ETS 300 434-2 [11], m
subclause 5.2
6 cc_outgoing_overlap_sending ETS 300 434-2 [11], m
subclause 5.2
7 cc_outgoing_call_proceeding ETS 300 434-2 [11], m
subclause 5.2
8 cc_outgoing_call_confirmation ETS 300 434-2 [11], m
subclause 5.2
9 cc_outgoing_call_connection ETS 300 434-2 [11], m
subclause 5.2
12 cc_incoming_connection_of_U_plane ETS 300 434-2 [11], m
subclause 5.2
15 cc_incoming_call_confirmation ETS 300 434-2 [11], m
subclause 5.2
16 cc_incoming_call_connection ETS 300 434-2 [11], m
subclause 5.2
17 cc_sending_terminal_capability ETS 300 434-2 [11], m
subclause 5.2
19 cc_call_information ETS 300 434-2 [11], o
subclause 5.2
20 cc_normal_call_release ETS 300 434-2 [11], m
subclause 5.2
22 cc_abnormal_call_release ETS 300 434-2 [11], m
subclause 5.2
23 cc_release_collisions ETS 300 434-2 [11], m
subclause 5.2
32 cc_timer_f_cc_03_mgt ETS 300 434-2 [11], m
subclause 5.2
33 cc_timer_f_cc_04_mgt ETS 300 434-2 [11], see table B.1
subclause 5.2
Page 23
ETS 300 705-2: June 1997
Table B.7: ETS 300 476-4 [12], Table A.20 SS protocols
Item SS protocol name Profile Reference Profile Status
1 crss_keypad_protocol ETS 300 434-1 [10], subclause o
5.2.2.1
3 crss_functional_protocol_smc ETS 300 434-1 [10], subclause o
5.2.2.3
4 ciss_keypad_protocol ETS 300 434-1 [10], subclause i
5.2.2.2
7 crss_functional_protocol_ciec ETS 300 434-1 [10], subclause o
5.2.2.3
8 ciss_functional_protocol_ciec ETS 300 434-1 [10], subclause o
5.2.2.4.1
Table B.8: ETS 300 476-4 [12], Table A.23 LCE procedures
Item Procedure name Profile Reference Profile Status
1 lce_direct_pt_init_link_establishment ETS 300 434-2 [11], m
subclause 5.2
2 lce_indirect_ft_init_link_establishment ETS 300 434-2 [11], m
subclause 5.2
3 lce_direct_ft_init_link_establishment ETS 300 434-2 [11], o
subclause 5.2
4 lce_link_maintenance ETS 300 434-2 [11], m
subclause 5.2
7 lce_link_release ETS 300 434-2 [11], m
subclause 5.2
11 lce_timer_lce_01_mgt ETS 300 434-2 [11], m
subclause 5.2
12 lce_timer_lce_02_mgt ETS 300 434-2 [11], m
subclause 5.2
13 lce_timer_lce_03_mgt ETS 300 434-2 [11], m
subclause 5.2
Page 24
ETS 300 705-2: June 1997
B.2.1.4 Messages
To express the profile requirements of ETS 300 434-1 [10] and ETS 300 434-2 [11], the following tables
indicate the change of status for support of messages.
B.2.1.4.1 CC messages
Table B.9: ETS 300 476-4 [12], Table A.25 CC receiving (P to F) messages
Item CC receiving (P to F) Profile Reference Profile Status
Message name
1 CC-SETUP ETS 300 434-1 [10], m
subclause 5.2.4.2
2 CC-INFOrmation ETS 300 434-1 [10], m
subclause 5.2.4.2
5 CC-ALERTING ETS 300 434-1 [10], m
subclause 5.2.4.2
6 CC-CONNECT ETS 300 434-1 [10], m
subclause 5.2.4.2
8 CC-RELEASE ETS 300 434-1 [10], m
subclause 5.2.4.2
9 CC-RELEASE-COMplete ETS 300 434-1 [10], m
subclause 5.2.4.2
14 IWU-INFOrmation ETS 300 434-1 [10], i
subclause 5.2.4.2
Table B.10: ETS 300 476-4 [12], Table A.26 CC sending (F to P) messages
Item CC sending (F to P) Profile Reference Profile Status
Message name
1 CC-SETUP ETS 300 434-1 [10], m
subclause 5.2.4.1
2 CC-INFOrmation ETS 300 434-1 [10], m
subclause 5.2.4.1
3 CC-SETUP-ACKnowledge ETS 300 434-1 [10], m
subclause 5.2.4.1
4 CC-CALL-PROCeeding ETS 300 434-1 [10], m
subclause 5.2.4.1
5 CC-ALERTING ETS 300 434-1 [10], m
subclause 5.2.4.1
6 CC-CONNECT ETS 300 434-1 [10], m
subclause 5.2.4.1
7 CC-CONNECT-ACKnowledge ETS 300 434-1 [10], m
subclause 5.2.4.1
8 CC-RELEASE ETS 300 434-1 [10], m
subclause 5.2.4.1
9 CC-RELEASE-COMplete ETS 300 434-1 [10], m
subclause 5.2.4.1
Page 25
ETS 300 705-2: June 1997
B.2.1.4.2 CRSS and CISS messages
Table B.11: ETS 300 476-4 [12], Table A.86 CRSS & CISS messages receiving (P to F)
Item CRSS & CISS messages receiving (P to F) Profile Reference Profile Status
Message name
1 FACILITY ETS 300 434-2 [11], o
subclause 5.2.4.2
2 HOLD ETS 300 434-2 [11], c1101
subclause 5.2.4.2
5 RETRIEVE ETS 300 434-2 [11], c1101
subclause 5.2.4.2
8 CISS-REGISTER ETS 300 434-2 [11], o
subclause 5.2.4.2
9 CISS-RELEASE-COMplete ETS 300 434-2 [11], o
subclause 5.2.4.2
c1101: IF ETS 300 476-4 [12] Table A.15/12 THEN m ELSE o
Table B.12: ETS 300 476-4 [12], Table A.87 CRSS & CISS messages sending (F to P)
Item CRSS & CISS messages sending (F to P) Profile Reference Profile Status
Message name
1 FACILITY ETS 300 434-2 [11], o
subclause 5.2.4.1
3 HOLD-ACKnowledge ETS 300 434-2 [11], c1201
subclause 5.2.4.1
4 HOLD-REJECT ETS 300 434-2 [11], c1201
subclause 5.2.4.1
6 RETRIEVE-ACKnowledge ETS 300 434-2 [11], c1201
subclause 5.2.4.1
7 RETRIEVE-REJECT ETS 300 434-2 [11], c1201
subclause 5.2.4.1
8 CISS-REGISTER ETS 300 434-2 [11], o
subclause 5.2.4.1
9 CISS-RELEASE-COMplete ETS 300 434-2 [11], o
subclause 5.2.4.1
c1201: IF ETS 300 476-4 [12] Table A.15/12 THEN m ELSE o
B.2.1.4.3 LCE messages
Table B.13: ETS 300 476-4 [12], Table A.126 LCE message receiving (P to F)
Item LCE message receiving (P to F) Profile Reference Profile Status
1 LCE-PAGE-RESPONSE ETS 300 434-1 [10], figure 22 m
Table B.14: ETS 300 476-4 [12], Table A.127 LCE message sending (F to P)
Item LCE message sending (F to P) Profile Reference Profile Status
2 LCE-PAGE-REJECT ETS 300 434-1 [10], figure 22 m
3 LCE-REQUEST-PAGE short ETS 300 434-1 [10], figure 22 m
4 LCE-REQUEST-PAGE long ETS 300 434-1 [10], figure 22 m
-----
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...