SIST EN 12697-17:2004
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 17: Particle loss of porous asphalt specimen
Bituminous mixtures - Test methods for hot mix asphalt - Part 17: Particle loss of porous asphalt specimen
This European Standard describes a test method for determining the particle loss of porous asphalt mixtures. Particle loss is assessed by the loss of mass of porous asphalt samples after turns in the Los Angeles machine. This test enables the estimation of the abrasiveness of porous asphalt. The test applies to laboratory compacted porous asphalt mixtures the upper sieve size of which does not exceed 25 mm. It does not reflect the abrasive effect by studded tyres.
Asphalt - Prüfverfahren für Heißasphalt - Teil 17: Kornverlust von Probekörpern aus offenporigem Asphalt
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 17: Perte de matériau des éprouvettes d'enrobé drainant
Bitumenske zmesi – Preskusne metode za vroče asfaltne zmesi – 17. del: Obraba delcev poroznih asfaltnih preskušancev
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 17: Particle loss of porous asphalt specimenMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 17: Perte de matériau des éprouvettes d'enrobé drainantAsphalt - Prüfverfahren für Heißasphalt - Teil 17: Kornverlust von Probekörpern aus offenporigem AsphaltTa slovenski standard je istoveten z:EN 12697-17:2004SIST EN 12697-17:2004en93.080.20Materiali za gradnjo cestRoad construction materialsICS:SLOVENSKI
STANDARDSIST EN 12697-17:200401-september-2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12697-17June 2004ICS 93.080.20English versionBituminous mixtures - Test methods for hot mix asphalt - Part17: Particle loss of porous asphalt specimenMélanges bitumineux - Méthodes d'essai pour mélangehydrocarboné à chaud - Partie 17: Perte de matériau deséprouvettes d'enrobé drainantAsphalt - Prüfverfahren für Heißasphalt - Teil 17:Kornverlust von Probekörpern aus offenporigem AsphaltThis European Standard was approved by CEN on 1 April 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2004 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12697-17:2004: E
EN 12697-17:2004 (E) 2 Contents page Foreword.3 1 Scope.6 2 Normative references.6 3 Apparatus.6 4 Preparation of test specimen.6 5 Procedure.7 6 Calculation.7 7 Test report.7 8 Precision.8
EN 12697-17:2004 (E) 3 Foreword This document (EN 12697-17:2004) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2004, and conflicting national standards shall be withdrawn at the latest by August 2005. This European Standard is one of a series of standards as listed below: EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content EN 12697-2, Bituminous mixtures — Test method for hot mix asphalt — Part 2: Determination of particle size distribution EN 12697-3, Bituminous mixtures - Test methods for hot mix asphalt - Part 3: Bitumen recovery: Rotary evaporator EN 12697-4, Bituminous mixtures - Test methods for hot mix asphalt - Part 4: Bitumen recovery: Fractionating column EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density EN 12697-6, Bituminous mixtures - Test methods for hot mix asphalt - Part 6: Determination of bulk density of bituminous specimens EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays EN 12697-8, Bituminous mixtures - Test methods for hot mix asphalt - Part 8: Determination of void characteristics of bituminous specimens EN 12697-9, Bituminous mixtures - Test methods for hot mix asphalt - Part 9: Determination of the reference density EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactability EN 12697-11, Bituminous mixtures - Test methods for hot mix asphalt - Part 11: Determination of the affinity between aggregate and bitumen EN 12697-12, Bituminous mixtures - Test methods for hot mix asphalt - Part 12: Determination of the water sensitivity of bituminous specimens EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres
EN 12697-17:2004 (E) 4 EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Particle loss of porous asphalt specimen prEN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen EN 12697-20, Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or Marshall specimens EN 12697-21, Bituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking EN 12697-23, Bituminous mixtures - Test methods for hot mix asphalt - Part 23: Determination of the indirect tensile strength of bituminous specimens EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue prEN 12697-25, Bituminous mixtures - Test methods for hot mix asphalt - Part 25: Cyclic compression test prEN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading EN 12697-29, Bituminous mixtures - Test method for hot mix asphalt - Part 29: Determination of the dimensions of a bituminous specimen EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor EN 12697-32, Bituminous mixtures — Test methods fo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.