SIST EN ISO 9117-1:2009
(Main)Paints and varnishes - Determination of through-dry state and through-dry time - Method of test (ISO 9117-1:2009)
Paints and varnishes - Determination of through-dry state and through-dry time - Method of test (ISO 9117-1:2009)
ISO 9117-1:2009 specifies a test method for determining under standard conditions whether a single coat or a multi-coat system of paint, varnish or related material has reached the through-dry state after a specified drying period.
The test procedure may also be used to determine the time taken to achieve that state.
Beschichtungsstoffe - Bestimmung des Durchtrocknungszustandes und der Durchtrocknungszeit - Prüfverfahren (ISO 9117-1:2009)
Diese Internationale Norm gehört zu einer Reihe von Normen, welche die Probenahme und die Prüfung von Lacken, Anstrichstoffe und ähnlichen Beschichtungsstoffen behandelt. Sie legt ein Prüfverfahren fest, nach dem bestimmt werden kann, ob ein Ein- oder Mehrschichtsystem eines Anstrichstoffes oder eines ähnlichen Beschichtungsstoffes unter Standardbedingungen nach einer festgelegten Trocknungszeit den Durch¬trocknungszustand erreicht hat, d. h. eine ja/nein-Prüfung. Das Prüfverfahren kann auch dazu benutzt werden, die für die Erreichung dieses Zustandes erforderliche Zeit zu bestimmen.
Peintures et vernis - Détermination du séchage à coeur et du temps de séchage à coeur - Méthode d'essai (ISO 9117-1:2009)
L'ISO 9117‑1:2009 spécifie une méthode d'essai permettant de déterminer, dans des conditions normalisées, si un système monocouche ou multicouche de peinture, vernis ou produit assimilé a atteint l'état sec à cœur, après un temps de séchage spécifié.
Il est également possible d'utiliser cette méthode d'essai pour déterminer le temps nécessaire pour atteindre cet état.
Barve in laki - Določanje utrjenega stanja in časa utrjevanja - Preskusna metoda (ISO 9117-1:2009)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2009
1DGRPHãþD
SIST EN 29117:1997
%DUYHLQODNL'RORþDQMHXWUMHQHJDVWDQMDLQþDVDXWUMHYDQMD3UHVNXVQDPHWRGD
,62
Paints and varnishes - Determination of through-dry state and through-dry time - Method
of test (ISO 9117-1:2009)
Beschichtungsstoffe - Bestimmung des Durchtrocknungszustandes und der
Durchtrocknungszeit - Prüfverfahren (ISO 9117-1:2009)
Peintures et vernis - Détermination du séchage à coeur et du temps de séchage à coeur
- Méthode d'essai (ISO 9117-1:2009)
Ta slovenski standard je istoveten z: EN ISO 9117-1:2009
ICS:
87.040 Barve in laki Paints and varnishes
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 9117-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2009
ICS 87.040 Supersedes EN 29117:1992
English Version
Paints and varnishes - Drying tests - Part 1: Determination of
through-dry state and through-dry time (ISO 9117-1:2009)
Peintures et vernis - Essais de séchage - Partie 1: Beschichtungsstoffe - Trocknungsprüfungen - Teil 1:
Détermination du séchage à coeur et du temps de séchage Bestimmung des Durchtrocknungszustandes und der
à coeur (ISO 9117-1:2009) Durchtrocknungszeit (ISO 9117-1:2009)
This European Standard was approved by CEN on 23 April 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 9117-1:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 9117-1:2009) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn
at the latest by November 2009.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 29117:1992.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 9117-1:2009 has been approved by CEN as a EN ISO 9117-1:2009 without any modification.
INTERNATIONAL ISO
STANDARD 9117-1
First edition
2009-05-15
Paints and varnishes — Drying tests —
Part 1:
Determination of through-dry state
and through-dry time
Peintures et vernis — Essais de séchage —
Partie 1: Détermination du séchage à cœur et du temps de séchage
à cœur
Reference number
ISO 9117-1:2009(E)
©
ISO 2009
ISO 9117-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
ISO 9117-1:2009(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Terms, definitions and abbreviated terms . 1
4 Principle. 2
5 Apparatus and materials. 2
6 Sampling. 4
7 Test panels . 4
7.1 Substrate . 4
7.2 Preparation and coating. 4
8 Procedure . 5
8.1 Preparation of apparatus . 5
8.2 Drying the test panel . 5
8.3 Determination of through-dry state . 5
8.4 Determination of through-dry time . 5
8.5 Thickness of coating . 6
9 Precision. 6
10 Test report . 6
Bibliography . 7
ISO 9117-1:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 9117-1 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 9,
General test methods for paints and varnishes, in collaboration with CEN/TC 139, Paints and varnishes.
It cancels and replaces ISO 9117:1990, which has been technically revised. The main changes are:
a) failure is defined in terms of damage, rather than damage or marking;
b) the former Annex A concerning required supplementary information has been integrated in the test report.
ISO 9117 consists of the following parts, under the general title Paints and varnishes — Drying tests:
⎯ Part 1: Determination of through-dry state and through-dry time
1)
⎯ Part 2: Pressure test for stackability
2)
⎯ Part 3: Surface-drying test using ballotini
1) To be published. (Revision of ISO 4622:1992)
2) To be published. (Revision of ISO 1517:1973)
iv © ISO 2009 – All rights reserved
INTERNATIONAL STANDARD ISO 9117-1:2009(E)
Paints and varnishes — Drying tests —
Part 1:
Determination of through-dry state and through-dry time
1 Scope
This part of ISO 9117 specifies a test method for determining under standard conditions whether a single coat
or a multi-coat system of paint, varnish or related material has reached the through-dry state after a specified
drying period.
NOTE The test procedure may also be used to determine the time taken to achieve that state.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 48, Rubber, vulcanized or thermoplastic — Determination of hardness (hardness between 10 IRHD and
100 IRHD)
ISO 1513, Paints and varnishes — Preparation of test samples
ISO 1514, Paints and varnishes — Standard panels for testing
ISO 2808, Paints and varnishes — Determination of film thickness
ISO 15528, Paints, varnishes and raw materials for paints and varnishes — Sampling
3 Terms, definitions and abbreviated terms
For the purposes of this document, the following terms, definitions and abbreviated terms apply.
3.1
IRHD scale
international rubber hardness degree scale
3.2
through-dry state
condition of a film in which it is dry throughout its thickness
NOTE 1 The through-dry state should not be confused with the condition in which the surface of the film is dry but the
bulk of the coating is still mobile.
ISO 9117-1:2009(E)
NOTE 2 For the purposes of this part of ISO 9117, a single coating or a multi-coat system of paint or varnish or related
material is considered to be through-dry when a specified gauze under specified pressure, torsion and time does not
damage the film.
3.3
through-dry time
period of time between the application of a coat to a prepared test panel and the achievement of the through-
dry state, as determined by the specified test procedure
4 Principle
A coat of paint or varnish of agreed thickness is applied to a substrate and is allowed to dry under specified
conditions. The completeness of drying throughout the coat is determined by examination of the surface of the
coat after the application of a load, applied over a given area of the surface, and subsequent rotation of the
load-applying face through 90°.
5 Apparatus and materials
Ordinary laboratory apparatus and glassware together with the following:
5.1 Baseplate and plunger assembly (see Figure 1 and Figure 2), consisting essentially of a baseplate
and a free-sliding pl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.