SIST EN 140401-804:2005

Detail specification: Fixed low power non wire-wound high stability surface mount (SMD) resistors - Rectangular - Stability classes 0,1; 0,25

Superseded by EN 140401-804:2011

Bauartspezifikation: Oberflächenmontierbare nichtdrahtgewickelte Festwiderstände (SMD) niedriger Belastbarkeit mit hoher Stabilität - Rechteckig - Stabilitätsklassen 0,1; 0,25

Spécification particulière: Résistances fixes non bobinées à faible dissipation pour montage en surface (CMS) - Rectangulaire - Catégories de stabilité 0,1; 0,25

Podrobna specifikacija: pritrjeni, majhnih moči, nežični, zelo stabilni upori za površinsko namestitev (SMD) – Pravokotni – Razreda stabilnosti 0,1 in 0,25

General Information

• Status: Withdrawn
• Publication Date: 30-Nov-2005
• Withdrawal Date: 22-Jul-2018
• ICS: 31.040.10 - Fixed resistors
• Technical Committee: SS EIT - Technical Board for the electrotechnical, information technology and telecommunications fields
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 23-Jul-2018
• Due Date: 15-Aug-2018
• Completion Date: 23-Jul-2018
• Ref Project: EN 140401-804:2005 - Detail specification: Fixed low power non wire-wound high stability surface mount (SMD) resistors - Rectangular - Stability classes 0,1; 0,25

Relations

• Replaced By: SIST EN 140401-804:2011 - Detail Specification: Fixed low power film high stability SMD resistors - Rectangular - Stability classes 0,1; 0,25
• Effective Date: 28-Jan-2023
• Replaced By: SIST EN 140401-804:2011 - Detail Specification: Fixed low power film high stability SMD resistors - Rectangular - Stability classes 0,1; 0,25
• Effective Date: 01-Dec-2011

Standards Content (Sample)

SIST EN 140401-804:2005SLOVENSKIdecember 2005
STANDARDPodrobna specifikacija: pritrjeni, majhnih moči, nežični, zelo stabilni upori za površinsko namestitev (SMD) – Pravokotni – Razreda stabilnosti 0,1 in 0,25Detail specification: Fixed low power non wire-wound high stability surface mount (SMD) resistors – Rectangular – Stability classes 0,1; 0,25©
Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljenoReferenčna številkaSIST EN 140401-804:2005(en)ICS31.040.10







EUROPEAN STANDARD
EN 140401-804 NORME EUROPÉENNE EUROPÄISCHE NORM
March 2005 CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 140401-804:2005 E
ICS 31.040.10
English version
Detail specification: Fixed low power non wire-wound high stability surface mount (SMD) resistors –
Rectangular –
Stability classes 0,1; 0,25
Spécification particulière:
Résistances fixes non bobinées
à faible dissipation pour montage
en surface (CMS) –
Rectangulaire –
Catégories de stabilité 0,1; 0,25
Bauartspezifikation: Oberflächenmontierbare nichtdrahtgewickelte Festwiderstände (SMD) niedriger Belastbarkeit
mit hoher Stabilität –
Rechteckig –
Stabilitätsklassen 0,1; 0,25
This European Standard was approved by CENELEC on 2004-10-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.



EN 140401-804:2005 – 2 –
Foreword
This European Standard was prepared by the Technical Committee CENELEC TC 40XB, Resistors.
The text of the draft was submitted to the Unique Acceptance Procedure and was approved by CENELEC as EN 140401-804 on 2004-11-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2005-10-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2007-10-01 This specification is part of 4 documents describing fixed resistors for surface mount technology as follows:
EN 60115-1 Fixed resistors for use in electronic equipment – Part 1: Generic specification (IEC 60115-1, mod.) EN 140400 Sectional specification: Fixed low power surface mount (SMD) resistors EN 140401 Blank Detail Specification: Fixed low power non wire-wound surface mount (SMD) resistors EN 140401-804 Detail specification: Fixed low power non-wirewound high stability surface mount (SMD) resistors – Rectangular – Stability classes 0,1; 0,25 __________



– 3 – EN 140401-804:2005
Contents
1 Characteristics and ratings.4 1.1 Dimensions and Ratings.4 1.2 Derating curve.5 1.3 Resistance range and tolerance on rated resistance.6 1.4 Variation of resistance with temperature and temperature rise.8 1.5 Climatic categories.8 1.6 Limits for change of resistance at tests.8 1.7 Non-linear properties.9 1.8 Marking, packaging and ordering designation.10 1.8.1 Component.10 1.8.2 Package.10 1.8.3 Packaging / Taping.10 1.8.4 Ordering information.10 1.9 Additional information (not for inspection purpose).11 1.9.1 Storage.11 1.9.2 Mounting.11 1.9.3 Soldering process.11 1.9.4 Conductive gluing.11 1.9.5 Use of cleaning solvents.11 1.9.6 Pulse load capability.12 1.9.7 Variation of resistance value (drift) for lifetimes up to 200 000 h.15 1.9.8 Dissipation notes.16 1.9.9 Current noise.16 2 Quality assessment procedures.17 2.1 General.17 2.1.1 Zero defect approach.17 2.1.2 100 %-Test.17 2.1.3 0 Ω -Resistor.17 2.1.4 Certificate of Conformity (CoC).17 2.1.5 Certified test records.17 2.1.6 Failure rate level (only version E).17 2.2 Qualification Approval.18 2.2.1 Version A.18 2.2.2 Version E.18 2.3 Quality conformance inspection.18 2.3.1 Qualification approval according to EN 100114-2.18 2.3.2 Technology approval according to EN 100114-6.18 2.3.3 Non-conforming items.18 Annex A (normative) Fixed sample size Qualification Approval and Quality Conformance Inspection test schedule for fixed low power surface mount (SMD) resistors.19 Annex B (informative)
Letter symbols and abbreviations.23 Annex C (normative)
Standards referred to in this specification.24



EN 140401-804:2005 – 4 –
Specification available from
the National Committees members of CENELEC EN 140401-804
Electronic components of assessed quality in accordance with: EN 60115-1:2001 EN 140400:2003 EN 140401:2002 Issue 1
Other shapes are permitted within the given dimensions.
Figure 1 – Outline and dimensions (see Table 1) Fixed low power non wire-wound high stability surface mount (SMD) resistors with rectangular base without leads Style: RR Ceramic substrate with protected, insulated, resistance film and solder terminations, typically thin film Assessment level EZa Version A: with 100 %-test Version E: with failure rate level
and 100 %-test Stability classes 0,1 and 0,25 a For explanations on assessment level EZ see 2.1.1. 1 Characteristics and ratings Various parameters of this component are precisely specified in this specification. Unspecified parameters may vary from one component to another. 1.1 Dimensions and ratings Table 1 – Style and dimensions Style Length L mm Width W mm Height H mm Termination T mm Weighta mg metric inch min. max. min. max. min. max. min. max. max. RR 1005M RR 0402 0,95 1,10 0,45 0,60 0,25 0,40 0,05/0,1b 0,35 0,8 RR 1608M RR 0603 1,50 1,70 0,75 0,95 0,35 0,55 0,10 0,50 2,1 RR 2012M RR 0805 1,85 2,15 1,10 1,40 0,35 0,65 0,15 0,60 6,0 RR 3216M RR 1206 2,90 3,35 1,45 1,75 0,35 0,65 0,25 0,75 10,0 RR 5025M RR 2010 4,80 5,20 2,30 2,70 0,35 0,75 0,35 0,85 30,0 a For information only. b First figure indicates the termination width on the film side, second figure on the reverse side. Termination:
WT ≥ 0,75 · W
Thickness: 0,005 to 0,05 mm Table 2a – Ratings for stability class 0,25 Style Stability class Rated dissipation P70 mW Limiting element voltage d.c. or a.c. (r.m.s) Umax V Insulation voltage d.c. or a.c. (peak) Uins V
1 min continuous RR 1005M 0,25 63 50 75 75 RR 1608M 0,25 100 75 100 75 RR 2012M 0,25 125 150 200 75 RR 3216M 0,25 250 200 300 75 RR 5025M 0,25 330 300 300 75



– 5 – EN 140401-804:2005
Table 2b – Ratings for stability class 0,1 Style Stability class Rated dissipation P70 mW Limiting element voltage d.c. or a.c. (r.m.s) Umax V Insulation voltage d.c. or a.c. (peak) Uins V
1 min continuous RR 1005M 0,1 50 25 75 75 RR 1608M 0,1 75 50 100 75 RR 2012M 0,1 100 75 200 75 RR 3216M 0,1 125 150 300 75 RR 5025M 0,1 250 200 300 75 Table 2c – Ratings for 0 Ω resistors Maximum current Imax A Maximum resistance valueaRmax mΩ Insulation voltage d.c. or a.c. (peak) Uins V Style
1 min continuous RR 1005M
0,63 20 75 75 RR 1608M 1 20 100 75 RR 2012M 1,5 20 200 75 RR 3216M 2,0 20 300 75 RR 5025M 3,0 20 300 75 a The resistance value shall be measured on the film side. 1.2 Derating curve Resistors covered by this specification are derated according to the following diagram:
-50°C 0°C50°C70°C100°C0% 25% 50% 75% 100% Upper category temperature (UCT) Lower category temperature (LCT) +155°C -55°CPercentage of rated dissipation Ambient Temperature ϑ aStability Classes
0,1 & 0,25
Figure 2 – Derating curve For the category temperatures of stability classes refer to Table 6.



EN 140401-804:2005 – 6 –
1.3 Resistance range and tolerance on rated resistance Version A: The following combinations of temperature coefficient, tolerance on rated resistance shall be used for qualification approval according to 2.2.1 and quality conformance inspection according to 2.3. Resistance values of E-series according to IEC 60063 shall be used.
The qualification of resistance values below or beyond the specified resistance values is permitted, if they fulfil the require-ments of the closest stability class (e.g. RR 1608M 1 % > 260 kΩ shall fulfil the requirements of stability class 0,1 or 0,25). Table 3a – Resistance range, tolerance on rated resistance for version A Style Tolerance on rated resistance Temperature coefficient Resistance range Stability class
% Codea ppm/K
RR 1005M ± 1 F ± 25 100 Ω to 49,9 kΩ 0,1
100 Ω to 49,9 kΩ 0,25
± 0,5 D ± 10; ± 25 100 Ω to 49,9 kΩ 0,1
100 Ω to 49,9 kΩ 0,25
± 0,1 B ± 10 100 Ω to 49,9 kΩ 0,1
100 Ω to 49,9 kΩ 0,25 RR 1608M ± 1 F ± 25 100 Ω to 261 kΩ 0,1
100 Ω to 261 kΩ 0,25
± 0,5 D ± 10; ± 25 100 Ω to 261 kΩ 0,1
100 Ω to 261 kΩ 0,25
± 0,1 B ± 10 100 Ω to 261 kΩ 0,1
100 Ω to 261 kΩ 0,25 RR 2012M ± 1 F ± 25 100 Ω to 301 kΩ 0,1
100 Ω to 301 kΩ 0,25
± 0,5 D ± 10; ± 25 100 Ω to 301 kΩ 0,1
100 Ω to 301 kΩ 0,25
± 0,1 B ± 10 100 Ω to 301 kΩ 0,1
100 Ω to 301 kΩ 0,25 RR 3216M ± 1 F ± 25 100 Ω to 1 MΩ 0,1
100 Ω to 1 MΩ 0,25
± 0,5 D ± 10; ± 25 100 Ω to 1 MΩ 0,1
100 Ω to 1 MΩ 0,25
± 0,1 B ± 10 100 Ω to 1 MΩ 0,1
100 Ω to 1 MΩ 0,25 RR 5025M ± 1 F ± 25 100 Ω to 3,01 MΩ 0,1
100 Ω to 3,01 MΩ 0,25
± 0,5 D ± 10; ± 25 100 Ω to 3,01 MΩ 0,1
100 Ω to 3,01 MΩ 0,25
± 0,1 B ± 10 100 Ω to 3,01 MΩ 0,1
100 Ω to 3,01 MΩ 0,25 0 Ω-resistors according to Table 2c for all styles. a Code letters according to EN 60062.



– 7 – EN 140401-804:2005
Version E: The following combinations of temperature coefficient, tolerance on rated resistance and E-series according to IEC 60063 shall be used for qualification approval according to 2.2.2 and quality conformance inspection according to 2.3 and are permitted only: Table 3b – Resistance range, tolerance on rated resistance for version E Style Tolerance on rated resistance Temperature coefficient Resistance range Stability class E series
% Codea ppm/K
RR 1005M ± 1 F ± 25 100 Ω to 49,9 kΩ 0,1
100 Ω to 49,9 kΩ 0,25 E96
± 0,1 B ± 10 100 Ω to 49,9 kΩ 0,1
100 Ω to 49,9 kΩ 0,25 E192 RR 1608M ± 1 F ± 25 100 Ω to 261 kΩ 0,1
100 Ω to 261 kΩ 0,25 E96
± 0,1 B ± 10 100 Ω to 261 kΩ 0,1
100 Ω to 261 kΩ 0,25 E192 RR 2012M ± 1 F ± 25 100 Ω to 30 1kΩ 0,1
100 Ω to 301 kΩ 0,25 E96
± 0,1 B ± 10 100 Ω to 301 kΩ 0,1
100 Ω to 301 kΩ 0,25 E192 RR 3216M ± 1 F ± 25 100 Ω to 1 MΩ 0,1
100 Ω to 1 MΩ 0,25 E96
± 0,1 B ± 10 100 Ω to 1 MΩ 0,1
100 Ω to 1 MΩ 0,25 E192 RR 5025M ± 1 F ± 25 100 Ω to 3,01 MΩ 0,1
100 Ω to 3,01 MΩ 0,25 E96
± 0,1 B ± 10 100 Ω to 3,01 MΩ 0,1
100 Ω to 3,01 MΩ 0,25 E192 0 Ω-resistors according to Table 2c for all styles. a Code letters according to EN 60062.



EN 140401-804:2005 – 8 –
1.4 Variation of resistance with temperature and temperature rise Table 4 – Temperature coefficients and percentage change of resistance (acc. to EN 140400, Table 2) Temperature coefficient Limit of resistance change ∆R/R (%)
Stability classes 0,1 ; 0,25 ppm/K Codea Temp. charact. 20 °C / 70 °C LCT / Ref. temp. -55 °C / 20 °C Ref. temp. / UCT 20 °C / 155 °C ± 25 D ± 0,125 ± 0,188 ± 0,338 ± 10 F ± 0,050 ± 0,075 ± 0,135 a Code letter according to EN 140400, Table 2. Table 5 – Limit of temperature rise Stability class Limit of temperature rise at rated dissipation 0,1 ; 0,25 Tr ≤ 85 K
The thermal resistance is calculated to Rth = Tr / P70. 1.5 Climatic categories Table 6 – Climatic categories Stability class Climatic category LCT / UCT / Duration 0,1 ; 0,25 55 / 155 / 56 1.6 Limits for change of resistance at tests Table 7 – Limits for change of resistance at tests
Stability class Limit of resistance change ∆R/R
EN 60115-1, 4.23 Climatic sequence 4.24 Damp heat, steady state 4.25.3 Endurance at upper category temperature EN 60115-1, 4.25.1 Endurance at 70 °C EN 60115-1, 4.13 Overload 4.18 Resistance to soldering heat 4.19 Rapid change of temperature 4.22 Vibration
1 000 h Extended, 8 000 h 4.33 Substrate bending test 0,25 ± (0,25 % R + 0,05 Ω) ± (0,25 % R + 0,05 Ω) ± (0,5 % R + 0,05 Ω) ± (0,05 % R + 0,01 Ω) 0,1 ± (0,1 % R + 0,02 Ω)
± (0,1 % R + 0,02 Ω)
± (0,25 % R + 0,02 Ω) ± (0,05 % R + 0,01 Ω) a Tightening of the general definition of stability classes against the requirements of EN 140400, 2.1.4.



– 9 – EN 140401-804:2005
1.7 Non-linear properties (for resistance values ≥ 10 Ω)
If measurement of non-linearity is required according to 2.1.2, measured values shall be above the limits given in the diagram below. The resistors shall be tested according to IEC/TR 60440 where the test voltage shall be the rated voltage.
10 Ω 100 Ω 1k Ω 10k Ω 100k Ω 1M Ω0dB 20dB 40dB 60dB 80dB 100dB 120dB RR 3216M & RR 5025M RR 2012M RR 1608M RR 1005M Attenuation of 3rd Harmonic
A3
Resistance Value
Figure 3 – Limits of non-linearity in resistors



EN 140401-804:2005 – 10 –
1.8 Marking, packaging and ordering designation 1.8.1 Component Surface mount resistors are generally not marked on the body. However, if some marking is applied to the body, the resistor shall be marked with the rated resistance according to EN 60062, Clause 3 or with the code letter according to Table 8 and as many of the remaining items listed in 2.4.1 of EN 60115-1 (only version A). For version E the component shall be marked according to EN 60062, Clause 3 or with the code letter according to Table 8. The marking of the style RR 1005M and RR 1608M is not required. Table 8 – Letter coding Resistance range of the series E 96 Code letter
1 Ω to 9,76 Ω1R00 to 9R76
10 Ω to 97,6 Ω10R0 to 97R6 100 Ω to 976 Ω1000 to 9760
1 kΩ to 9,76 kΩ1001 to 9761
10 kΩ to 97,6 kΩ1002 to 9762 100 kΩ to 976 kΩ1003 to 9763
1 MΩ to 9,76 MΩ1004 to 9764 1.8.2 Package The package of the component shall be marked with ordering information in accordance to 1.8.4 with additionally − CECC sign of conformity, − CECC manufacturer code, − NATO manufacturer code (only version E, if required), − date code of manufacture according to EN 60062, additional information is allowed. 1.8.3 Packaging / Taping Components may be taped or put in a bulk case. Taping shall be in accordance with EN 60286-3 type I. Bulk case packaging shall be in accordance with EN 60286-6. For environmental protection packaging into bulk cases is preferred. 1.8.4 Ordering information Orders for resistors covered by this specification shall contain the following information: − detail specification number; − assessment level; − style; − temperature coefficient; − rated resistance; − tolerance on rated resistance; − failure rate level (only Version E); − form of delivery, packing method (in addition to the ordering information given in the examples below). Example of the ordering information for a 150 Ω-resistor: Example of the ordering information for a 0 Ω−resistor: CECC 40 401-804 EZ RR 2012M -
0R00 - E5 Version A: CECC 40401-804 EZ RR 2012M B 150R F E0 Version E (with failure rate level): CECC 40401-804 EZ RR 2012M B 150R F E5 Detail specification number
Assessment level
Style (see Table 1)
Temperature coefficient (see Table 4)
Rated resistance
(coded acc. to EN 60062, 4 characters)
Tolerance on rated resistance
(see Table a, Table b)
Failure rate level
(coded acc. to EN 60115-1, Table ZB1)



– 11 – EN 140401-804:2005
1.9 Additional information (not for inspection purpose) 1.9.1 Storage The solderability and the change of resistance – particularly for precision resistors – may be affected by storage. The conditions of storage are given in EN 60115-1, 2.7. The permitted storage time is 20 years. Solderability testing and measurement of the resistance value before delivery is recommended if storage time exceeds 2 years. 1.9.2 Mounting The resistors are suitable for mounting on all common printed boards, ceramics and flexible foils. 1.9.3 Soldering process The resistors are suitable for all soldering methods according to EN 61760-1. The immersion time shall not be longer than 10 s when immersed in a soldering bath of 260 °C. 1.9.4 Conductive gluing The resistors can be mounted with adhesive suitable for SMD mounting. The required adhesive, the adhesive curing tempera-ture and the curing time has to be agreed between customer and manufacturer. 1.9.5 Use of cleaning solvents It is recommended t
...