SIST EN ISO 11502:2019
(Main)Plastics - Film and sheeting - Determination of blocking resistance (ISO 11502:2018)
Plastics - Film and sheeting - Determination of blocking resistance (ISO 11502:2018)
This document specifies two methods for assessing the tendency of flexible plastic films and sheets to
adhere to one another when left in contact for some time, at a specified temperature and under light
pressure. One method is qualitative and the other is quantitative.
Kunststoffe - Folien und Bahnen - Bestimmung des Blockwiderstandes (ISO 11502:2018)
Dieses Dokument legt zwei Verfahren zur Beurteilung der Neigung von flexiblen Kunststofffolien und Kunststoffbahnen fest, aneinander zu haften, wenn sie sich eine bestimmte Zeit bei einer festgelegten Temperatur und unter leichtem Druck in Kontakt miteinander befunden haben. Das eine Verfahren ist ein qualitatives, das andere ein quantitatives Verfahren.
Plastiques - Film et feuille - Détermination du pouvoir bloquant (ISO 11502:2018)
Le présent document spécifié deux méthodes pour l'évaluation de la tendance de films et feuilles plastiques souples à adhérer les un(e) aux autres lorsqu'ils (elles) sont en contact pendant quelque temps, à une température donnée et sous faible pression. Une méthode est qualitative et l'autre est quantitative.
Polimerni materiali - Filmi in folije - Ugotavljanje odpornosti proti zlepljenju (ISO 11502:2018)
Ta dokument določa dve metodi za ocenjevanje težnje fleksibilnih filmov in folij iz polimernih materialov za zlepljenje, če so nekaj časa v stiku, pri določeni temperaturi in pod manjšim pritiskom. Ena metoda je kakovostna, druga pa količinska.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11502:2019
01-februar-2019
1DGRPHãþD
SIST EN ISO 11502:2005
Polimerni materiali - Filmi in folije - Ugotavljanje odpornosti proti zlepljenju (ISO
11502:2018)
Plastics - Film and sheeting - Determination of blocking resistance (ISO 11502:2018)
Kunststoffe - Folien und Bahnen - Bestimmung des Blockwiderstandes (ISO
11502:2018)
Plastiques - Film et feuille - Détermination du pouvoir bloquant (ISO 11502:2018)
Ta slovenski standard je istoveten z: EN ISO 11502:2018
ICS:
83.140.10 Filmi in folije Films and sheets
SIST EN ISO 11502:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11502:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 11502:2019
EN ISO 11502
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2018
EUROPÄISCHE NORM
ICS 83.140.10 Supersedes EN ISO 11502:2005
English Version
Plastics - Film and sheeting - Determination of blocking
resistance (ISO 11502:2018)
Plastiques - Film et feuille - Détermination du pouvoir Kunststoffe - Folien und Bahnen - Bestimmung des
bloquant (ISO 11502:2018) Blockwiderstandes (ISO 11502:2018)
This European Standard was approved by CEN on 4 November 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11502:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11502:2019
EN ISO 11502:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11502:2019
EN ISO 11502:2018 (E)
European foreword
This document (EN ISO 11502:2018) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2019, and conflicting national standards shall be
withdrawn at the latest by June 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11502:2005.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11502:2018 has been approved by CEN as EN ISO 11502:2018 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11502:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 11502:2019
INTERNATIONAL ISO
STANDARD 11502
Second edition
2018-11
Plastics — Film and sheeting —
Determination of blocking resistance
Plastiques — Film et feuille — Détermination du pouvoir bloquant
Reference number
ISO 11502:2018(E)
©
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 11502:2019
ISO 11502:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11502:2019
ISO 11502:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Method A: Qualitative method . 1
4.1 Principle . 1
4.2 Apparatus . 1
4.3 Test specimens . 2
4.3.1 Shape and dimensions . 2
4.3.2 Preparation . 2
4.4 Procedure . 2
4.5 Test report . 3
5 Method B: Quantitative method . 3
5.1 Principle . 3
5.2 Apparatus . 3
5.3 Test specimens . 3
5.3.1 Shape and dimensions . 3
5.3.2 Preparation . 4
5.4 Procedure . 4
5.5 Precision . 4
5.6 Test report . 5
© ISO 2018 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11502:2019
ISO 11502:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
This second edition cancels and replaces the first edition (ISO 11502:1995), of which it constitutes a
minor revision. The changes compared to the previous edition are as follows:
...
SLOVENSKI STANDARD
oSIST prEN ISO 11502:2018
01-oktober-2018
Polimerni materiali - Filmi in folije - Ugotavljanje odpornosti proti zlepljenju
(ISO/FDIS 11502:2018)
Plastics - Film and sheeting - Determination of blocking resistance (ISO/FDIS
11502:2018)
Kunststoffe - Folien und Bahnen - Bestimmung des Blockwiderstandes (ISO/FDIS
11502:2018)
Plastiques - Film et feuille - Détermination du pouvoir bloquant (ISO/FDIS 11502:2018)
Ta slovenski standard je istoveten z: prEN ISO 11502
ICS:
83.140.10 Filmi in folije Films and sheets
oSIST prEN ISO 11502:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 11502:2018
---------------------- Page: 2 ----------------------
oSIST prEN ISO 11502:2018
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 11502
ISO/TC 61/SC 11
Plastics — Film and sheeting —
Secretariat: JISC
Determination of blocking resistance
Voting begins on:
20180710
Plastiques — Film et feuille — Détermination du pouvoir bloquant
Voting terminates on:
20181002
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 11502:2018(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2018
---------------------- Page: 3 ----------------------
oSIST prEN ISO 11502:2018
ISO/FDIS 11502:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 11502:2018
ISO/FDIS 11502:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Method A: Qualitative method . 1
4.1 Principle . 1
4.2 Apparatus . 1
4.3 Test specimens . 2
4.3.1 Shape and dimensions . 2
4.3.2 Preparation . 2
4.4 Procedure . 2
4.5 Test report . 3
5 Method B: Quantitative method . 3
5.1 Principle . 3
5.2 Apparatus . 3
5.3 Test specimens . 3
5.3.1 Shape and dimensions . 3
5.3.2 Preparation . 4
5.4 Procedure . 4
5.5 Precision . 4
5.6 Test report . 5
© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 11502:2018
ISO/FDIS 11502:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and nongovernmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso
.org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11,
Products.
This second edition cancels and replaces the first edition (ISO 11502:1995), of which it constitutes a
minor revision. The changes compared to the previous edition are as follows:
— Clause 2 has been updated;
— the document has been editorially revised.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2018 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 11502:2018
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 11502:2018(E)
Plastics — Film and sheeting — Determination of blocking
resistance
1 Scope
This document specifies two methods for assessing the tendency of flexible plastic films and sheets to
adhere to one another when left in contact for some time, at a specified temperature and under light
pressure. One method is qualitative and the other is quantitative.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 291, Plastics — Standard atmospheres for conditioning and testing
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
blocking
unintentional adherence between materials
4 Method A: Qualitative method
4.1 Principle
Pieces of film
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.