SIST EN 15184:2006
(Main)Products and systems for the protection and repair of concrete structures - Test methods - Shear adhesion of coated steel to concrete (pull-out test)
Products and systems for the protection and repair of concrete structures - Test methods - Shear adhesion of coated steel to concrete (pull-out test)
This European Standard specifies a method for determining the shear adhesion of steel rebar coated with a corrosion protection product or system and embedded in a standard reference concrete.
The test applies to products based on hydraulic binders or polymers or mixtures of both.
Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Prüfverfahren - Haftzugfestigkeit zwischen beschichtetem Stahl und Beton (Ausziehversuch)
Diese Europäische Norm legt ein Verfahren zur Bestimmung der Haftzugfestigkeit zwischen einem mit einem
Korrosionsschutzprodukt oder -system versehenen gerippten Bewehrungsstab aus Stahl und einem genorm-ten
Referenzbeton fest.
Diese Prüfung gilt für Produkte auf der Basis von hydraulischen Bindemitteln oder Polymeren oder deren
Gemischen.
Produits et systemes de protection et de réparation des structures en béton - Méthodes d'essai - Adhérence par cisaillement d'acier revetu au béton (essai d'arrachement)
La présente Norme européenne spécifie une méthode permettant de déterminer l’adhérence par cisaillement, d’armatures en acier revetues d’un produit ou d’un systeme de protection contre la corrosion et noyées dans un béton de référence.
La méthode d’essai s’applique aux produits a base de liants hydrauliques, de polymeres ou du mélange des deux.
Proizvodi in sistemi za zaščito in popravilo betonskih konstrukcij - Preskusne metode - Strižna adhezija zaščitenega jekla proti betonu (preskus izvleka)
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Products and systems for the protection and repair of concrete structures - Test methods - Shear adhesion of coated steel to concrete (pull-out test)Produits et systemes de protection et de réparation des structures en béton - Méthodes d'essai - Adhérence par cisaillement d'acier revetu au béton (essai d'arrachement)Produkte und Systeme für den Schutz und die Instandsetzung von Betontragwerken - Prüfverfahren - Haftzugfestigkeit zwischen beschichtetem Stahl und Beton (Ausziehversuch)Ta slovenski standard je istoveten z:EN 15184:2006SIST EN 15184:2006en91.080.40Betonske konstrukcijeConcrete structuresICS:SLOVENSKI
STANDARDSIST EN 15184:200601-december-2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15184August 2006ICS 91.080.40 English VersionProducts and systems for the protection and repair of concretestructures - Test methods - Shear adhesion of coated steel toconcrete (pull-out test)Produits et systèmes pour la protection et la réparation desstructures en béton - Méthodes d'essais - Adhérence parcisaillement d'acier revêtu au béton (essai d'arrachement)Produkte und Systeme für den Schutz und dieInstandsetzung von Betontragwerken - Prüfverfahren -Haftzugfestigkeit zwischen beschichtetem Stahl und Beton(Ausziehversuch)This European Standard was approved by CEN on 1 August 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15184:2006: E
EN 15184:2006 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Test principle.4 5 Apparatus.5 6 Preparation of the test specimens.5 7 Execution of the bond test.8 8 Test report.10 Bibliography.11
EN 15184:2006 (E) 3 Foreword This document (EN 15184:2006) has been prepared by Technical Committee CEN/TC 104 “Concrete and related products”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2007, and conflicting national standards shall be withdrawn at the latest by February 2007. This European Standard is one of a series of test method standards on products and systems for protection and repair of concrete structures; particulary it describes a method of testing the shear adhesion of products applied to reinforcing bars. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 15184:2006 (E) 4 1 Scope This European Standard specifies a method for determining the shear adhesion of steel rebar coated with a corrosion protection product or system and embedded in a standard reference concrete. The test applies to products based on hydraulic binders or polymers or mixtures of both. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 196-1, Methods of testing cement — Determination of strength EN 1504-1:2005, Products and systems for the protection and repair of concrete structures — Definitions requirements, quality control and evaluation of conformity — Part 1: Definitions EN 1504-7:2006, Products and systems for the protection and repair of concrete structures — Definitions requirements, quality control and evaluation of conformity — Part 7: Reinforcement corrosion protection ENV 1504-9:1997, Products and systems for the protection and repair of concrete structures — Definitions requirements, quality control and evaluation of conformity — Part 9: General principles for the use of products and systems EN 1766, Products and systems for the protection and repair of concrete structures — Test methods — Reference concretes for testing EN 10080, Steel for the reinforcement of concrete — Weldable reinforcing steel — General EN 12390-2, Testing hardened concrete — Part 2: Making and curing specimens for strength tests EN ISO 12944-4, Paints and varnishes — Corrosion protection of steel structures by protective paint systems — Part 4: Types of surface and surface preparation (ISO 12944-4:1998) 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 1504-1:2005, EN 1504-7:2006 and ENV 1504-9:1997 apply. 4 Test principle The test compares the shear adhesion of bars coated with a corrosion protection product or system to that of uncoated bars embedded in a standard reference concrete. The test is carried out using concrete specimens in which coated and uncoated rebars are embedded. A tensile load is applied to one end of the rebar and increased at a controlled rate until failure occurs. The applied force and resulting displacement are measured for each of the coated and uncoated rebars and the results compared.
EN 15184:2006 (E) 5 5 Apparatus 5.1 Concrete mixer in accordance with EN 196-1, or a forced action pan mixer. 5.2 Compaction tools and equipment in accordance with EN 196-1. 5.3 Stirrer and brush to mix and apply the coating product. 5.4 Moulds for the preparation of cubes of dimensions 200 mm × 200 mm × 200 mm (see Figure 1). 5.5 Thermometer accurate to within 1 °C. 5.6 Tensile testing apparatus of adequate capacity, capable of measuring load to an accuracy of ± 2 %, and fitted with a load pacer to control the rate of load increase. 5.7 A measuring device, interlocked with the rebar and one or more displacement sensors, capable of measuring relative movement between the anchored bar and a fixed reference
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.