SIST EN 301 908-13 V7.1.1:2016
(Main)IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
The present document covers requirements for E-UTRA FDD and E-UTRA TDD User Equipment from 3GPP
Releases 8, 9, 10 and 11 defined in ETSI TS 136 101 [4]. This includes the requirements for E-UTRA UE operating
bands and E-UTRA CA operating bands from 3GPP Release 12 defined in ETSI TS 136 101 [i.14].
NOTE 1: For Band 20:
For user equipment designed to be mobile or nomadic, the requirements in the present document
measured at the antenna port also show conformity to the corresponding requirement defined as
TRP (total radiated power), as described in Commission Decision 2010/267/EU [i.7], ECC
Decision (09)03 [i.8] and CEPT Report 30 [i.9].
For user equipment designed to be fixed or installed, the present document does not address the
requirements described in Commission Decision 2010/267/EU [i.7], ECC Decision (09)03 [i.8] and
CEPT Report 30 [i.9].
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), article 3.2,
which states that "….. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
Celična omrežja IMT - Harmonizirani EN, ki zajema bistvene zahteve člena 3.2 direktive R&TTE - 13. del: Uporabniška oprema za razviti prizemni radijski dostop za UMTS (E-UTRA)
Ta dokument zajema zahteve za uporabniško opremo E-UTRA FDD in E-UTRA TDD iz izdaj 8, 9, 10 in 11 dokumenta 3GPP, kot je določeno v dokumentu ETSI TS 136 101 [4]. To vključuje zahteve za pasove, v katerih deluje E-UTRA UE, in pasove, v katerih deluje E-UTRA CA iz izdaje 12 dokumenta 3GPP, kot je določeno v dokumentu ETSI TS 136 101 [i.14].
OPOMBA 1: Za pas 20:
Za uporabniško opremo, zasnovano kot mobilno ali nomadsko, so zahteve iz tega dokumenta, izmerjene na antenskem vhodu, tudi v skladu z ustrezno zahtevo, opredeljeno kot TRP (skupna sevana moč), kot je opisana v Sklepu Komisije 2010/267/EU [i.7], Sklepu Odbora za elektronske komunikacije (09)03 [i.8] in poročilu CEPT 30 [i.9].
Za uporabniško opremo, zasnovano za priključitev ali namestitev, ta dokument ne obravnava zahtev, opisanih v Sklepu Komisije 2010/267/EU [i.7], Sklepu Odbora za elektronske komunikacije (09)03 [i.8] in poročilu CEPT 30 [i.9].
Ta dokument zajema določbe člena 3.2 Direktive 1999/5/ES [i.2] (direktive R&TTE), ki določa, da »... mora biti radijska oprema skonstruirana tako, da učinkovito uporablja spekter, razporejen za prizemne/vesoljske radijske komunikacije in orbitalne vire, tako da ne pride do škodljivega motenja.«
Poleg tega dokumenta se lahko za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov člena 3 direktive R&TTE [i.2].
General Information
Buy Standard
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-13 V7.1.1SIST EN 301 908-13 V7.1.1:2016en01-marec-2016SIST EN 301 908-13 V7.1.1:2016SLOVENSKI
STANDARD
SIST EN 301 908-13 V7.1.1:2016
ETSI EN 301 908-13 V7.1.1 (2015-12) IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)
HARMONISED EUROPEAN STANDARD SIST EN 301 908-13 V7.1.1:2016
ETSI ETSI EN 301 908-13 V7.1.1 (2015-12)2
Reference REN/MSG-TFES-011-13 Keywords 3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE, LTE-Advanced, mobile, radio, regulation, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-13 V7.1.1:2016
ETSI ETSI EN 301 908-13 V7.1.1 (2015-12)3 Contents Intellectual Property Rights . 8 Foreword . 8 Modal verbs terminology . 8 Introduction . 8 1 Scope . 9 2 References . 11 2.1 Normative references . 11 2.2 Informative references . 12 3 Definitions, symbols and abbreviations . 13 3.1 Definitions . 13 3.2 Symbols . 15 3.3 Abbreviations . 17 4 Technical requirements specifications . 18 4.1 Environmental profile . 18 4.2 Conformance requirements . 18 4.2.1 Introduction. 18 4.2.2 Transmitter Maximum Output Power . 19 4.2.2.1 Transmitter maximum output power for Single Carrier . 19 4.2.2.1.1 Definition. 19 4.2.2.1.2 Limits . 19 4.2.2.1.3 Conformance . 19 4.2.2.2 Transmitter output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA). 19 4.2.2.2.1 Definition. 19 4.2.2.2.2 Limits . 20 4.2.2.2.3 Conformance . 20 4.2.2.3 Transmitter output power for UL-MIMO . 20 4.2.2.3.1 Definition. 20 4.2.2.3.2 Limits . 21 4.2.2.3.3 Conformance . 21 4.2.3 Transmitter Spectrum Emission Mask . 21 4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 21 4.2.3.1.1 Definition. 21 4.2.3.1.2 Limits . 21 4.2.3.1.3 Conformance . 23 4.2.3.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 23 4.2.3.2.1 Definition. 23 4.2.3.2.2 Limits . 23 4.2.3.2.3 Conformance . 24 4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 24 4.2.3.3.1 Definition. 24 4.2.3.3.2 Limits . 24 4.2.3.3.3 Conformance . 24 4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 24 4.2.3.4.1 Definition. 24 4.2.3.4.2 Limits . 24 4.2.3.4.3 Conformance . 25 4.2.4 Transmitter Spurious Emissions . 25 4.2.4.1 Transmitter spurious emissions for Single Carrier . 25 4.2.4.1.1 Definition. 25 4.2.4.1.2 Limits . 25 4.2.4.1.3 Conformance . 28 4.2.4.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 28 SIST EN 301 908-13 V7.1.1:2016
ETSI ETSI EN 301 908-13 V7.1.1 (2015-12)4 4.2.4.2.1 Definition. 28 4.2.4.2.2 Limits . 28 4.2.4.2.3 Conformance . 30 4.2.4.3 Transmitter spurious emissions for UL-MIMO . 30 4.2.4.3.1 Definition. 30 4.2.4.3.2 Limits . 31 4.2.4.3.3 Conformance . 31 4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 31 4.2.4.4.1 Definition. 31 4.2.4.4.2 Limits . 31 4.2.4.4.3 Conformance . 31 4.2.5 Transmitter Minimum Output Power . 31 4.2.5.1 Transmitter minimum output power for Single Carrier. 31 4.2.5.1.1 Definition. 31 4.2.5.1.2 Limits . 31 4.2.5.1.3 Conformance . 31 4.2.5.2 Transmitter minimum output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 32 4.2.5.2.1 Definition. 32 4.2.5.2.2 Limits . 32 4.2.5.2.3 Conformance . 32 4.2.5.3 Transmitter minimum output power for UL-MIMO . 32 4.2.5.3.1 Definition. 32 4.2.5.3.2 Limits . 32 4.2.5.3.3 Conformance . 32 4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 33 4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 33 4.2.6.1.1 Definition. 33 4.2.6.1.2 Limits . 33 4.2.6.1.3 Conformance . 33 4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 34 4.2.6.2.1 Definition. 34 4.2.6.2.2 Limits . 34 4.2.6.2.3 Conformance . 34 4.2.7 Receiver Blocking Characteristics . 34 4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 34 4.2.7.1.1 Definition. 34 4.2.7.1.2 Limits . 34 4.2.7.1.3 Conformance . 36 4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 36 4.2.7.2.1 Definition. 36 4.2.7.2.2 Limits . 36 4.2.7.2.3 Conformance . 37 4.2.8 Receiver Spurious Response . 37 4.2.8.1 Receiver Spurious Response for Single Carrier . 37 4.2.8.1.1 Definition. 37 4.2.8.1.2 Limits . 37 4.2.8.1.3 Conformance . 38 4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 38 4.2.8.2.1 Definition. 38 4.2.8.2.2 Limits . 38 4.2.8.2.3 Conformance . 38 4.2.9 Receiver Intermodulation Characteristics . 38 4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 38 4.2.9.1.1 Definition. 38 4.2.9.1.2 Limits . 38 4.2.9.1.3 Conformance . 39 4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 39 4.2.9.2.1 Definition. 39 4.2.9.2.2 Limits . 39 4.2.9.2.3 Conformance . 39 4.2.10 Receiver Spurious Emissions . 39 SIST EN 301 908-13 V7.1.1:2016
ETSI ETSI EN 301 908-13 V7.1.1 (2015-12)5 4.2.10.1 Receiver Spurious Emissions for Single Carrier . 39 4.2.10.1.1 Definition. 39 4.2.10.1.2 Limits . 39 4.2.10.1.3 Conformance . 40 4.2.10.2 Receiver Spurious Emissions in DL-only bands . 40 4.2.10.2.1 Definition. 40 4.2.10.2.2 Limits . 40 4.2.10.2.3 Conformance . 40 4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 40 4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 40 4.2.11.1.1 Definition. 40 4.2.11.1.2 Limits . 40 4.2.11.1.3 Conformance . 41 4.2.11.2 Transmitter adjacent channel leakage power ratio for intra-band contiguous Carrier Aggregation (DL CA and UL CA). 41 4.2.11.2.1 Definition. 41 4.2.11.2.2 Limits . 42 4.2.11.2.3 Conformance . 42 4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 43 4.2.11.3.1 Definition. 43 4.2.11.3.2 Limits . 43 4.2.11.3.3 Conformance . 44 4.2.11.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component carrier . 44 4.2.11.4.1 Definition. 44 4.2.11.4.2 Limits . 44 4.2.11.4.3 Conformance . 44 5 Testing for compliance with technical requirements . 45 5.1 Environmental conditions for testing . 45 5.2 Interpretation of the measurement results . 45 5.3 Essential radio test suites . 46 5.3.1 Transmitter Maximum Output Power . 46 5.3.1.1 Transmitter maximum output power for Single Carrier . 46 5.3.1.1.1 Method of test . 46 5.3.1.1.2 Test requirements . 47 5.3.1.2 Transmitter maximum output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 47 5.3.1.2.1 Method of test . 47 5.3.1.2.2 Test requirements . 48 5.3.1.3 Transmitter maximum output power for UL-MIMO . 48 5.3.1.3.1 Method of test . 48 5.3.1.3.2 Test requirements . 48 5.3.2 Transmitter Spectrum Emission Mask . 49 5.3.2.1 Transmitter spectrum emission mask for Single Carrier . 49 5.3.2.1.1 Method of test . 49 5.3.2.1.2 Test requirements . 49 5.3.2.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 49 5.3.2.2.1 Method of test . 49 5.3.2.2.2 Test requirements . 50 5.3.2.3 Transmitter spectrum emission mask for UL-MIMO . 50 5.3.2.3.1 Method of test . 50 5.3.2.3.2 Test requirements . 51 5.3.2.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 51 5.3.2.4.1 Method of test . 51 5.3.2.4.2 Test requirements . 52 5.3.3 Transmitter Spurious Emissions . 52 5.3.3.1 Transmitter spurious emissions for Single Carrier . 52 5.3.3.1.1 Method of test . 52 5.3.3.1.2 Test requirements .
...
Final draft ETSI EN 301 908-13 V7.1.0 (2015-10)
HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-13 V7.1.0 (2015-10)
Reference
REN/MSG-TFES-011-13
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-13 V7.1.0 (2015-10)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definitions, symbols and abbreviations . 13
3.1 Definitions . 13
3.2 Symbols . 15
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Conformance requirements . 18
4.2.1 Introduction. 18
4.2.2 Transmitter Maximum Output Power . 19
4.2.2.1 Transmitter maximum output power for Single Carrier . 19
4.2.2.1.1 Definition. 19
4.2.2.1.2 Limits . 19
4.2.2.1.3 Conformance . 19
4.2.2.2 Transmitter output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA). 19
4.2.2.2.1 Definition. 19
4.2.2.2.2 Limits . 20
4.2.2.2.3 Conformance . 20
4.2.2.3 Transmitter output power for UL-MIMO . 20
4.2.2.3.1 Definition. 20
4.2.2.3.2 Limits . 21
4.2.2.3.3 Conformance . 21
4.2.3 Transmitter Spectrum Emission Mask . 21
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 21
4.2.3.1.1 Definition. 21
4.2.3.1.2 Limits . 21
4.2.3.1.3 Conformance . 23
4.2.3.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 23
4.2.3.2.1 Definition. 23
4.2.3.2.2 Limits . 23
4.2.3.2.3 Conformance . 24
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 24
4.2.3.3.1 Definition. 24
4.2.3.3.2 Limits . 24
4.2.3.3.3 Conformance . 24
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 24
4.2.3.4.1 Definition. 24
4.2.3.4.2 Limits . 24
4.2.3.4.3 Conformance . 25
4.2.4 Transmitter Spurious Emissions . 25
4.2.4.1 Transmitter spurious emissions for Single Carrier . 25
4.2.4.1.1 Definition. 25
4.2.4.1.2 Limits . 25
4.2.4.1.3 Conformance . 28
4.2.4.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 28
ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-13 V7.1.0 (2015-10)
4.2.4.2.1 Definition. 28
4.2.4.2.2 Limits . 28
4.2.4.2.3 Conformance . 30
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 30
4.2.4.3.1 Definition. 30
4.2.4.3.2 Limits . 31
4.2.4.3.3 Conformance . 31
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 31
4.2.4.4.1 Definition. 31
4.2.4.4.2 Limits . 31
4.2.4.4.3 Conformance . 31
4.2.5 Transmitter Minimum Output Power . 31
4.2.5.1 Transmitter minimum output power for Single Carrier. 31
4.2.5.1.1 Definition. 31
4.2.5.1.2 Limits . 31
4.2.5.1.3 Conformance . 31
4.2.5.2 Transmitter minimum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 32
4.2.5.2.1 Definition. 32
4.2.5.2.2 Limits . 32
4.2.5.2.3 Conformance . 32
4.2.5.3 Transmitter minimum output power for UL-MIMO . 32
4.2.5.3.1 Definition. 32
4.2.5.3.2 Limits . 32
4.2.5.3.3 Conformance . 32
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 33
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 33
4.2.6.1.1 Definition. 33
4.2.6.1.2 Limits . 33
4.2.6.1.3 Conformance . 33
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 34
4.2.6.2.1 Definition. 34
4.2.6.2.2 Limits . 34
4.2.6.2.3 Conformance . 34
4.2.7 Receiver Blocking Characteristics . 34
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 34
4.2.7.1.1 Definition. 34
4.2.7.1.2 Limits . 34
4.2.7.1.3 Conformance . 36
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 36
4.2.7.2.1 Definition. 36
4.2.7.2.2 Limits . 36
4.2.7.2.3 Conformance . 37
4.2.8 Receiver Spurious Response . 37
4.2.8.1 Receiver Spurious Response for Single Carrier . 37
4.2.8.1.1 Definition. 37
4.2.8.1.2 Limits . 37
4.2.8.1.3 Conformance . 38
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 38
4.2.8.2.1 Definition. 38
4.2.8.2.2 Limits . 38
4.2.8.2.3 Conformance . 38
4.2.9 Receiver Intermodulation Characteristics . 38
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 38
4.2.9.1.1 Definition. 38
4.2.9.1.2 Limits . 38
4.2.9.1.3 Conformance . 39
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 39
4.2.9.2.1 Definition. 39
4.2.9.2.2 Limits . 39
4.2.9.2.3 Conformance . 39
4.2.10 Receiver Spurious Emissions . 39
ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-13 V7.1.0 (2015-10)
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 39
4.2.10.1.1 Definition. 39
4.2.10.1.2 Limits . 39
4.2.10.1.3 Conformance . 40
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 40
4.2.10.2.1 Definition. 40
4.2.10.2.2 Limits . 40
4.2.10.2.3 Conformance . 40
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 40
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 40
4.2.11.1.1 Definition. 40
4.2.11.1.2 Limits . 40
4.2.11.1.3 Conformance . 41
4.2.11.2 Transmitter adjacent channel leakage power ratio for intra-band contiguous Carrier Aggregation
(DL CA and UL CA). 41
4.2.11.2.1 Definition. 41
4.2.11.2.2 Limits . 42
4.2.11.2.3 Conformance . 42
4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 43
4.2.11.3.1 Definition. 43
4.2.11.3.2 Limits . 43
4.2.11.3.3 Conformance . 44
4.2.11.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component
carrier . 44
4.2.11.4.1 Definition. 44
4.2.11.4.2 Limits . 44
4.2.11.4.3 Conformance . 44
5 Testing for compliance with technical requirements . 45
5.1 Environmental conditions for testing . 45
5.2 Interpretation of the measurement results . 45
5.3 Essential radio test suites . 46
5.3.1 Transmitter Maximum Output Power . 46
5.3.1.1 Transmitter maximum output power for Single Carrier . 46
5.3.1.1.1 Method of test . 46
5.3.1.1.2 Test requirements . 47
5.3.1.2 Transmitter maximum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 47
5.3.1.2.1 Method of test . 47
5.3.1.2.2 Test requirements . 48
5.3.1.3 Transmitter maximum output power for UL-MIMO . 48
5.3.1.3.1 Method of test . 48
5.3.1.3.2 Test requirements . 48
5.3.2 Transmitter Spectrum Emission Mask . 49
5.3.2.1 Transmitter spectrum emission mask for Single Carrier . 49
5.3.2.1.1 Method of test . 49
5.3.2.1.2 Test requirements . 49
5.3.2.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 49
5.3.2.2.1 Method of test . 49
5.3.2.2.2 Test requirements . 50
5.3.2.3 Transmitter spectrum emission mask for UL-MIMO . 50
5.3.2.3.1 Method of test . 50
5.3.2.3.2 Test requirements . 51
5.3.2.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 51
5.3.2.4.1 Method of test . 51
5.3.2.4.2 Test requirements . 52
5.3.3 Transmitter Spurious Emissions . 52
5.3.3.1 Transmitter spurious emissions for Single Carrier . 52
5.3.3.1.1 Method of test . 52
5.3.3.1.2 Test requirements . 53
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 908-13 V7.1.0 (2015-10)
...
Draft ETSI EN 301 908-13 V7.0.1 (2015-05)
HARMONIZED EUROPEAN STANDARD
IMT cellular networks;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-13 V7.0.1 (2015-05)
Reference
REN/MSG-TFES-011-13
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2015.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-13 V7.0.1 (2015-05)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definitions, symbols and abbreviations . 13
3.1 Definitions . 13
3.2 Symbols . 15
3.3 Abbreviations . 17
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Conformance requirements . 18
4.2.1 Introduction. 19
4.2.2 Transmitter Maximum Output Power . 19
4.2.2.1 Transmitter maximum output power for Single Carrier . 19
4.2.2.1.1 Definition. 19
4.2.2.1.2 Limits . 20
4.2.2.1.3 Conformance . 20
4.2.2.2 Transmitter output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA). 20
4.2.2.2.1 Definition. 20
4.2.2.2.2 Limits . 21
4.2.2.2.3 Conformance . 21
4.2.2.3 Transmitter output power for UL-MIMO . 21
4.2.2.3.1 Definition. 21
4.2.2.3.2 Limits . 22
4.2.2.3.3 Conformance . 22
4.2.3 Transmitter Spectrum Emission Mask . 22
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 22
4.2.3.1.1 Definition. 22
4.2.3.1.2 Limits . 22
4.2.3.1.3 Conformance . 24
4.2.3.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 24
4.2.3.2.1 Definition. 24
4.2.3.2.2 Limits . 24
4.2.3.2.3 Conformance . 25
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 25
4.2.3.3.1 Definition. 25
4.2.3.3.2 Limits . 25
4.2.3.3.3 Conformance . 25
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 25
4.2.3.4.1 Definition. 25
4.2.3.4.2 Limits . 25
4.2.3.4.3 Conformance . 26
4.2.4 Transmitter Spurious Emissions . 26
4.2.4.1 Transmitter spurious emissions for Single Carrier . 26
4.2.4.1.1 Definition. 26
4.2.4.1.2 Limits . 26
4.2.4.1.3 Conformance . 29
4.2.4.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 29
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-13 V7.0.1 (2015-05)
4.2.4.2.1 Definition. 29
4.2.4.2.2 Limits . 29
4.2.4.2.3 Conformance . 31
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 31
4.2.4.3.1 Definition. 31
4.2.4.3.2 Limits . 32
4.2.4.3.3 Conformance . 32
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 32
4.2.4.4.1 Definition. 32
4.2.4.4.2 Limits . 32
4.2.4.4.3 Conformance . 32
4.2.5 Transmitter Minimum Output Power . 32
4.2.5.1 Transmitter minimum output power for Single Carrier. 32
4.2.5.1.1 Definition. 32
4.2.5.1.2 Limits . 32
4.2.5.1.3 Conformance . 32
4.2.5.2 Transmitter minimum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 33
4.2.5.2.1 Definition. 33
4.2.5.2.2 Limits . 33
4.2.5.2.3 Conformance . 33
4.2.5.3 Transmitter minimum output power for UL-MIMO . 33
4.2.5.3.1 Definition. 33
4.2.5.3.2 Limits . 33
4.2.5.3.3 Conformance . 33
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 34
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 34
4.2.6.1.1 Definition. 34
4.2.6.1.2 Limits . 34
4.2.6.1.3 Conformance . 34
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 35
4.2.6.2.1 Definition. 35
4.2.6.2.2 Limits . 35
4.2.6.2.3 Conformance . 35
4.2.7 Receiver Blocking Characteristics . 35
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 35
4.2.7.1.1 Definition. 35
4.2.7.1.2 Limits . 35
4.2.7.1.3 Conformance . 37
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 37
4.2.7.2.1 Definition. 37
4.2.7.2.2 Limits . 37
4.2.7.2.3 Conformance . 38
4.2.8 Receiver Spurious Response . 38
4.2.8.1 Receiver Spurious Response for Single Carrier . 38
4.2.8.1.1 Definition. 38
4.2.8.1.2 Limits . 38
4.2.8.1.3 Conformance . 39
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 39
4.2.8.2.1 Definition. 39
4.2.8.2.2 Limits . 39
4.2.8.2.3 Conformance . 39
4.2.9 Receiver Intermodulation Characteristics . 39
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 39
4.2.9.1.1 Definition. 39
4.2.9.1.2 Limits . 39
4.2.9.1.3 Conformance . 40
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 40
4.2.9.2.1 Definition. 40
4.2.9.2.2 Limits . 40
4.2.9.2.3 Conformance . 40
4.2.10 Receiver Spurious Emissions . 40
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-13 V7.0.1 (2015-05)
4.2.10.1 Definition . 40
4.2.10.2 Limits . 40
4.2.10.3 Conformance . 41
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 41
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 41
4.2.11.1.1 Definition. 41
4.2.11.1.2 Limits . 41
4.2.11.1.3 Conformance . 42
4.2.11.2 Transmitter adjacent channel leakage power ratio for intra-band contiguous Carrier Aggregation
(DL CA and UL CA). 42
4.2.11.2.1 Definition. 42
4.2.11.2.2 Limits . 43
4.2.11.2.3 Conformance . 43
4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 43
4.2.11.3.1 Definition. 43
4.2.11.3.2 Limits . 44
4.2.11.3.3 Conformance . 45
4.2.11.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component
carrier . 45
4.2.11.4.1 Definition. 45
4.2.11.4.2 Limits . 45
4.2.11.4.3 Conformance . 45
5 Testing for compliance with technical requirements . 45
5.1 Environmental conditions for testing . 45
5.2 Interpretation of the measurement results . 45
5.3 Essential radio test suites . 46
5.3.1 Transmitter Maximum Output Power . 46
5.3.1.1 Transmitter maximum output power for Single Carrier . 46
5.3.1.1.1 Method of test . 46
5.3.1.1.2 Test requirements . 47
5.3.1.2 Transmitter maximum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 47
5.3.1.2.1 Method of test . 47
5.3.1.2.2 Test requirements . 48
5.3.1.3 Transmitter maximum output power for UL-MIMO . 48
5.3.1.3.1 Method of test . 48
5.3.1.3.2 Test requirements . 49
5.3.2 Transmitter Spectrum Emission Mask . 49
5.3.2.1 Transmitter spectrum emission mask for Single Carrier . 49
5.3.2.1.1 Method of test . 49
5.3.2.1.2 Test requirements . 50
5.3.2.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 50
5.3.2.2.1 Method of test . 50
5.3.2.2.2 Test requirements . 50
5.3.2.3 Transmitter spectrum emission mask for UL-MIMO . 51
5.3.2.3.1 Method of test . 51
5.3.2.3.2 Test requirements . 51
5.3.2.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 51
5.3.2.4.1 Method of test . 51
5.3.2.4.2 Test requirements . 52
5.3.3 Transmitter Spurious Emissions . 52
5.3.3.1 Transmitter spurious emissions for Single Carrier . 52
5.3.3.1.1 Method of test . 52
5.3.3.1.2 Test requirements . 53
5.3.3.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 53
5.3.3.2.1 Method of test . 53
5.3.3.2.2 Test requirements . 54
5.3.3.3 Transmitter spurious emissions for UL-MIMO . 54
5.3.3.3.1 Method of test . 54
ETSI
-----------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.