SIST EN 62150-3:2012

Fibre optic active components and devices - Test and measurement procedures - Part 3: Optical power variation induced by mechanical disturbance in optical receptacles and transceiver interfaces (IEC 62150-3:2012)

The purpose of this part of IEC 62150 is to specify the test requirements and procedures for qualifying optical devices for sensitivity to coupled power variations induced by mechanical disturbance at the optical ports of the device. It applies to active devices with optical receptacle interfaces. In this edition, transceivers using small-form-factor connector cables (1,25 mm ferrule) for single mode fibre are specified. It has been found that some optical transceivers and receptacles are susceptible to fibre optic cable induced stress when side forces are applied to the mated cable-connector assembly, resulting in variations in the transmitted optical power. This part of IEC 62150 defines physical stress tests to ensure that such optical connections (cable and receptacle) can continue to function within specifications.

Aktive Lichtwellenleiter-Bauteile und -Bauelemente - Grundlegende Prüf- und Messverfahren - Teil 3: Optische Leistungsabweichungen bedingt durch mechanische Störungen an Schnittstellen optischer Steckverbinder und Transceivern (IEC 62150-3:2012)

Composants et dispositifs actifs à fibres optiques - Procédures d'essais et de mesures - Partie 3: Variation de puissance optique induite par des perturbations mécaniques dans les interfaces d'émetteurs-récepteurs et d'embases optiques (CEI 62150-3:2012)

La CEI 62150-3:2012 spécifie les exigences d'essais et les procédures pour qualifier la sensibilité de dispositifs optiques à des variations de la puissance couplée induites par des perturbations mécaniques au niveau des ports optiques du dispositif. Elle s'applique aux dispositifs actifs dotés d'interfaces d'embases optiques. Dans la présente édition, on spécifie des émetteurs-récepteurs utilisant des câbles de connexion à petit facteur de forme (férule de 1,25 mm) pour des fibres unimodales.   Mots clé: perturbations mécaniques

Aktivne optične komponente in naprave - Preskuševalni in merilni postopki - 3. del: Spreminjanje optične moči zaradi mehanskih motenj v optičnih sprejemnikih in oddajno-sprejemniških vmesnikih (IEC 62150-3:2012)

Namen tega dela standarda IEC 62150 je določiti preskusne zahteve in postopke za razvrstitev optičnih naprav glede na občutljivost spreminjanja moči, ki jih povzročajo mehanske motnje pri optičnih vhodih naprave. To velja za dejavne naprave z vmesniki optičnega sprejemnika. V tej izdaji so opredeljeni oddajniki-sprejemniki s priključnimi kabli SFF (tulka velikosti 1,25 mm) za enorodovno vlakno. Ugotovljeno je bilo, da so nekateri optični oddajniki-sprejemniki in sprejemniki med uporabo stranskih sil pri sestavu kabla in priključka občutljivi na napetost kabla iz optičnih vlaken zaradi sprememb v oddajani optični moči. Ta del standarda IEC 62150 določa preskuse fizične napetosti za zagotovitev nadaljnjega delovanja takšnih optičnih povezav (kabelskih in z vtičnico) v okviru specifikacij.

General Information

• Status: Withdrawn
• Publication Date: 08-Oct-2012
• Withdrawal Date: 19-Aug-2018
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: MOC - Mobile Communications
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 09-Aug-2018
• Due Date: 01-Sep-2018
• Completion Date: 20-Aug-2018
• Ref Project: EN 62150-3:2012 - Fibre optic active components and devices - Test and measurement procedures - Part 3: Optical power variation induced by mechanical disturbance in optical receptacles and transceiver interfaces

Relations

• Revised: SIST EN 62150-3:2016 - Fibre optic active components and devices - Test and measurement procedures - Part 3: Optical power variation induced by mechanical disturbance in optical receptacles and transceiver interfaces (IEC 62150-3:2015)
• Effective Date: 06-May-2014
• Replaced By: SIST EN 62150-3:2016 - Fibre optic active components and devices - Test and measurement procedures - Part 3: Optical power variation induced by mechanical disturbance in optical receptacles and transceiver interfaces (IEC 62150-3:2015)
• Effective Date: 28-Jan-2023
• Replaced By: SIST EN 62150-3:2016 - Fibre optic active components and devices - Test and measurement procedures - Part 3: Optical power variation induced by mechanical disturbance in optical receptacles and transceiver interfaces (IEC 62150-3:2015)
• Effective Date: 07-Jun-2022
• Replaced By: SIST EN 62150-3:2016 - Fibre optic active components and devices - Test and measurement procedures - Part 3: Optical power variation induced by mechanical disturbance in optical receptacles and transceiver interfaces (IEC 62150-3:2015)
• Effective Date: 25-Feb-2014

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 62150-3:2012
01-november-2012
$NWLYQHRSWLþQHNRPSRQHQWHLQQDSUDYH3UHVNXãHYDOQLLQPHULOQLSRVWRSNL
GHO6SUHPLQMDQMHRSWLþQHPRþL]DUDGLPHKDQVNLKPRWHQMYRSWLþQLKVSUHMHPQLNLK
LQRGGDMQRVSUHMHPQLãNLKYPHVQLNLK,(&
Fibre optic active components and devices - Test and measurement procedures - Part 3:
Optical power variation induced by mechanical disturbance in optical receptacles and
transceiver interfaces (IEC 62150-3:2012)
Aktive Lichtwellenleiter-Bauteile und -Bauelemente - Grundlegende Prüf- und
Messverfahren - Teil 3: Optische Leistungsabweichungen bedingt durch mechanische
Störungen an Schnittstellen optischer Steckverbinder und Transceivern (IEC 62150-
3:2012)
Composants et dispositifs actifs à fibres optiques - Procédures d'essais et de mesures -
Partie 3: Variation de puissance optique induite par des perturbations mécaniques dans
les interfaces d'émetteurs-récepteurs et d'embases optiques (CEI 62150-3:2012)
Ta slovenski standard je istoveten z: EN 62150-3:2012
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 62150-3:2012 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 62150-3:2012

---------------------- Page: 2 ----------------------

SIST EN 62150-3:2012

EUROPEAN STANDARD
EN 62150-3

NORME EUROPÉENNE
September 2012
EUROPÄISCHE NORM

ICS 33.180.20


English version


Fibre optic active components and devices -
Test and measurement procedures -
Part 3: Optical power variation induced by mechanical disturbance in
optical receptacles and transceiver interfaces
(IEC 62150-3:2012)


Composants et dispositifs actifs à fibres Aktive Lichtwellenleiter-Bauteile und -
optiques - Bauelemente -
Procédures d'essais et de mesures - Grundlegende Prüf- und Messverfahren -
Partie 3: Variation de puissance optique Teil 3: Optische Leistungsabweichungen
induite par des perturbations mécaniques bedingt durch mechanische Störungen in
dans les interfaces d'embases optiques et optischen Kupplungen und Transceiver-
d'émetteurs-récepteurs Schnittstellen
(CEI 62150-3:2012) (IEC 62150-3:2012)



This European Standard was approved by CENELEC on 2012-08-13. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62150-3:2012 E

---------------------- Page: 3 ----------------------

SIST EN 62150-3:2012
EN 62150-3:2012 - 2 -

Foreword
The text of document 86C/1061/FDIS, future edition 1 of IEC 62150-3, prepared by SC 86C, "Fibre optic
systems and active devices", of IEC TC 86, "Fibre optics" was submitted to the IEC-CENELEC parallel
vote and approved by CENELEC as EN 62150-3:2012.

The following dates are fixed:
(dop) 2013-05-13
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-08-13

standards conflicting with the
document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.

Endorsement notice
The text of the International Standard IEC 62150-3:2012 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 61300 (series) NOTE  Harmonized in EN 61300 series (not modified).

---------------------- Page: 4 ----------------------

SIST EN 62150-3:2012
- 3 - EN 62150-3:2012

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 61753 Series Fibre optic interconnecting devices and EN 61753 Series
passive components performance standard


IEC 61753-021-6 - Fibre optic interconnecting devices and EN 61753-021-6 -
passive components performance standard -
Part 021-6: Grade B/2 single-mode fibre optic
connectors for category O - Uncontrolled
environment


IEC 61754 Series Fibre optic connector interfaces EN 61754 Series

---------------------- Page: 5 ----------------------

SIST EN 62150-3:2012

---------------------- Page: 6 ----------------------

SIST EN 62150-3:2012




IEC 62150-3

®


Edition 1.0 2012-07




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE
colour

inside










Fibre optic active components and devices – Test and measurement

procedures –

Part 3: Optical power variation induced by mechanical disturbance in optical


receptacles and transceiver interfaces



Composants et dispositifs actifs à fibres optiques – Procédures d'essais et de


mesures –

Partie 3: Variation de puissance optique induite par des perturbations

mécaniques dans les interfaces d'embases optiques et d'émetteurs-récepteurs










INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX S


ICS 33.180.20 ISBN 978-2-83220-157-2



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 62150-3:2012
– 2 – 62150-3 © IEC:2012
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references. 6
3 Terms, definitions and abbreviations . 6
3.1 Terms and definitions . 6
3.2 Abbreviations . 7
4 Measurement consideration . 7
4.1 Multiple test methods . 7
4.2 Two wiggle loss mechanisms . 7
4.2.1 Rationale for two different wiggle loss test methods. 7
4.2.2 Case A: Point of action for the ferrule . 8
4.2.3 Case B: Point of action for the plug housing . 8
5 Test method A . 8
5.1 Apparatus . 8
5.1.1 Apparatus . 8
5.1.2 Test cord . 8
5.1.3 Power meter . 8
5.1.4 Test load . 8
5.2 Test procedures for Tx interfaces . 9
5.2.1 Test procedures . 9
5.2.2 Set up . 9
5.2.3 Initial measurement . 9
5.2.4 Apply load and rotate . 9
5.2.5 Wiggle loss . 10
5.3 Test procedures for Rx interfaces and optical receptors . 10
5.3.1 Test procedures . 10
5.3.2 LOS indicator method . 10
5.3.3 Receiver optical power monitor method . 10
6 Test method B . 11
6.1 Apparatus . 11
6.1.1 Apparatus . 11
6.1.2 Test fixture and rotation mechanism . 11
6.1.3 Test cord . 11
6.1.4 Power meter . 11
6.1.5 Test load . 11
6.2 Test procedures for Tx interfaces . 11
6.2.1 Test procedures . 11
6.2.2 Set up . 12
6.2.3 Initial measurement . 12
6.2.4 Apply load . 12
6.2.5 Measurement . 12
6.2.6 Wiggle loss . 12
6.3 Test procedures for Rx interfaces and optical receptors . 13
6.3.1 Test procedures . 13
6.3.2 LOS indicator method . 13
6.3.3 Receiver optical power monitor method . 13

---------------------- Page: 8 ----------------------

SIST EN 62150-3:2012
62150-3 © IEC:2012 – 3 –
7 Test results . 14
Annex A (normative) Load requirements . 15
Annex B (normative) Summary of test conditions . 16
Annex C (normative) Characteristics of test cord . 17
Annex D (normative) Floating tolerance . 19
Bibliography . 20

Figure 1 – Equipment setup of Method A for Tx interfaces . 9
Figure 2 – Equipment setup of Method A for Rx interfaces and optical receptors . 10
Figure 3 – Equipment setup of Method B for Tx interfaces . 12
Figure 4 – Equipment setup of Method B for Rx interface and optical receptors. 13
Figure C.1 – Wiggle test cord interface . 17
Figure D.1 – Floating tolerance . 19

Table 1 – Multiple test methods . 7
Table A.1 – Method A: Loads applied for devices using small-form-factor connector
cords (1,25 mm ferrule) . 15
Table A.2 – Method B: Loads applied for devices using small-form-factor connector
cords (1,25 mm ferrule) . 15
Table B.1 – Summary of test conditions for Method A (normative) . 16
Table B.2 – Summary of test conditions for Method B (normative) . 16
Table C.1 – Wiggle test cord specification . 17
Table C.2 – Dimensions of the wiggle test cord interface . 18

---------------------- Page: 9 ----------------------

SIST EN 62150-3:2012
– 4 – 62150-3 © IEC:2012
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
TEST AND MEASUREMENT PROCEDURES –

Part 3: Optical power variation induced by mechanical disturbance
in optical receptacles and transceiver interfaces


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62150-3 has been prepared by subcommittee 86C: Fibre optic
systems and active devices 86: Fibre optics.
The text of this standard is based on the following documents:
FDIS Report on voting
86C/1061/FDIS 86C/1072/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 10 ----------------------

SIST EN 62150-3:2012
62150-3 © IEC:2012 – 5 –
The committee has decided that the contents of this publication will remain unchanged until the
stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to
the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this document using a colour printer.

---------------------- Page: 11 ----------------------

SIST EN 62150-3:2012
– 6 – 62150-3 © IEC:2012
FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES –
TEST AND MEASUREMENT PROCEDURES –

Part 3: Optical power variation induced by mechanical disturbance
in optical receptacles and transceiver interfaces



1 Scope
The purpose of this part of IEC 62150 is to specify the test requirements and procedures for
qualifying optical devices for sensitivity to coupled power variations induced by mechanical
disturbance at the optical ports of the device. It applies to active devices with optical receptacle
interfaces. In this edition, transceivers using small-form-factor connector cables (1,25 mm
ferrule) for single mode fibre are specified.
It has been found that some optical transceivers and receptacles are susceptible to fibre optic
cable induced stress when side forces are applied to the mated cable-connector assembly,
resulting in variations in the transmitted optical power. This part of IEC 62150 defines physical
stress tests to ensure that such optical connections (cable and receptacle) can continue to
function within specifications.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
IEC 61753 (all parts), Fibre optic interconnecting devices and
...