SIST EN 754-1:2008
(Main)Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery
This part of EN 754 specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy cold drawn rod/bar and tube for general engineering applications. It applies to products which are extruded and then cold drawn. It does not, however, apply to products delivered in coils, or to products which are rolled and then cold drawn, e.g. seam welded tubes.
Aluminium und Aluminiumlegierungen - Gezogene Stangen und Rohre - Teil 1: Technische Lieferbedingungen
Dieses Dokument legt die Technischen Lieferbedingungen für gezogene Stangen und Rohre aus Aluminium und Aluminiumlegierungen für allgemeine Anwendungen fest.
Es gilt für stranggepresste und dann kaltgezogene Erzeugnisse.
Dieses Dokument gilt nicht für:
- Schmiedevormaterial,
- stranggepresste Präzisionsprofile der Legierungen EN AW-6060 und EN AW-6063,
- Erzeugnisse, die aufgewickelt geliefert werden,
- Rohre in Ringen, die auf Länge geschnitten werden.
Aluminium et alliage d'aluminium - Barres et tubes étirés - Partie 1: Conditions techniques de contrôle et de livraison
Ce document spécifie les conditions techniques de contrôle et de livraison des barres et tubes étirés en aluminium et alliages d'aluminium a usage général.
Elle s'applique aux produits qui sont filés, puis étirés a froid.
Le document ne s'applique pas aux :
- produits forgés ;
- profilés de précision filés en alliage EN AW-6060 et EN AW-6063 ;
- produits livrés en couronne ;
- tubes en couronnes découpés a longueur.
Aluminij in aluminijeve zlitine - Hladno vlečene palice/drogovi in cevi - 1. del: Tehnični pogoji za pregled in dobavo
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 754-1:2008
01-maj-2008
1DGRPHãþD
SIST EN 754-1:1998
$OXPLQLMLQDOXPLQLMHYH]OLWLQH+ODGQRYOHþHQHSDOLFHGURJRYLLQFHYLGHO
7HKQLþQLSRJRML]DSUHJOHGLQGREDYR
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical
conditions for inspection and delivery
Aluminium und Aluminiumlegierungen - Gezogene Stangen und Rohre - Teil 1:
Technische Lieferbedingungen
Aluminium et alliage d'aluminium - Barres et tubes étirés - Partie 1: Conditions
techniques de contrôle et de livraison
Ta slovenski standard je istoveten z: EN 754-1:2008
ICS:
77.150.10
SIST EN 754-1:2008 en,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 754-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2008
ICS 77.150.10 Supersedes EN 754-1:1997
English Version
Aluminium and aluminium alloys - Cold drawn rod/bar and tube -
Part 1: Technical conditions for inspection and delivery
Aluminium et alliages d'aluminium - Barres et tubes étirés - Aluminium und Aluminiumlegierungen - Gezogene Stangen
Partie 1: Conditions techniques de contrôle et de livraison und Rohre - Teil 1: Technische Lieferbedingungen
This European Standard was approved by CEN on 10 February 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 754-1:2008: E
worldwide for CEN national Members.
---------------------- Page: 2 ----------------------
EN 754-1:2008 (E)
Contents Page
Foreword.3
1 Scope .5
2 Normative references .5
3 Terms and definitions .6
4 Ordering information.6
5 Requirements.8
5.1 Production and manufacturing processes .8
5.2 Quality control.8
5.3 Chemical composition limits.8
5.4 Mechanical properties.8
5.5 Freedom from surface defects .8
5.6 Tolerances on dimensions and form.8
5.7 Stress corrosion cracking resistance.9
5.8 Additional requirements .9
6 Test procedures.9
6.1 Sampling.9
6.2 Test methods.11
6.3 Re-tests.11
7 Inspection documents.12
8 Marking of products .12
9 Packaging .12
10 Arbitration.13
Annex A (normative) Location of test pieces .14
A.1 Round, square and hexagonal bar.14
A.2 Rectangular bar.15
A.3 Tube .15
Annex B (normative) Resistance to stress-corrosion cracking for alloy EN AW-7075 in tempers
T73, T7351, T73510 and T73511– Electrical conductivity .17
Bibliography .18
2
---------------------- Page: 3 ----------------------
EN 754-1:2008 (E)
Foreword
This document (EN 754-1:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and
aluminium alloys”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2008, and conflicting national standards shall be
withdrawn at the latest by September 2008.
This document supersedes EN 754-1:1997.
Within its programme of work, Technical committee CEN/TC 132 entrusted CEN/TC 132/WG 5 "Extruded and
drawn products" to revise EN 754-1:1997.
The following technical modifications have been introduced during the revision:
Clause 1: Scope is clarified with respect to what is not included
Clause 3: Definition of order document is included
Clause 4: The order document shall contain information about application especially for products to be
anodised
Subclauses 5.4 and 6.2.3: Provisions regarding Brinell hardness testing is included
Subclauses 5.7 and 6.2.6: Requirements to stress corrosion cracking resistance is included (from former
Annex A in Part 2)
Subclause 6.1.1: For samples for chemical analysis reference is made to EN 14361
Subclause 6.1.3.3: For shapes and dimensions of test pieces reference is made to EN 10002-1 (and
former Annex A is deleted)
Clause 7: For inspection documents reference is made to EN 10204
Annex B: Resistance to stress corrosion cracking – Electrical conductivity is added (taken from former
Part 2)
EN 754 comprises the following parts under the general title "Aluminium and aluminium alloys — Cold drawn
rod/bar and tube ":
Part 1: Technical conditions for inspection and delivery
Part 2: Mechanical properties
Part 3: Round bars, tolerances on dimensions and form
Part 4: Square bars, tolerances on dimensions and form
Part 5: Rectangular bars, tolerances on dimensions and form
Part 6: Hexagonal bars, tolerances on dimensions and form
3
---------------------- Page: 4 ----------------------
EN 754-1:2008 (E)
Part 7: Seamless tubes, tolerances on dimensions and form
Part 8: Porthole tubes, tolerances on dimensions and form
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardized
standards products under reasonable and not discriminatory conditions then this product shall be removed
from the corresponding standard.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
4
---------------------- Page: 5 ----------------------
EN 754-1:2008 (E)
1 Scope
This document specifies the technical conditions for inspection and delivery of aluminium and aluminium alloy
cold drawn rod/bar and tube for general engineering applications.
This document applies to products which are extruded and then cold drawn.
This document does not apply to:
forging stock (EN 603),
products delivered in coils (EN 13958),
coiled tubes cut to length (EN 13958).
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references only the edition cited applies. For undated references the latest edition of the referenced document
(including any amendments) applies.
EN 515, Aluminium and aluminium alloys — Wrought products — Temper designations
EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3:
Chemical composition and form of products
EN 754-2, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 2: Mechanical properties
EN 754-3, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 3: Round bars, tolerances
on dimensions and form
EN 754-4, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 4: Square bars, tolerances
on dimensions and form
EN 754-5, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 5: Rectangular bars,
tolerances on dimensions and form
EN 754-6, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 6: Hexagonal bars,
tolerances on dimensions and form
EN 754-7, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 7: Seamless tubes,
tolerances on dimensions and form
EN 754-8, Aluminium and aluminium alloys — Cold drawn rod/bar and tube — Part 8: Porthole tubes,
tolerances on dimensions and form
EN 2004-1, Aerospace series — Test methods for aluminium and aluminium alloy products — Part 1:
Determination of electrical conductivity of wrought aluminium alloys
EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test at ambient temperature
EN 10204, Metallic products — Types of inspection documents
EN 12258-1:1998, Aluminium and aluminium alloys — Terms and definitions — Part 1: General terms
EN 14242, Aluminium and aluminium alloys — Chemical analysis — Inductively coupled plasma optical
emission spectral analysis
5
---------------------- Page: 6 ----------------------
EN 754-1:2008 (E)
EN 14361, Aluminium and aluminium alloys — Chemical analysis — Sampling from metal melts
EN ISO 6506-1, Metallic materials — Brinell hardness test — Part 1: Test method (ISO 6506-1:2005)
ISO 9591, Corrosion of aluminium alloys — Determination of resistance to stress corrosion cracking
ASTM G47, Standard Test Method for Determining Susceptibility to Stress-Corrosion Cracking of 2XXX and
7XXX Aluminium Alloy Products
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 12258-1:1998 and the following
apply.
3.1
order document
document or set of documents agreed between supplier and purchaser at the time of ordering
4 Ordering information
The order document shall contain the following:
a) form and type of product:
form of the product (cold drawn rod/bar or tube). If tube, whether seamless or porthole/bridge,
reference to EN 573-3 for chemical composition limits,
reference to EN 515 for temper designation,
purchaser application, in particular whether subsequent anodising is intended. This shall be clearly
stated on the order document;
b) reference to EN 754-2 for mechanical property limits;
c) a reference to this document (EN 754-1);
d) dimensions and shape of the product:
1) round tube:
length,
and only two of the following dimensions:
outside diameter,
inside diameter,
wall thickness;
2) round bar:
diameter,
length;
6
---------------------- Page: 7 ----------------------
EN 754-1:2008 (E)
3) square and hexagonal bar:
width across flats,
length;
4) rectangular bar:
width,
thickness,
length;
5) all other cases:
drawing of cross section,
length;
e) tolerances on dimensions and form, with reference to the appropriate European Standard and/or a
drawing;
f) quantity:
mass,
number of pieces,
total length,
tolerance on quantity;
g) any requirements for inspection documents;
h) any special requirements agreed between supplier and purchaser:
marking of products,
reference to drawings, part numbers, etc,
additional or special testing, e.g. stress corrosion testing,
surface finish requirements,
surface protection,
packaging,
inspection prior to delivery,
use of A value instead of A value for elongation;
50mm
i) for products intended to be anodised by the purchaser, the order document shall also contain the
information about the intended particular surface treatment with reference to the relevant European
Standard.
7
---------------------- Page: 8 ----------------------
EN 754-1:2008 (E)
5 Requirements
5.1 Production and manufacturing processes
Unless otherwise specified in the order document, the production and manufacturing processes shall be left to
the discretion of the manufacturer. Unless it is explicitly stated in the order document, no obligation shall be
placed on the manufacturer to use the same processes for subsequent or similar orders.
5.2 Quality control
The supplier shall be responsible for the performance of all inspection and tests required by the relevant
European Standard and/or the particular specification prior to shipment of the product. If the purchaser wishes
to inspect the product at the manufacturer's works, he shall notify the supplier at the time of placing the order.
5.3 Chemical composition limits
The chemical composition limits shall be in conformity with the requirements specified in EN 573-3.
If the purchaser requires closer limits for elements than those specified in the above standard, these limits shall
be according to an agreement between supplier and purchaser and stated in the order document.
5.4 Mechanical properties
The mechanical properties shall be in conformity with those specified in EN 754-2 or those agreed between
supplier and purchaser and stated in the order document.
Typical Brinell hardness values are given in EN 754-2, but they are not binding for acceptance purposes.
However, a Brinell hardness value may be agreed upon for acceptance testing.
5.5 Freedom from surface defects
The surface shall be free from defects pr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.