SIST EN 3162:2007

Aerospace series - Steel FE-PM3801 (X5CrNiCu17-4) - Air melted, solution treated and precipitation treated, sheet and strip a <= 6 mm, Rm >= 930 MPa

This standard specifies the requirements relating to:
Steel FE-PM3801 (X5CrNiCu17-4) - Air melted, solution treated and precipitation treated, sheet and strip a 6 mm, Rm 930 MPa
for aerospace applications.

Luft- und Raumfahrt - Stahl FE-PM3801 (X5CrNiCu17-4) - Lufterschmolzen, lösungsgeglüht und ausgelagert, Bleche und Bänder a <= 6 mm, Rm >= 930 MPa

Série aérospatiale - Acier FE-PM3801 (X5CrNiCu17-4) - Élaboré a l'air, mis en solution et vieilli, tôles et bandes a <= 6 mm, Rm >= 930 MPa

Aeronavtika - Jeklo FE-PM3801 (X5CrNiCu17-4) - Pločevine in trakovi <= 6 mm, Rm >= 930 MPa, taljeni, žarjeni v topilu in utrjeni

General Information

• Status: Published
• Publication Date: 01-Oct-2007
• ICS: 49.025.10 - Steels
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 03-Sep-2007
• Due Date: 08-Nov-2007
• Completion Date: 02-Oct-2007
• Ref Project: EN 3162:2007 - Aerospace series - Steel FE-PM3801 (X5CrNiCu17-4) - Air melted, solution treated and precipitation treated, sheet and strip a ≤ 6 mm, Rm ≥ 930 MPa

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Steel FE-PM3801 (X5CrNiCu17-4) - Air melted, solution treated and precipitation treated, sheet and strip a <= 6 mm, Rm >= 930 MPaSérie aérospatiale - Acier FE-PM3801 (X5CrNiCu17-4) - Élaboré a l'air, mis en solution et vieilli, tôles et bandes a <= 6 mm, Rm >= 930 MPaLuft- und Raumfahrt - Stahl FE-PM3801 (X5CrNiCu17-4) - Lufterschmolzen, lösungsgeglüht und ausgelagert, Bleche und Bänder a <= 6 mm, Rm >= 930 MPaTa slovenski standard je istoveten z:EN 3162:2007SIST EN 3162:2007en49.025.10JeklaSteelsICS:SLOVENSKI
STANDARDSIST EN 3162:200701-november-2007







EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3162
August 2007 ICS 49.025.10 English Version
Aerospace series - Steel FE-PM3801 (X5CrNiCu17-4) - Air melted, solution treated and precipitation treated, sheet and strip a ≤ 6 mm, Rm ≥ 930 MPa
Série aérospatiale - Acier FE-PM3801 (X5CrNiCu17-4) - Élaboré à l'air, mis en solution et vieilli, tôles et bandes a ≤6 mm, Rm ≥ 930 MPa
Luft- und Raumfahrt - Stahl FE-PM3801 (X5CrNiCu17-4) - Lufterschmolzen, lösungsgeglüht und ausgelagert, Bleche und Bänder a ≤ 6 mm, Rm ≥ 930 MPa This European Standard was approved by CEN on 24 February 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3162:2007: E



EN 3162:2007 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.4 2 Normative references.4



EN 3162:2007 (E) 3 Foreword This document (EN 3162:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2008, and conflicting national standards shall be withdrawn at the latest by February 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall
...