SIST EN ISO 10352:2011
(Main)Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area (ISO 10352:2010)
Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass per unit area (ISO 10352:2010)
This International Standard specifies a method for the determination of the mass per unit area of sheet moulding compound and preimpregnated unidirectional sheet, tape, fabric and mats. Unless stated to the contrary in the relevant material specification, this International Standard is applicable to prepregs in which any type of reinforcement (aramid, carbon, glass, etc.) and any type of matrix (thermosetting or thermoplastic) has been used.
Faserverstärkte Kunststoffe - Formmassen und Prepregs - Bestimmung des Flächengewichtes (ISO 10352:2010)
Diese Internationale Norm legt ein Verfahren für die Bestimmung des Flächengewichtes von Harzmatten
(SMC) und vorimprägnierten unidirektionalen Bahnen, Bändern, Geweben und Matten fest.
Sofern in den jeweiligen Materialspezifikationen nichts Gegenteiliges festgelegt ist, gilt diese Norm für
Prepregs unabhängig davon, welche Art der Verstärkung (Aramid, Carbon, Glas usw.) oder welcher Typ der
Matrix (wärmehärtend oder thermoplastisch) verwendet ist.
Plastiques renforcés - Préimprégnés - Détermination de la masse surfacique (ISO 10352:2010)
L'ISO 10352:2010 spécifie une méthode de détermination de la masse surfacique des mélanges à mouler en feuilles et des feuilles avec renforts unidirectionnels, rubans, tissus et mats préimprégnés.
Sauf indication contraire dans la spécification du matériau concerné, elle est applicable aux préimprégnés, quelle que soit la nature du renfort (aramide, carbone, verre, etc.) et du système de résine (thermodurcissable ou thermoplastique) ayant été utilisés.
Z vlakni ojačeni polimerni materiali - Zmesi za oblikovanje in preimpregniranje - Določevanje mase na enoto površine (ISO 10352:2010)
Ta mednarodni standard opredeljuje metodo za določevanje mase na enoto površine zmesi za oblikovanje v plasteh in preimpregniranih enosmernih plasti, trakov, blaga in matov. Razen če je navedeno v nasprotju z ustreznimi specifikacijami za material, ta mednarodni standard velja za materiale za preimpregniranje, pri katerih je bil uporabljen kateri koli tip ojačitve (aramidna, karbonska, steklena itd.) in kateri koli tip matriksa (termoreaktivni ali plastomerni).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 10352:2011
01-november-2011
1DGRPHãþD
SIST EN ISO 10352:1999
=YODNQLRMDþHQLSROLPHUQLPDWHULDOL=PHVL]DREOLNRYDQMHLQSUHLPSUHJQLUDQMH
'RORþHYDQMHPDVHQDHQRWRSRYUãLQH ,62
Fibre-reinforced plastics - Moulding compounds and prepregs - Determination of mass
per unit area (ISO 10352:2010)
Faserverstärkte Kunststoffe - Formmassen und Prepregs - Bestimmung des
Flächengewichtes (ISO 10352:2010)
Plastiques renforcés - Préimprégnés - Détermination de la masse surfacique (ISO
10352:2010)
Ta slovenski standard je istoveten z: EN ISO 10352:2010
ICS:
83.120 2MDþDQLSROLPHUL Reinforced plastics
SIST EN ISO 10352:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10352:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 10352:2011
EUROPEAN STANDARD
EN ISO 10352
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2010
ICS 83.120 Supersedes EN ISO 10352:1997
English Version
Fibre-reinforced plastics - Moulding compounds and prepregs -
Determination of mass per unit area (ISO 10352:2010)
Plastiques renforcés - Mélanges à mouler et préimprégnés Faserverstärkte Kunststoffe - Formmassen und Prepregs -
- Détermination de la masse surfacique (ISO 10352:2010) Bestimmung des Flächengewichtes (ISO 10352:2010)
This European Standard was approved by CEN on 10 December 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10352:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 10352:2011
EN ISO 10352:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 10352:2011
EN ISO 10352:2010 (E)
Foreword
This document (EN ISO 10352:2010) has been prepared by Technical Committee ISO/TC 61 “Plastics” in
collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2011, and conflicting national standards shall be withdrawn at
the latest by June 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10352:1997.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10352:2010 has been approved by CEN as a EN ISO 10352:2010 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 10352:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 10352:2011
INTERNATIONAL ISO
STANDARD 10352
Third edition
2010-12-15
Fibre-reinforced plastics — Moulding
compounds and prepregs —
Determination of mass per unit area
Plastiques renforcés de fibres — Mélanges à mouler et
préimprégnés — Détermination de la masse surfacique
Reference number
ISO 10352:2010(E)
©
ISO 2010
---------------------- Page: 7 ----------------------
SIST EN ISO 10352:2011
ISO 10352:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 10352:2011
ISO 10352:2010(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Principle.1
5 Apparatus.2
6 Conditioning and testing .2
6.1 Conditioning .2
6.1.1 Materials for which no conditioning is required .2
6.1.2 Conditioning of material stored at ambient temperature.2
6.1.3 Conditioning of material stored at below ambient temperature.2
6.2 Testing.2
6.2.1 Test atmosphere.2
6.2.2 Time interval between conditioning and testing.3
7 Test specimens.3
7.1 Shape and dimensions .3
7.2 Number .4
7.3 Preparation.4
8 Procedure.4
8.1 Materials made without using a solvent .4
8.2 Materials made using a solvent .4
9 Expression of results.5
9.1 Samples made without using a solvent .5
9.2 Samples made using a solvent .5
10 Precision.5
11 Test report.6
© ISO 2010 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 10352:2011
ISO 10352:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10352 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 13, Composites
and reinforcement fibres.
This third edition cancels and replaces the second edition (ISO 10352:1997), which has been technically
revised to make a distinction between materials which have been manufactured using a solvent and those
which have been manufactured without using a solvent, a different variant of the procedure being specified for
each.
iv © ISO 2010 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 10352:2011
INTERNATIONAL STANDARD ISO 10352:2010(E)
Fibre-reinforced plastics — Moulding compounds and
prepregs — Determination of mass per unit area
1 Scope
This International Standard specifies a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.