SIST EN 1870-17:2012
(Main)Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws)
Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws)
This European Standard specifies all significant hazards, hazardous situation and events as listed in Clause 4, relevant to stationary and displaceable manual horizontal cutting cross-cut circular sawing machines with one saw unit (manual radial arm saws), hereinafter referred to as “machines”, designed to cut solid wood, chipboard, fibreboard, plywood and also these materials if they are covered with plastic edging and/or plastic laminates, when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse.
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 17: Handbetätigte waagrecht schneidende Auslegerkreissägemaschinen mit einem Sägeaggregat (handbetätigte Radialsägen)
Dieses Dokument spezifiziert alle in Abschnitt 4 aufgeführten signifikanten Gefährdungen, Gefährdungs-situationen und Gefährdungsereignisse fest, die auf stationäre und verschiebbare handbetätigte waagerecht schneidende Auslegerkreissägemaschinen mit einem Sägeaggregat (handbetätigte Radialsägen) zutreffen — im Folgenden als „Maschinen“ bezeichnet —, die konstruiert sind zum Schneiden von Massivholz, Spanplatten, Faserplatten oder Sperrholz sowie diesen Werkstoffen, wenn sie mit Kunststoffkanten versehen sind und/oder Beschichtungen aus Kunststoff haben, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers einschließlich vernünftigerweise vorhersehbarem Fehlverhalten verwendet werden.
ANMERKUNG 1 Hinsichtlich der Definitionen für stationäre und verschiebbare Maschinen, siehe 3.2.3 und 3.2.4.
Dieses Dokument gilt nicht für:
a)
Maschinen, die auf einem Gestell oder auf einen Tisch, der einem Gestell ähnlich ist, aufgesetzt sind und die vorgesehen sind, während des Betriebs stationär verwendet zu werden, und die von einer Person von Hand angehoben werden können. Das Gestell kann auch ein fester Teil der Maschine sein, wenn es aus scharnierbefestigten Füßen besteht, die heruntergeklappt werden können;
ANMERKUNG 2 Transportable motorbetriebene Elektrowerkzeuge sind in EN 61029-1:2009 zusammen mit EN 61029-2-2:2009 behandelt.
b)
Maschinen, die mit hydraulischen Maschinenantrieben (z. B. hydraulische Werkstückspannung) ausge-rüstet sind;
c)
Maschinen, die mit kraftbetriebener Werkstückpositionierung ausgerüstet sind;
d)
Maschinen, die entweder zum Längsschneiden, Fräsen (einschließlich Fälzen und Nuten), Schleifen und/oder Bohren vorgesehen sind;
e)
Maschinen, die mit mehr als einer Sägespindeldrehzahl ausgerüstet sind.
ANMERKUNG 3 Es wird bei der nächsten Überarbeitung beraten, eine Norm für Maschinen zu erarbeiten, die zum Längsschneiden und
Sécurité des machines pour le travail du bois - Machines à scies circulaires - Partie 17: Tronçonneuses manuelles à coupe horizontale avec une unité de sciage (scies circulaires radiales manuelles)
Le présent document traite des phénomènes dangereux, situations et événements dangereux significatifs, tels
qu’énumérés à l’Article 4, applicables aux tronçonneuses manuelles à coupe horizontale fixes et
transportables avec une unité de sciage (scies circulaires radiales manuelles), désignées ci-après sous le
terme « machines ». Celles-ci sont conçues pour usiner du bois, des panneaux de fibres ou de particules, de
contreplaqué ainsi que ces matériaux lorsque leurs surfaces ou leurs chants sont recouverts de matière
plastique et/ou d’un stratifié de plastique, lorsqu’elles sont utilisées normalement et dans les conditions
prévues par le fabricant, y compris une mauvaise utilisation raisonnablement prévisible.
NOTE 1 Pour la définition de machine fixe et de machine transportable, voir 3.2.3 et 3.2.4.
Le présent document n'est pas applicable aux machines :
a) montées sur un bâti ou une table similaire à un bâti, conçues pour réaliser un travail à poste fixe
capables d’être soulevées à la main par une personne.L'établi peut également être une pièce intégrée à
la machine s'il consiste en pieds articulés qui peuvent être dépliés ;
NOTE 2 Les machines à démarrage électrique transportables sont traités dans les EN 61029-1:2009 et
EN 61029-2-2:2009.
b) équipées d’actionneurs mécanisés hydrauliques (par exemple de bridage de pièce hydraulique);
c) équipées de dispositifs de positionnement de pièce mécanisés ;
d) équipées de dispositifs de délignage, d’usinage (y compris de tranchage et de rainurage), de ponçage
et/ou de perçage ;
e) équipées de plus d'une vitesse de broche de scie.
NOTE 3 Une norme traitant des machines qui peuvent être utilisées pour le délignage et le toupillage sera prise en
compte lors de la prochaine révision.
Varnost lesnoobdelovalnih strojev - Krožne žage - 17. del: Ročne horizontalne krožne žage za prečni rez z eno rezalno enoto (ročne radialne žage)
Ta evropski standard določa vsa večja tveganja, nevarne razmere in dogodke iz točke 4, ki se nanašajo na stacionarne in premestljive ročne horizontalne krožne žage za prečni rez z eno rezalno enoto (ročne radialne žage), v nadaljnjem besedilu »stroji«, ki so namenjene za rezanje polnega lesa, ivernih plošč, vlaknenih plošč, vezanih plošč in teh materialov, če so prekriti s plastičnimi robovi in/ali plastičnim laminatom, kadar se uporabljajo v skladu z namembnostjo in pod pogoji, ki jih predvidi proizvajalec, vključno z razumno predvideno nepravilno uporabo.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.KRUL]RQWDOQHHSicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 17: Handbetätigte waagrecht schneidende Auslegerkreissägemaschinen mit einem Sägeaggregat (handbetätigte Radialsägen)Sécurité des machines pour le travail du bois - Machines à scies circulaires - Partie 17: Tronçonneuses manuelles à coupe horizontale avec une unité de sciage (scies circulaires radiales manuelles)Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws)79.120.10Lesnoobdelovalni strojiWoodworking machines25.080.60Strojne žageSawing machinesICS:Ta slovenski standard je istoveten z:EN 1870-17:2012SIST EN 1870-17:2012en,fr,de01-december-2012SIST EN 1870-17:2012SLOVENSKI
STANDARDSIST EN 1870-17:2007+A2:20091DGRPHãþD
SIST EN 1870-17:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1870-17
October 2012 ICS 79.120.10 Supersedes EN 1870-17:2007+A2:2009English Version
Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (radial arm saws)
Sécurité des machines pour le travail du bois - Machines à scies circulaires - Partie 17: Tronçonneuses manuelles à coupe horizontale avec une unité de sciage (scies circulaires radiales manuelles)
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 17: Handbetätigte waagrecht schneidende Auslegerkreissägemaschinen mit einem Sägeaggregat (handbetätigte Radialsägen) This European Standard was approved by CEN on 4 August 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1870-17:2012: ESIST EN 1870-17:2012
EN 1870-17:2012 (E) 2 Contents Page Foreword .4Introduction .61 Scope .72 Normative references .73 Terms and definitions . 103.1 General . 103.2 Definitions . 104 List of significant hazards . 125 Safety requirements and/or measures . 155.1 General . 155.2 Controls . 155.2.1 Safety and reliability of control systems . 155.2.2 Position of controls . 165.2.3 Starting . 165.2.4 Normal stopping . 175.2.5 Failure of the power supply . 175.3 Protection against mechanical hazards . 175.3.1 Stability . 175.3.2 Risk of break-up during operation . 185.3.3 Tool holder and tool design . 185.3.4 Braking . 215.3.5 Workpiece supports and guides . 225.3.6 Prevention of access to moving parts . 235.3.7 Clamping devices . 275.4 Protection against non-mechanical hazards . 285.4.1 Fire . 285.4.2 Noise . 285.4.3 Emission of chips and dust . 295.4.4 Electricity . 305.4.5 Ergonomics and handling . 315.4.6 Pneumatics . 315.4.7 Electromagnetic compatibility . 315.4.8 Laser . 325.4.9 Static electricity . 325.4.10 Errors of fitting . 325.4.11 Supply disconnection (Isolation) . 325.4.12 Maintenance . 336 Information for use . 336.1 General . 336.2 Marking . 336.3 Instruction handbook . 34Annex A (normative)
Stability test for displaceable machines . 37Annex B (normative)
Saw spindle dimensional tolerances . 38Annex C (normative)
Impact test method for guards . 39C.1 General . 39C.2 Test method . 39C.2.1 Preliminary remarks . 39SIST EN 1870-17:2012
EN 1870-17:2012 (E) 3 C.2.2 Testing equipment . 39C.2.3 Projectile for guards . 39C.2.4 Sampling. 39C.2.5 Test procedure . 39C.3 Results . 40C.4 Assessment . 40C.5 Test report . 40C.6 Test equipment for impact test . 40Annex D (normative)
Brake tests . 42D.1 Conditions for all tests . 42D.2 Tests . 42D.2.1 Un-braked run-down time . 42D.2.2 Braked run-down time . 42Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC . 43Bibliography . 46 SIST EN 1870-17:2012
EN 1870-17:2012 (E) 4 Foreword This document (EN 1870-17:2012) has been prepared by Technical Committee CEN/TC 142 “Woodworking machines - Safety”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2013, and conflicting national standards shall be withdrawn at the latest by April 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1870-17:2007+A2:2009. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of the Machinery Directive. For relationship with the Machinery Directive 2006/42/EC, see informative Annex ZA, which is an integral part of this document. The main modification to the 2009 edition relates to the introduction of performance levels (PL). Organisations contributing to the preparation of this European Standard include European Committee of Woodworking Machinery Manufacturers Association "EUMABOIS. EN 1870, Safety of woodworking machines — Circular sawing machines, consists of the following parts: Part 1: Circular saw benches (with and without sliding table), dimension saws and building site saws; Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches; Part 4: Multi-blade rip sawing machines with manual loading and/or unloading; Part 5: Circular sawbenches/up-cutting cross-cut sawing machines; Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading; Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading; Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading; Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading; Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines; Part 11: Semi-automatic and automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws); Part 12: Pendulum cross-cut sawing machines; SIST EN 1870-17:2012
EN 1870-17:2012 (E) 5 Part 13: Horizontal beam panel sawing machines; Part 14: Vertical panel sawing machines; Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading; Part 16: Double mitre sawing machines for V-cutting; Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (radial arm saws); Part 18: Dimension saws (at Enquiry stage at the time of publication of the present document); Part 19: Circular saw benches (with and without sliding table) and building site saws (at Enquiry stage at the time of publication of the present document). The European Standards produced by CEN/TC 142 are particular to woodworking machines and complement the relevant A and B standards on the subject of general safety (see Introduction of EN ISO 12100:2010 for a description of A, B and C standards). According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 1870-17:2012
EN 1870-17:2012 (E) 6 Introduction This document has been prepared to be a harmonised standard to provide one means of conforming to the essential safety requirements of the Machinery Directive, and associated EFTA regulations. This document is a type C standard as stated in EN ISO 12100:2010. The machinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of other standards, for machines that have been designed and built in accordance with the requirements of the provisions of this type C standard. The requirements of this document are directed to manufacturers and their authorised representatives of manual horizontal cutting cross-cut circular sawing machines with one saw unit (manual radial arm saws). It is also useful for designers. This document also includes provisions and examples of information to be provided by the manufacturer to the user. Common requirements for tooling are given in EN 847-1:2005+A1:2007.
SIST EN 1870-17:2012
EN 1870-17:2012 (E) 7 1 Scope This European Standard specifies all significant hazards, hazardous situation and events as listed in Clause 4, relevant to stationary and displaceable manual horizontal cutting cross-cut circular sawing machines with one saw unit (manual radial arm saws), hereinafter referred to as “machines”, designed to cut solid wood, chipboard, fibreboard, plywood and also these materials if they are covered with plastic edging and/or plastic laminates, when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. NOTE 1 For the definition of stationary and displaceable machine, see 3.2.3 and 3.2.4. The requirements of this document apply to all machines whatever their method of control e.g. electromechanical and/or electronic. This document does not apply to: a) machines set up on a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand; the bench can also be an integrated part of the machine if it consists of hinged legs which can be extended down; NOTE 2 Transportable motor-operated electrical tools are dealt with in EN 61029-1:2009 together with
IEC 61029-2-2:1993. b) machines fitted with hydraulically powered machine actuators; c) machines fitted with powered work-piece positioning; d) machines fitted with the facility for either ripping, milling (including trenching and grooving), sanding and/or drilling; e) machines equipped with more than one saw spindle speed; NOTE 3 A standard to cover machines that can be used for ripping and moulding will be considered at the next revision. NOTE 4 Semi-automatic and automatic horizontal cutting cross-cut circular sawing machines with one saw unit (radial arm saws) are dealt with in EN 1870-11:2003+A1:2009. f) machines with integrated feed. This document is not applicable to manual horizontal cutting cross-cut circular sawing machines with one saw unit (manual radial arm saws) which are manufactured before the date of its publication as EN. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 614-1:2006+A1:2009, Safety of machinery — Ergonomic design principles — Part 1: Terminology and general principles EN 614-2:2000+A1:2008, Safety of machinery — Ergonomic design principles — Part 2: Interactions between the design of machinery and work tasks EN 847-1:2005+A1:2007, Tools for woodworking — Safety requirements — Part 1: Milling tools, circular saw blades SIST EN 1870-17:2012
EN 1870-17:2012 (E) 8 EN 894-1:1997+A1:2008, Safety of machinery — Ergonomics requirements for the design of displays and control actuators — Part 1: General principles for human interactions with displays and control actuators EN 894-2:1997+A1:2008, Safety of machinery — Ergonomics requirements for the design of displays and control actuators — Part 2: Displays EN 894-3:2000+A1:2008, Safety of machinery — Ergonomics requirements for the design of displays and control actuators — Part 3: Control actuators EN 1005-1:2001+A1:2008, Safety of machinery — Human physical performance — Part 1: Terms and definitions EN 1005-2:2003+A1:2008, Safety of machinery — Human physical performance — Part 2: Manual handling of machinery and component parts of machinery EN 1005-3:2002+A1:2008, Safety of machinery — Human physical performance — Part 3: Recommended force limits for machinery operation EN 1005-4:2005+A1:2008, Safety of machinery — Human physical performance — Part 4: Evaluation of working postures and movements in relation to machinery EN 1037:1995+A1:2008, Safety of machinery — Prevention of unexpected start-up EN 1088:1995+A2:2008, Safety of machinery — Interlocking devices associated with guards — Principles for design and selection EN 50370-1:2005, Electromagnetic compatibility (EMC) — Product family standard for machine tools — Part 1: Emission EN 50370-2:2003, Electromagnetic compatibility (EMC) — Product family standard for machine tools — Part 2: Immunity EN 60204-1:2006, Safety of machinery — Electrical equipment of machines — Part 1: General requirements (IEC 60204-1:2005, modified) EN 60439-1:1999,1) Low-voltage switchgear and controlgear assemblies — Part 1: Type-tested and partially type-tested assemblies (IEC 60439-1:1999) EN 60529:1991,2) Degrees of protection provided by enclosures (IP Code) (IEC 60529:1989) EN 60825-1:2007, Safety of laser products — Part 1: Equipment classification and requirements (IEC 60825-1:2007) EN 61310-1:2008, Safety of machinery — Indication, marking and actuation — Part 1: Requirements for visual, auditory and tactile signals (IEC 61310-1:2007) EN 61800-5-2:2007, Adjustable speed electrical power drive systems — Part 5-2: Safety requirements — Functional (IEC 61800-5-2:2007) EN ISO 3743-1:2010, Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering methods for small moveable sources in reverberant fields — Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)
1) EN 60439-1:1999 is amended by EN 60439-1:1999/A1:2004, based on IEC 60439-1:1999/A1:2004. 2) EN 60529:1991 is amended by EN 60529:1991/A1:2000, based on IEC 60529:1989/A1:1999. SIST EN 1870-17:2012
EN 1870-17:2012 (E) 9 EN ISO 3743-2:2009, Acoustics — Determination of sound power levels of noise sources using sound pressure — Engineering methods for small, movable sources in reverberant fields — Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994) EN ISO 3744:2010, Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Engineering method in an essentially free field over a reflecting plane (ISO 3744:2010) EN ISO 3745:2009,3) Acoustics — Determination of sound power levels of noise sources using sound pressure — Precision methods for anechoic and semi-anechoic rooms (ISO 3745:2003) EN ISO 3746:2010, Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pressure — Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010) EN ISO 4414:2010, Pneumatic fluid power — General rules and safety requirements for systems and their components (ISO 4414:2010) EN ISO 4871:2009, Acoustics — Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996) EN ISO 9614-1:2009, Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points (ISO 9614-1:1993) EN ISO 11202:2010, Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010) EN ISO 11204:2010, Acoustics — Noise emitted by machinery and equipment — Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010) EN ISO 11688-1:2009, Acoustics — Recommended practice for the design of low-noise machinery and equipment — Part 1: Planning (ISO/TR 11688-1:1995) EN ISO 12100:2010, Safety of machinery — General principles for design — Risk assessment and risk reduction (ISO 12100:2010) EN ISO 13849-1:2008, Safety of machinery — Safety-related parts of controls systems — Part 1: General principles for design (ISO 13849-1:2006) EN ISO 13857:2008, Safety of machinery — Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008) ISO 7960:1995, Airborne noise emitted by machine tools — Operating conditions for woodworking machines HD 22.4 S4:2004,4) Cables of rated voltages up to and including 450/750 V and having cross-linked insulation — Part 4: Cords and flexible cables
3) EN ISO 3745:2009 is superseded by EN ISO 3745:2012. 4) HD 22.4 S4:2004 is superseded by EN 50525-2-21:2011. SIST EN 1870-17:2012
EN 1870-17:2012 (E) 10 3 Terms and definitions 3.1 General For the purposes of this document, the terms and definitions given in EN ISO 12100:2010 and the following apply. 3.2 Definitions 3.2.1 cross-cutting operation of cutting across the longitudinal workpiece dimension 3.2.2 manual horizontal cutting cross-cut circular sawing machine with one saw unit (manual radial arm saw) machine where the saw unit has hand feed and is moved horizontally forward along an arm in a straight line through the workpiece during the cut and then back to its initial/rest position
Note 1 to entry: See Figures 1 and 2. Note 2 to entry: The arm can rotate around a vertical axis (pivoting) in a horizontal plane and the saw unit can rotate about a horizontal axis (canting) parallel to the arm. The workpiece is manually positioned on and removed from the workpiece support.
NOTE The saw blade is not in the rest position. Figure 1 — Example 1 of a manual horizontal cutting cross-cut circular sawing machine with one saw unit (manual radial arm saw) SIST EN 1870-17:2012
EN 1870-17:2012 (E) 11
Figure 2 — Example 2 of a manual horizontal cutting cross-cut circular sawing machine with one saw unit (manual radial arm saw) 3.2.3 stationary machine machine designed to be located on or fixed to the floor or other parts of the structure of the premises and to be stationary during use 3.2.4 displaceable machine machine which is located on the floor, stationary during use and equipped with a device, normally wheels, which allow it to be moved between locations 3.2.5 hand feed of the saw unit manual movement of the saw unit incorporating the saw blade along the forward arm of the machine in direction of the feed movement 3.2.6 machine actuator power mechanism used to effect motion of the saw blade 3.2.7 cutting area of the saw blade area of the saw blade where it can be involved in the cutting process 3.2.8 non-cutting area of the saw blade area of the saw blade where it is not involved in the cutting process 3.2.9 cutting area of a radial arm saw area formed by the maximum left and right pivoting and canting position at maximum stroke capacity of the saw blade with the maximum saw blade diameter the machine is designed for SIST EN 1870-17:2012
EN 1870-17:2012 (E) 12 3.2.10 un-braked run-down time time elapsed from the actuation of the stop control device up to spindle standstill with deactivated brake
3.2.11 braked run-down time time elapsed from the actuation of the stop control device up to spindle standstill with activated brake
3.2.12 information from the supplier statements, sales literature, leaflets or other documents where a manufacturer (supplier) declares either the characteristics or the compliance of the material or product to a relevant standard 3.2.13 performance level
PL discrete level used to specify the ability of safety-related parts of control systems to perform a safety function under foreseeable conditions [SOURCE: EN ISO 13849-1:2008, 3.1.23] 4 List of significant hazards This clause contains all significant hazards, hazardous situations and events (see EN ISO 12100:2010), identified by risk assessment as significant for the machines as defined in the scope and which require action to eliminate or reduce the risk by defining safety requirements and/or measures or by reference to relevant standards. These hazards are listed in Table 1. SIST EN 1870-17:2012
EN 1870-17:2012 (E) 13 Table 1 — List of significant hazards No Hazards, hazardous situations and hazardous events ENISO12100:2010 Relevant clause of this document 1 Mechanical hazards related to: - machine parts or workpieces:
a) shape; 6.2.2.1, 6.2.2.2, 6.3 5.3.3, 5.3.5, 5.3.7, 5.4.5
b) relative location; 5.2.2, 5.3.3, 5.3.5, 5.3.6, 5.3.7, 5.4.3, 5.4.5
d) mass and velocity (kinetic energy of elements in controlled or
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.