SIST EN 13448:2002
(Main)Agricultural and forestry machinery - Inter-row mowing units - Safety
Agricultural and forestry machinery - Inter-row mowing units - Safety
This European Standard specifies the safety requirements and test methods for the design and construction of inter-row mowing units with vertical spindles mounted on grass cutting machines such as flail mowers, used in agriculture, forestry and landscaping to cut the grass in the area between two successive obstruction.
It describes methods for elimination or reduction of risks arising from their use.
In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
This standard is not applicable to rotary mowers and flail-mowers which are covered by EN 745.
Environmental aspects have not been considered in this standard.
This European Standard is not applicable to inter-row mowing units which are manufactured before the date of publication of this document by CEN.
Land- und forstwirtschaftliche Maschinen - Zwischenreihenmäher - Sicherheit
Diese Europäische Norm enthält sicherheitstechnische Anforderungen und deren Überprüfung für die Gestaltung und Konstruktion von Zwischenreihenmähern mit senkrechten Spindeln, die an Grasmähmaschinen wie Schlegelmähern angebaut sind. Sie werden in der Land- und Forstwirtschaft und in der Landschaftspflege verwendet zum Grasschneiden im Bereich von zwei aufeinander folgenden Hindernissen.
Sie beschreibt Maßnahmen zur Vermeidung oder Verminderung der sich aus dem Gebrauch ergebenden Gefährdungen.
Außerdem legt sie fest, welche Hinweise zum sicheren Arbeiten vom Hersteller zu geben sind.
Diese Norm gilt nicht für Kreiselmähwerke und Schlegelmäher, die in EN 745 behandelt werden.
Die Umweltaspekte wurden in dieser Norm nicht in Betracht gezogen.
Diese Europäische Norm gilt für Zwischenreihenmäher, die hergestellt wurden vor der Veröffentlichung dieses Dokumentes durch CEN.
Matériel agricole et forestier - Faucheuses interlignes - Sécurité
La présente Norme européenne détermine les prescriptions de sécurité et les vérifications pour la conception et la construction des faucheuses interlignes a axes verticaux montées sur des machines pour couper l'herbe telles que des faucheuses-broyeuses, utilisées en agriculture, en sylviculture et pour l'entretien des espaces verts pour couper l'herbe dans la zone comprise entre deux obstacles successifs.
Elle décrit les méthodes pour l'élimination et la réduction des risques inhérents a leur utilisation.
En outre, elle spécifie le type d'informations que le fabricant doit donner sur les pratiques d'utilisation sure.
Cette norme n'est pas applicable aux faucheuses rotatives ni aux faucheuses-broyeuses traitées dans l'EN 745.
Les aspects liés a l'environnement n'ont pas été pris en compte dans cette norme.
La présente Norme européenne n'est pas applicable aux faucheuses interlignes qui ont été fabriquées avant la date de publication de ce document par le CEN.
Kmetijski in gozdarski stroji - Medvrstne zastiralne kosilnice - Varnost
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13448:2002
01-november-2002
Kmetijski in gozdarski stroji - Medvrstne zastiralne kosilnice - Varnost
Agricultural and forestry machinery - Inter-row mowing units - Safety
Land- und forstwirtschaftliche Maschinen - Zwischenreihenmäher - Sicherheit
Matériel agricole et forestier - Faucheuses interlignes - Sécurité
Ta slovenski standard je istoveten z: EN 13448:2001
ICS:
65.060.50 Oprema za spravilo pridelkov Harvesting equipment
SIST EN 13448:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13448:2002
---------------------- Page: 2 ----------------------
SIST EN 13448:2002
EUROPEAN STANDARD
EN 13448
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2001
ICS 65.060.50
English version
Agricultural and forestry machinery - Inter-row mowing units -
Safety
Matériel agricole et forestier - Faucheuses interlignes - Land- und forstwirtschaftliche Maschinen -
Sécurité Zwischenreihenmäher - Sicherheit
This European Standard was approved by CEN on 3 October 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13448:2001 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13448:2002
EN 13448:2001 (E)
Contents
page
Foreword.3
Introduction .4
1 Scope .4
2 Normative references .4
3 Terms and definitions.5
4 List of hazards.6
5 Safety requirements and/or measures .6
5.1 General.6
5.2 Protection of cutting elements .6
5.3 Hose protection.7
5.4 Thrown objects .7
5.5 Requirements for pivoting booms .7
5.6 Noise .7
6 Test methods – Thrown object test .8
6.1 General test conditions .8
6.2 Target .8
6.3 Test material.9
6.4 Test method.10
6.5 Acceptance criteria.10
7 Information for use .10
7.1 Instruction handbook .10
7.2 Marking .11
Annex A (normative) List of hazards.12
Annex ZA (informative) Relationship of this document with EC Directives.16
2
---------------------- Page: 4 ----------------------
SIST EN 13448:2002
EN 13448:2001 (E)
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 144 "Tractors and machinery for
agriculture and forestry", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at the latest by
June 2002.
This European Standard has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative annex ZA, which is an integral part of this document.
Annex A is normative and contains the "List of hazards”.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,
France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,
Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 13448:2002
EN 13448:2001 (E)
Introduction
This document is a type C standard as stated in EN 1070.
The machinery concerned and the extent to which hazards are covered is indicated in the scope of this standard.
These hazards are specific to inter-row mowing units.
The hazards that are common to all agriculture machines (self-propelled, mounted, semi-mounted and trailed) are
dealt with in EN 1553:1999.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines that
have been designed and built according to the provisions of this type C standard.
1 Scope
This European Standard specifies the safety requirements and test methods for the design and construction of
inter-row mowing units with vertical spindles mounted on grass cutting machines such as flail mowers, used in
agriculture, forestry and landscaping to cut the grass in the area between two successive obstruction.
It describes methods for elimination or reduction of risks arising from their use.
In addition, it specifies the type of information on safe working practices to be provided by the manufacturer.
This standard is not applicable to rotary mowers and flail-mowers which are covered by EN 745.
Environmental aspects have not been considered in this standard.
This European Standard is not applicable to inter-row mowing units which are manufactured before the date of
publication of this document by CEN.
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other publications. These
normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For
dated references, subsequent amendments to or revisions of any of these publications apply to this European
Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the
publication referred to applies (including amendments).
EN 292-1:1991, Safety of machinery – Basic concepts, general principles for design – Part 1: Basic terminology,
methodology.
EN 292-2:1991, Safety of machinery – Basic concepts, general principles for design – Part 2: Technical principles
and specifications (including amendment A1:1995).
EN 294:1994, Safety of machinery – Safety distances to prevent danger zones being reached by the upper limbs.
EN 745, Agricultural machinery – Rotary mowers and flail mowers – Safety.
EN 1070, Safety of machinery – Terminology.
EN 1553:1999, Agricultural machinery – Agricultural self-propelled, mounted, semi-mounted and trailed machines –
Common safety requirements.
4
---------------------- Page: 6 ----------------------
SIST EN 13448:2002
EN 13448:2001 (E)
EN ISO 3457:1995, Earth-moving machinery – Guards and shields – Definitions and specifications.
3 Terms and definitions
For the purposes of this European Standard, the terms and definitions given in EN 1070 apply together with the
following:
3.1
inter-row mowing unit
rotary mower with vertical spindles equipped with pivoting boom, which allows grass cutting in the area between
two successive obstructions (e.g. trees, posts, etc.) (see Figure 1)
3.2
pivoting boom
device which allows the inter-row mowing unit to perform lateral translation movements parallel to the ground, thus
allowing cutting within the area between two successive obstructions which would not be possible using fixed
mowing machines (see Figure 1)
3.3
sensor
device controlling boom movement, mounted forward of the inter-row mowing unit
NOTE The device may be formed of a metal rod which, when pushed backwards on encountering an obstruction, sends a
command causing the boom to retract. Immediately after the obstacle has been passed, the sensor returns to its original
position, and the boom returns to the working position.
3.4
target
device which registers the number of impacts of objects propelled by the mowing unit
3.5
danger zone
area surrounding the machine with a radius of 50 m as measured from the centre of the unit
Key
1 Blade enclosure
2 Lateral protection
Figure 1 — Inter-row mowing unit
5
---------------------- Page: 7 ----------------------
SIST EN 13448:2002
EN 13448:2001 (E)
4 List of hazards
The hazards, among those which appear in EN 292-1 and EN 292-2 and are considered applicable to machines
covered by the standard are listed in annex A.
Annex A also indicates the hazards which have not been dealt with.
5 Safety requirements and/or measures
5.1 General
Machinery shall comply with the safety requirements and/or protective measures of this clause. In addition, the
machine shall be designed according to the principles of EN 292 for hazards which are not dealt with by this
standard and especially with annex A of EN 292-2:1991/A1:1995 when EN 292 does not give precise
requirements.
Unless otherwise specified in this standard, the machine shall comply with the requirements of EN 1553:1999 and
EN 745 and with Tables 1, 3, 4 and 6 of EN 294:1992.
5.2 Protection of cutting elements
The machine shall be equipped with an imperforate blade enclosure which fully covers the cutting elements,
capable of ensuring a safety distance of at least 50 mm beyond the external trajectory of the cutting elements and
which extend at least 3 mm below the plane of the blade tip circle (see Figure 2).
The blade enclosure shall be free of protrusions and sharp edges and, in the case of a mechanical pivoting boom,
the device which allows the unit to rotate idly when it encounters an obstruction shall be designed, so that the
rotary movement of the cutting elements is not imparted to the blade enclosure itself.
The blade enclosure and the parts of the machine ensuring the guarding shall withstand a vertical downwards load
of 1200 N, and, in order to resist to the forces generated when the blade enclosure hits an obstruction, shall
additionally withstand the following horizontal loads:
600 N for machines intended to be used with a tractor whose maximum power as given in the instruction
handbook is less or equal to 37 kW;
1 000 N for the other machines.
These requirements shall be checked by the test procedure and the test acceptance defined in EN 1553:1999,
annex B.
6
---------------------- Page: 8 ----------------------
SIST EN 13448:2002
EN 13448:2001 (E)
Dimensions in millimetres
Key
1 Ground
2 Blade tip circle
3 Blade enclosure
Figure 2
5.3 Hose protection
In the case of hydraulically or pneumatically operated inter-row mowing units, pipes and hoses shall be fitted,
assembled and if necessary retained to minimise contact with hot surfaces, friction and other unintentional exterior
damage. Visual inspection of hoses and fittings shall be possible except those located inside frames.
Hydraulic hoses containing fluid with a pressure of more than 5 MPa (50 bar) and/or having a temperature over
50 °C, and which are located within 1 m of the operator, shall be guarded in accordance with EN ISO 3457:1995,
4.9.
Any part or component which may divert a possible jet of fluid can be considered as a sufficient protection device.
5.4 Thrown objects
The possibility that objects propelled by the rapid rotary action of the cutting elements during operation, which may
constitute a hazard and risk of injury to the operator, shall be prevented.
Tests shall
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.