SIST EN 61300-2-42:2006

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-42: Tests - Static side load for connectors

This part of IEC 61300 specifies a test to determine the influence of a side load applied to a connector plug. The intention is to simulate the load, due to a length of fibre cable, which would typically be experienced during service. Static side load is also referred to as side pull.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren -- Teil 2-42: Prüfungen - Statische seitliche Zugbelastung für Steckverbinder

Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes fondamentales d'essais et de mesures -- Partie 2-42: Essais - Charge latérale statique pour connecteurs

La présente partie de la EN 61300 spécifie un essai destiné à déterminer l'influence d'une charge latérale appliquée à une fiche de connecteur. L'intention est de simuler la charge exercée par une longueur de câble à fibres, que l'on rencontre généralement au cours du service.

Naprave za medsebojno povezovanje optičnih kablov in pasivne komponente – Osnovni preskusni in merilni postopki – 2-42. del: Preskusi – Statična bočna obremenitev konektorjev (IEC 61300-2-42:2005)

General Information

• Status: Withdrawn
• Publication Date: 28-Feb-2006
• Withdrawal Date: 07-Mar-2022
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: MOC - Mobile Communications
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 08-Mar-2022
• Due Date: 31-Mar-2022
• Completion Date: 08-Mar-2022
• Ref Project: EN 61300-2-42:2005 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for connectors

Relations

• Revised: SIST EN 61300-2-42:2014 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for strain relief
• Effective Date: 06-May-2014
• Replaced By: SIST EN 61300-2-42:2014 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for strain relief
• Effective Date: 07-Jun-2022
• Replaced By: SIST EN 61300-2-42:2014 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-42: Tests - Static side load for strain relief
• Effective Date: 29-Jan-2023
• Replaces: SIST EN 61300-2-42:2002 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-42: Tests - Static side load for connectors
• Effective Date: 29-Jan-2023
• Replaces: SIST EN 61300-2-42:2002 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-42: Tests - Static side load for connectors
• Effective Date: 06-May-2014

Standards Content (Sample)

SLOVENSKI SIST EN 61300-2-42:2006

STANDARD
marec 2006
Naprave za medsebojno povezovanje optičnih kablov in pasivne komponente
– Osnovni preskusni in merilni postopki – 2-42. del: Preskusi – Statična
bočna obremenitev konektorjev (IEC 61300-2-42:2005)
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-42: Tests - Static side load for connectors (IEC
61300-2-42:2005)
ICS 33.180.20 Referenčna številka
SIST EN 61300-2-42:2006(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD EN 61300-2-42
NORME EUROPÉENNE
EUROPÄISCHE NORM September 2005

ICS 33.180.20 Supersedes EN 61300-2-42:1998


English version


Fibre optic interconnecting devices and passive components –
Basic test and measurement procedures
Part 2-42: Tests –
Static side load for connectors
(IEC 61300-2-42:2005)


Dispositifs d'interconnexion et Lichtwellenleiter-Verbindungselemente
composants passifs à fibres optiques - und passive Bauteile –
Méthodes fondamentales d'essais Grundlegende Prüf- und Messverfahren
et de mesures Teil 2-42: Prüfungen –
Partie 2-42: Essais – Statische seitliche Zugbelastung
Charge latérale statique pour connecteurs für Steckverbinder
(CEI 61300-2-42:2005) (IEC 61300-2-42:2005)



This European Standard was approved by CENELEC on 2005-08-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2005 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 61300-2-42:2005 E

---------------------- Page: 2 ----------------------

EN 61300-2-42:2005 - 2 -
Foreword
The text of document 86B/2137/FDIS, future edition 2 of IEC 61300-2-42, prepared by SC 86B, Fibre
optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to
the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61300-2-42 on 2005-08-01.
This European Standard supersedes EN 61300-2-42:1998.
The significant changes include application of the new format for EN 61300 series documents and
modification of the recommended duration for load.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2006-05-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2008-08-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61300-2-42:2005 was approved by CENELEC as a
European Standard without any modification.
__________

---------------------- Page: 3 ----------------------

- 3 - EN 61300-2-42:2005
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
1) 2)
IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 2003
passive components - Basic test and
measurement procedures
Part 1: General and guidance

- 1) 2)
IEC 61300-3-1 Part 3-1: Examinations and EN 61300-3-1 1997
measurements - Visual examination

- 1) 2)
IEC 61300-3-3 Part 3-3: Examinations and EN 61300-3-3 2003
measurements - Active monitoring of
changes in attenuation and return loss

- 1) 2)
IEC 61300-3-4 Part 3-4: Examinations and EN 61300-3-4 2001
measurements - Attenuation





1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 4 ----------------------

NORME CEI
INTERNATIONALE
IEC



61300-2-42
INTERNATIONAL


Deuxième édition
STANDARD

Second edition

2005-07


Dispositifs d'interconnexion et
composants passifs à fibres optiques –
Méthodes fondamentales d'essais
et de mesures –
Partie 2-42:
Essais –
Charge latérale statique pour connecteurs

Fibre optic interconnecting devices
and passive components –
Basic test and measurement procedures –
Part 2-42:
Tests –
Static side load for connectors

 IEC 2005 Droits de reproduction réservés  Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
CODE PRIX
J
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 5 ----------------------

61300-2-42  IEC:2005 – 3 –
CONTENTS
FOREWORD.5

1 Scope.9
2 Normative references.9
3 General description.9
4 Apparatus.11
4.1 Load generator .11
4.2 Holding fixture .11
4.3 Optical source and detector .11
5 Procedure.11
5.1 Preparation of specimens .11
5.2 Pre-conditioning .11
5.3 Initial measurements .11
5.4 Conditioning .11
5.5 Measure the attenuation .13
5.6 Apply cable load .13
5.7 Monitor attenuation.15
5.8 Recovery .15
5.9 Final measurements and examinations .15
5.10 Repeated testing .15
6 Severity .15
7 Details to be specified.15

Figure 1 – Example of the static side load test arrangement .13

Table 1 – Recommended load and durations for varying cable diameters.13

---------------------- Page: 6 ----------------------

61300-2-42  IEC:2005 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
__________

FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-42: Tests –
Static side load for connectors


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relev
...