SIST EN 4708-102:2018

Aerospace series - Sleeving, heat-shrinkable, for binding, insulation and identification - Part 102: Very flexible polymer - Operating temperature - 75 °C to 150 °C - Product standard

This document specifies the required characteristics for a heat-shrinkable, very flexible polymer sleeving for use in aircraft electrical systems at operating temperatures between ‒ 75 °C to 150 °C. This sleeving has very good flexibility, is flame retarded and has a thick wall for mechanical protection. It is suitable for use as cable protection in areas where wiring is subject to contamination by aircraft fuels and hydraulic fluids.
These sleevings are normally supplied with internal diameters up to 102 mm for shrink ratios of 2:1. They are available in black only.
Sizes other than those specifically listed in this standard may be available. These items shall be considered to comply with this standard if they comply with the property requirements listed in Tables 2, 3 and 4 except for dimensions and mass.

Luft- und Raumfahrt - Wärmeschrumpfender Schlauch zur Befestigung, Isolierung und Identifizierung - Teil 102: Hochflexibles Polymer - Temperaturbereich - 75 °C und 150 °C - Produktnorm

Série aérospatiale - Manchons thermorétractables, de jonction, isolement et identification - Partie 102 : Polymère très flexible - Températures d'utilisation - 75 °C à 150 °C - Norme de produit

Aeronavtika - Toplotno skrčljiva cev za utrjevanje, izolacijo in identifikacijo - 102. del: Zelo fleksibilen polimer - Delovna temperatura med –75 °C in 150 °C - Standard za proizvod

Ta dokument določa zahtevane lastnosti toplotno skrčljivih zelo fleksibilnih polimernih cevi za uporabo v električnih sistemih letal pri obratovalnih temperaturah med ‒75 °C in 150 °C. Te cevi vključujejo izjemno fleksibilnost, ognjeodpornost in debelo steno za mehansko zaščito. Primerne so za uporabo kot zaščita kablov na območjih, kjer je ožičenje izpostavljeno onesnaženju z gorivi in hidravličnimi tekočinami za letala.
Te cevi so običajno dobavljive z notranjimi premeri do 102 mm za razmerja krčenja 2:1. Na voljo so samo v črni barvi.
Lahko so na voljo tudi v velikostih, ki niso posebej navedene v tem standardu. Upoštevati je treba, da se te postavke skladajo s tem standardom, če so skladne z zahtevami za lastnosti, navedenimi v tabelah 2, 3 in 4, razen z zahtevami za mere in težo.

General Information

• Status: Published
• Publication Date: 05-Nov-2018
• ICS: 49.060 - Aerospace electric equipment and systems
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 26-Oct-2018
• Due Date: 31-Dec-2018
• Completion Date: 06-Nov-2018
• Ref Project: EN 4708-102:2018 - Aerospace series - Sleeving, heat-shrinkable, for binding, insulation and identification - Part 102: Very flexible polymer - Operating temperature - 75 °C to 150 °C - Product standard

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Luft- und Raumfahrt - Wärmeschrumpfender Schlauch zur Befestigung, Isolierung und Identifizierung - Teil 102: Hochflexibles Polymer - Temperaturbereich - 75 °C und 150 °C - ProduktnormSérie aérospatiale - Manchons thermorétractables, de jonction, isolement et identification - Partie 102 : Polymère très flexible - Températures d'utilisation - 75 °C à 150 °C - Norme de produitAerospace series - Sleeving, heat-shrinkable, for binding, insulation and identification - Part 102: Very flexible polymer - Operating temperature - 75 °C to 150 °C - Product standard49.060Aerospace electric equipment and systemsICS:Ta slovenski standard je istoveten z:EN 4708-102:2018SIST EN 4708-102:2018en,fr,de01-december-2018SIST EN 4708-102:2018SLOVENSKI
STANDARD



SIST EN 4708-102:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4708-102
October
t r s z ICS
v {ä r x r English Version
Aerospace series æ Sleevingá heatæshrinkableá for bindingá insulation and identification æ Part
s r tã Very flexible polymer æ Operating temperature æ
y w
¹C to
s w r
¹C æ Product standard Série aérospatiale æ Manchons thermorétractablesá de jonctioná isolement et identification æ Partie
s r t ã Polymère très flexible æ Températures d 5utilisation æ
y w
¹C à
s w r
¹C æ Norme de produit
Luftæ und Raumfahrt æ Wärmeschrumpfender Schlauch zur Befestigungá Isolierung und Identifizierung æ Teil
s r tã Hochflexibles Polymer æ Temperaturbereich æ
y w
¹C und
s w r
¹C æ Produktnorm This European Standard was approved by CEN on
z July
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
v y r zæ s r tã t r s z ESIST EN 4708-102:2018



EN 4708-102:2018 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Required characteristics . 5 5 Quality assurance . 11 6 Designation . 11 7 Labelling and packaging . 11 8 Technical specification . 11
SIST EN 4708-102:2018



EN 4708-102:2018 (E) 3 European foreword This document (EN 4708-102:2018) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be withdrawn at the latest by April 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. SIST EN 4708-102:2018



EN 4708-102:2018 (E) 4 1 Scope This European Standard specifies the required characteristics for a heat-shrinkable, very flexible polymer sleeving for use in aircraft electrical systems at operating temperatures between
y w °C to 150 °C. This sleeving has very good flexibility, is flame retarded and has a thick wall for mechanical protection. It is suitable for use as cable protection in areas where wiring is subject to contamination by aircraft fuels and hydraulic fluids. These sleevings are normally supplied with internal diameters up to 102 mm for shrink ratios of 2:1. They are available in black only. Sizes other than those specifically listed in this standard may be available. These items shall be considered to comply with this standard if they comply with the property requirements listed in Tables 2, 3 and 4 except for dimensions and mass. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
EN 3909, Aerospace series — Test fluids and test methods for electrical and optical components and sub-assemblies EN 4708-001, Aerospace series — Sleeving, heat-shrinkable, for binding, insulation and identification — Part 001: Technical specification EN ISO 846, Plastics — Evaluation of the action of microorganisms (ISO 846) IEC 60684-1, Flexible insulating sleeving — Part 1: Definitions and general requirements 1) IEC 60684-2, Flexible insulating sleeving — Part 2: Methods of test 1) IEC 60757, Code for designation of colours 1) 3 Terms and definitions For the purposes of this document, the terms and definitions given in IEC 60684-1 apply. ISO and IEC maintain terminological databases for use in standardization at the following addresses:
IEC Electropedia: availab
...