Machines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-4: Concrete pipe coating machines

This European Standard applies to concrete pipe coating machines.
This European Standard deals with the significant hazards listed in clause 4, when used as intended under the conditions foreseen by the manufacturer. This European Standard specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, except noise hazards.
NOTE   Amendment is under preparation to deal with noise, in particular for measures to reduce noise at source and a noise test code including noise declaration.
This standard establishes safety requirements and/or methods of protection which applies to these machines.
This European standard applies to the concrete pipe coating making machines which may form an integral part of a pipe making process plant.
See 1.4 of EN 12629-1:2000.

Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 5-4: Maschinen zum Beschichten von Betonrohren

1.1   Diese Europäische Norm gilt für Maschinen zum Beschichten von Betonrohren.
1.2   Diese Europäische Norm behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefähr-dungsereignisse (siehe Abschnitt 4), die auf diese Maschinen zutreffen, wenn sie bestimmungsgemäß und ent-sprechend den vorhersehbaren Empfehlungen des Herstellers verwendet werden. Diese Europäische Norm spezi-fiziert die entsprechenden technischen Maßnahmen zur Beseitigung oder Verminderung der Risiken, die von die-sen Gefährdungen ausgehen, außer Gefährdungen durch Lärm.
ANMERKUNG   Eine Änderung ist in Vorbereitung, die Lärm behandelt sowie insbesondere Maßnahmen zur Lärmminderung an der Quelle und ein Geräuschmessverfahren einschließlich der Angabe von Geräuschemissionswerten.
Diese Norm behandelt Sicherheitsanforderungen und/oder Schutzmaßnahmen, die für diese Maschinen gelten.
1.3   Diese Europäische Norm gilt für Maschinen zum Beschichten von Betonrohren, die als integraler Bestandteil einer Rohrherstellungsanlage dienen können.
1.4   Siehe 1.4 von EN 12629-1:2000.

Machines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 5-4: Machines de revetement des tuyaux en béton

Stroji za izdelavo gradbenih proizvodov iz betona in apnenega peščenca - Varnost - 5-4. del: Stroji za nanašanje premazov na betonske cevi

General Information

Status
Withdrawn
Publication Date
31-Aug-2004
Withdrawal Date
13-Oct-2010
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
13-Oct-2010
Due Date
05-Nov-2010
Completion Date
14-Oct-2010

Relations

Buy Standard

Standard
EN 12629-5-4:2004
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Maschinen für die Herstellung von Bauprodukten aus Beton und Kalksandsteinmassen - Sicherheit - Teil 5-4: Maschinen zum Beschichten von BetonrohrenMachines pour la fabrication de produits de construction en béton et silico-calcaire - Sécurité - Partie 5-4: Machines de revetement des tuyaux en bétonMachines for the manufacture of constructional products from concrete and calcium-silicate - Safety - Part 5-4: Concrete pipe coating machines91.220Gradbena opremaConstruction equipmentICS:Ta slovenski standard je istoveten z:EN 12629-5-4:2003SIST EN 12629-5-4:2004en01-september-2004SIST EN 12629-5-4:2004SLOVENSKI
STANDARD



SIST EN 12629-5-4:2004



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12629-5-4December 2003ICS 91.220English versionMachines for the manufacture of constructional products fromconcrete and calcium-silicate - Safety - Part 5-4: Concrete pipecoating machinesMachines pour la fabrication de produits de construction enbéton et silico-calcaire - Sécurité - Partie 5-4: Machines derevêtement des tuyaux en bétonMaschinen für die Herstellung von Bauprodukten aus Betonund Kalksandsteinmassen - Sicherheit - Teil 5-4:Maschinen zum Beschichten von BetonrohrenThis European Standard was approved by CEN on 3 November 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12629-5-4:2003: ESIST EN 12629-5-4:2004



EN 12629-5-4:2003 (E)2ContentspageForeword.3Introduction.41Scope.52Normative references.53Terms and definitions.54List of significant hazards.65Safety requirements and/or measures.76Verification of safety requirements and/or measures.87Information for use.88Marking.8Annex A (informative)
Definitions of terms.9Annex B (informative)
Hazard zones.11Annex ZA (informative)
Relationship of this document with EC Directives.13Bibliography.14SIST EN 12629-5-4:2004



EN 12629-5-4:2003 (E)3ForewordThis document (EN 12629-5-4:2003) has been prepared by Technical Committee CEN/TC 151 “Constructionequipment and building material machines - Safety”, the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn at the latest byJune 2004.This document has been prepared under a mandate given to CEN by the European Commission and the EuropeanFree Trade Association, and supports essential requirements of EU Directive(s).For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document.The series "Machines for the manufacture of constructional products from concrete and calcium - silicate - Safety"consists of following parts :Part 1 :Common requirementsPart 2 :Block making machinesPart 3 :Slide and turntable machinesPart 4 :Concrete rooftile making machinesPart 5.1 :Concrete pipe machines manufacturing in the vertical axis.Part 5.2 :Concrete pipe machines manufacturing in the horizontal axisPart 5.3 :Pipe prestressing machinesPart 5.4 :Concrete pipe coating machinesPart 6 :Stationary and mobile equipment for the manufacture of precast reinforced productsPart 7 :Stationary and mobile equipment for the benched manufacture of prestressed productsPart 8 :Machines and equipment for the manufacture of constructional products from calcium silicate (andconcrete).Annex A is informative and contains "Definitions of terms", annex B is informative and contains "Hazard zones".According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 12629-5-4:2004



EN 12629-5-4:2003 (E)4IntroductionThis European Standard is a Type C-standard as stated in EN 1070.The machinery concerned and the extend to which hazards, hazardous situations and events are covered areindicated in the scope of this Standard.When provisions of this type C standard are different from those which are stated in type A or B standards, theprovisions of this type C standard take precedence over the provisions of the other standards, for machines thathave been designed and built according to the provisions of this type C standard.Reference to pertinent standards of this kind is made were such standards are applicable and so far necessary.SIST EN 12629-5-4:200
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.