ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 246 GHz - Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Short Range Devices (SRD) and
ancillary equipment in respect of ElectroMagnetic Compatibility (EMC).
The present document specifies the applicable test conditions, performance assessment, and performance criteria for
Short Range Devices (SRD) and the associated ancillary equipment.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and the ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in the ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port
of radio equipment and combinations of radio and associated ancillary equipment are not included in the present
document. Such technical specifications are normally found in the relevant product standards for the effective use of the
radio spectrum.
The present document, together with ETSI EN 301 489-1 [1], are aimed to cover requirements to demonstrate an
adequate level of electromagnetic compatibility.

Standard elektromagnetne združljivosti (EMC) za radijsko opremo in storitve - 3. del: Posebni pogoji za naprave kratkega dosega (SRD), delujoče na frekvencah med 9 kHz in 246 GHz - Harmonizirani standard, ki zajema bistvene zahteve člena 3.1(b) direktive 2014/53/EU

Ta dokument skupaj s standardom ETSI EN 301 489-1 [1] zajema oceno naprav kratkega dosega (SRD) in pomožne opreme v zvezi z elektromagnetno združljivostjo (EMC).
Ta dokument določa veljavne preskusne pogoje, oceno zmogljivosti in kriterije zmogljivosti za naprave kratkega dosega (SRD) ter povezano pomožno opremo.
Če se ta dokument in standard ETSI EN 301 489-1 [1] razlikujeta (na primer glede posebnih pogojev, opredelitev, kratic), imajo prednost določbe tega dokumenta.
Okoljska razvrstitev ter zahteve glede sevanja in odpornosti iz tega dokumenta so navedene v standardu ETSI EN 301 489-1 [1], razen posebnih pogojev iz tega dokumenta.
Ta dokument ne vključuje tehničnih specifikacij v zvezi z antenskim vhodom radijske opreme in sevanjem iz vhoda na ohišju radijske opreme ter kombinacijami radijske opreme in povezane pomožne opreme. Take tehnične specifikacije so običajno navedene v ustreznih standardih za izdelek na področju učinkovite uporabe radijskega spektra.
Namen tega dokumenta skupaj s standardom ETSI EN 301 489-1 [1] je podati zahteve, s katerimi se dokazuje ustrezna raven elektromagnetne združljivosti.

General Information

Status
Published
Public Enquiry End Date
30-Nov-2016
Publication Date
14-Apr-2019
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Apr-2019
Due Date
06-Jun-2019
Completion Date
15-Apr-2019
Mandate

Buy Standard

Standard
ETSI EN 301 489-3 V2.1.1 (2019-03) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 246 GHz; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
English language
19 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
SIST EN 301 489-3 V2.1.1:2019
English language
19 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 301 489-3 V2.1.1 (2017-03) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 246 GHz; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
English language
19 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 301 489-3 V2.1.0 (2016-09) - ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9 kHz and 246 GHz; Harmonised Standard covering the essential requirements of article 3.1(b) of Directive 2014/53/EU
English language
19 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

ETSI EN 301 489-3 V2.1.1 (2019-03)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 3: Specific conditions for Short-Range Devices (SRD)
operating on frequencies between 9 kHz and 246 GHz;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 301 489-3 V2.1.1 (2019-03)
Reference
REN/ERM-EMC-332
Keywords
EMC, harmonised standard, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

TM TM

3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and

of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 301 489-3 V2.1.1 (2019-03)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

Introduction ........................................................................................................................................................ 6

1 Scope ........................................................................................................................................................ 7

2 References ................................................................................................................................................ 7

2.1 Normative references ......................................................................................................................................... 7

2.2 Informative references ........................................................................................................................................ 7

3 Definitions, symbols and abbreviations ................................................................................................... 8

3.1 Definitions .......................................................................................................................................................... 8

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Environmental profile ......................................................................................................................................... 8

4.3 Test signal connections ...................................................................................................................................... 9

4.3.1 General .......................................................................................................................................................... 9

4.3.2 Equipment with an external antenna connector ............................................................................................ 9

4.3.3 Equipment without an external antenna connector (integral antenna) .......................................................... 9

4.3.4 Equipment with more than one antenna ........................................................................................................ 9

4.4 Narrow band responses of receivers ................................................................................................................... 9

4.5 Arrangements for testing .................................................................................................................................... 9

4.5.1 Testing transmitter and receiver together (as a system) ................................................................................ 9

4.5.2 Operating modes ......................................................................................................................................... 10

4.6 RF Exclusion bands .......................................................................................................................................... 10

4.6.1 General ........................................................................................................................................................ 10

4.6.2 Exclusion bands for emissions testing ........................................................................................................ 10

4.6.2.1 Transmitters .......................................................................................................................................... 10

4.6.2.2 Receivers ............................................................................................................................................... 10

4.6.2.3 Duplex and multi-mode equipment ....................................................................................................... 10

4.6.3 Exclusion bands for immunity testing ........................................................................................................ 11

4.6.3.1 Transmitters .......................................................................................................................................... 11

4.6.3.2 Receivers ............................................................................................................................................... 11

4.6.3.3 Duplex and multi-mode equipment ....................................................................................................... 11

5 Performance assessment ......................................................................................................................... 11

5.1 General ............................................................................................................................................................. 11

5.2 Continuous and non-continuous communication links ..................................................................................... 12

5.3 Functions other than a communications link .................................................................................................... 12

5.4 Associated test equipment ................................................................................................................................ 12

5.5 Ancillary equipment ......................................................................................................................................... 12

5.6 Equipment classification .................................................................................................................................. 12

6 Performance Criteria .............................................................................................................................. 13

6.1 Introduction ...................................................................................................................................................... 13

6.2 Performance Criteria ........................................................................................................................................ 13

7 Applicability Overview .......................................................................................................................... 13

7.1 General ............................................................................................................................................................. 13

7.2 Special conditions for emissions ...................................................................................................................... 13

7.3 Special conditions for immunity ...................................................................................................................... 14

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 15

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 301 489-3 V2.1.1 (2019-03)

Annex B (informative): Examples of Short Range Devices (SRD) in the scope of the present

document ........................................................................................................ 17

Annex C (informative): Change History .............................................................................................. 18

History .............................................................................................................................................................. 19

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 301 489-3 V2.1.1 (2019-03)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM).

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document is part 3 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 8 May 2017
Date of latest announcement of this EN (doa): 30 June 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2019
Date of withdrawal of any conflicting National Standard (dow): 31 December 2020
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 301 489-3 V2.1.1 (2019-03)
Introduction

The product family of Short Range Devices covers a wide range of equipment types, which may have different sets of

performance criteria set out in the relevant radio standards and/or product standards.

The present document is intended for all SRD types and applies a standard set of performance criteria. This includes the

requirement that the equipment continues to operate as intended under certain standardised conditions of EMC stress.

The term "Short Range Device" (SRD) is intended to cover the radio equipment which provides either uni-directional or

bi-directional communication and which have low capability of causing interference to other radio equipment. SRDs

use either integral, dedicated or external antennas and all modes of modulation can be permitted subject to relevant

standards. For Short Range Devices individual licenses are normally not required.

ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 301 489-3 V2.1.1 (2019-03)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Short Range Devices (SRD) and

ancillary equipment in respect of ElectroMagnetic Compatibility (EMC).

The present document specifies the applicable test conditions, performance assessment, and performance criteria for

Short Range Devices (SRD) and the associated ancillary equipment.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and the ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in the ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port

of radio equipment and combinations of radio and associated ancillary equipment are not included in the present

document. Such technical specifications are normally found in the relevant product standards for the effective use of the

radio spectrum.

The present document, together with ETSI EN 301 489-1 [1], are aimed to cover requirements to demonstrate an

adequate level of electromagnetic compatibility.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.2.0) (03-2017): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements; Harmonised Standard

covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential

requirements of article 6 of Directive 2014/30/EU".

[2] ETSI EN 300 220-1 (V3.1.1) (02-2017): "Short Range Devices (SRD) operating in the frequency

range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".

2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 301 489-3 V2.1.1 (2019-03)

[i.2] ETSI TR 103 088: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Using the

ETSI EN 301 489 series of EMC standards".

[i.3] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European
...

SLOVENSKI STANDARD
SIST EN 301 489-3 V2.1.1:2019
01-junij-2019
6WDQGDUGHOHNWURPDJQHWQH]GUXåOMLYRVWL (0& ]DUDGLMVNRRSUHPRLQVWRULWYH
GHO3RVHEQLSRJRML]DQDSUDYHNUDWNHJDGRVHJD 65' GHOXMRþHQDIUHNYHQFDK
PHGN+]LQ*+]+DUPRQL]LUDQLVWDQGDUGNL]DMHPDELVWYHQH]DKWHYHþOHQD
 E GLUHNWLYH(8

ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part 3:

Specific conditions for Short-Range Devices (SRD) operating on frequencies between 9

kHz and 246 GHz - Harmonised Standard covering the essential requirements of article

3.1(b) of Directive 2014/53/EU
Ta slovenski standard je istoveten z: ETSI EN 301 489-3 V2.1.1 (2019-03)
ICS:
33.060.20 Sprejemna in oddajna Receiving and transmitting
oprema equipment
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST EN 301 489-3 V2.1.1:2019 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 301 489-3 V2.1.1:2019
---------------------- Page: 2 ----------------------
SIST EN 301 489-3 V2.1.1:2019
ETSI EN 301 489-3 V2.1.1 (2019-03)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 3: Specific conditions for Short-Range Devices (SRD)
operating on frequencies between 9 kHz and 246 GHz;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 3 ----------------------
SIST EN 301 489-3 V2.1.1:2019
2 ETSI EN 301 489-3 V2.1.1 (2019-03)
Reference
REN/ERM-EMC-332
Keywords
EMC, harmonised standard, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI

deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

TM TM

3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and

of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 301 489-3 V2.1.1:2019
3 ETSI EN 301 489-3 V2.1.1 (2019-03)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

Introduction ........................................................................................................................................................ 6

1 Scope ........................................................................................................................................................ 7

2 References ................................................................................................................................................ 7

2.1 Normative references ......................................................................................................................................... 7

2.2 Informative references ........................................................................................................................................ 7

3 Definitions, symbols and abbreviations ................................................................................................... 8

3.1 Definitions .......................................................................................................................................................... 8

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Environmental profile ......................................................................................................................................... 8

4.3 Test signal connections ...................................................................................................................................... 9

4.3.1 General .......................................................................................................................................................... 9

4.3.2 Equipment with an external antenna connector ............................................................................................ 9

4.3.3 Equipment without an external antenna connector (integral antenna) .......................................................... 9

4.3.4 Equipment with more than one antenna ........................................................................................................ 9

4.4 Narrow band responses of receivers ................................................................................................................... 9

4.5 Arrangements for testing .................................................................................................................................... 9

4.5.1 Testing transmitter and receiver together (as a system) ................................................................................ 9

4.5.2 Operating modes ......................................................................................................................................... 10

4.6 RF Exclusion bands .......................................................................................................................................... 10

4.6.1 General ........................................................................................................................................................ 10

4.6.2 Exclusion bands for emissions testing ........................................................................................................ 10

4.6.2.1 Transmitters .......................................................................................................................................... 10

4.6.2.2 Receivers ............................................................................................................................................... 10

4.6.2.3 Duplex and multi-mode equipment ....................................................................................................... 10

4.6.3 Exclusion bands for immunity testing ........................................................................................................ 11

4.6.3.1 Transmitters .......................................................................................................................................... 11

4.6.3.2 Receivers ............................................................................................................................................... 11

4.6.3.3 Duplex and multi-mode equipment ....................................................................................................... 11

5 Performance assessment ......................................................................................................................... 11

5.1 General ............................................................................................................................................................. 11

5.2 Continuous and non-continuous communication links ..................................................................................... 12

5.3 Functions other than a communications link .................................................................................................... 12

5.4 Associated test equipment ................................................................................................................................ 12

5.5 Ancillary equipment ......................................................................................................................................... 12

5.6 Equipment classification .................................................................................................................................. 12

6 Performance Criteria .............................................................................................................................. 13

6.1 Introduction ...................................................................................................................................................... 13

6.2 Performance Criteria ........................................................................................................................................ 13

7 Applicability Overview .......................................................................................................................... 13

7.1 General ............................................................................................................................................................. 13

7.2 Special conditions for emissions ...................................................................................................................... 13

7.3 Special conditions for immunity ...................................................................................................................... 14

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 15

ETSI
---------------------- Page: 5 ----------------------
SIST EN 301 489-3 V2.1.1:2019
4 ETSI EN 301 489-3 V2.1.1 (2019-03)

Annex B (informative): Examples of Short Range Devices (SRD) in the scope of the present

document ........................................................................................................ 17

Annex C (informative): Change History .............................................................................................. 18

History .............................................................................................................................................................. 19

ETSI
---------------------- Page: 6 ----------------------
SIST EN 301 489-3 V2.1.1:2019
5 ETSI EN 301 489-3 V2.1.1 (2019-03)
Intellectual Property Rights
Essential patents

IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Trademarks

The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.

ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no

right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does

not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.

Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM).

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document is part 3 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 8 May 2017
Date of latest announcement of this EN (doa): 30 June 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2019
Date of withdrawal of any conflicting National Standard (dow): 31 December 2020
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 7 ----------------------
SIST EN 301 489-3 V2.1.1:2019
6 ETSI EN 301 489-3 V2.1.1 (2019-03)
Introduction

The product family of Short Range Devices covers a wide range of equipment types, which may have different sets of

performance criteria set out in the relevant radio standards and/or product standards.

The present document is intended for all SRD types and applies a standard set of performance criteria. This includes the

requirement that the equipment continues to operate as intended under certain standardised conditions of EMC stress.

The term "Short Range Device" (SRD) is intended to cover the radio equipment which provides either uni-directional or

bi-directional communication and which have low capability of causing interference to other radio equipment. SRDs

use either integral, dedicated or external antennas and all modes of modulation can be permitted subject to relevant

standards. For Short Range Devices individual licenses are normally not required.

ETSI
---------------------- Page: 8 ----------------------
SIST EN 301 489-3 V2.1.1:2019
7 ETSI EN 301 489-3 V2.1.1 (2019-03)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Short Range Devices (SRD) and

ancillary equipment in respect of ElectroMagnetic Compatibility (EMC).

The present document specifies the applicable test conditions, performance assessment, and performance criteria for

Short Range Devices (SRD) and the associated ancillary equipment.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and the ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in the ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port

of radio equipment and combinations of radio and associated ancillary equipment are not included in the present

document. Such technical specifications are normally found in the relevant product standards for the effective use of the

radio spectrum.

The present document, together with ETSI EN 301 489-1 [1], are aimed to cover requirements to demonstrate an

adequate level of electromagnetic compatibility.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.2.0) (03-2017): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Part 1: Common technical requirements; Harmonised Standard

covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential

requirements of article 6 of Directive 2014/30/EU".

[2] ETSI EN 300 220-1 (V3.1.1) (02-2017): "Short Range Devices (SRD) operating in the frequency

range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".

2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.
ETSI
---------------------- Page: 9 -------------------
...

Final draft ETSI EN 301 489-3 V2.1.1 (2017-03)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 3: Specific conditions for Short-Range Devices (SRD)
operating on frequencies between 9 kHz and 246 GHz;
Harmonised Standard covering the essential requirements of
article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 489-3 V2.1.1 (2017-03)
Reference
REN/ERM-EMC-332
Keywords
EMC, harmonised standard, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 489-3 V2.1.1 (2017-03)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

Introduction ........................................................................................................................................................ 5

1 Scope ........................................................................................................................................................ 7

2 References ................................................................................................................................................ 7

2.1 Normative references ......................................................................................................................................... 7

2.2 Informative references ........................................................................................................................................ 8

3 Definitions, symbols and abbreviations ................................................................................................... 8

3.1 Definitions .......................................................................................................................................................... 8

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Environmental profile ......................................................................................................................................... 9

4.3 Test signal connections ...................................................................................................................................... 9

4.3.1 General .......................................................................................................................................................... 9

4.3.2 Equipment with an external antenna connector ............................................................................................ 9

4.3.3 Equipment without an external antenna connector (integral antenna) .......................................................... 9

4.3.4 Equipment with more than one antenna ........................................................................................................ 9

4.4 Narrow band responses of receivers ................................................................................................................. 10

4.5 Arrangements for testing .................................................................................................................................. 10

4.5.1 Testing transmitter and receiver together (as a system) .............................................................................. 10

4.5.2 Operating modes ......................................................................................................................................... 10

4.6 RF Exclusion bands .......................................................................................................................................... 10

4.6.1 General ........................................................................................................................................................ 10

4.6.2 Exclusion bands for emissions testing ........................................................................................................ 10

4.6.2.1 Transmitters .......................................................................................................................................... 10

4.6.2.2 Receivers ............................................................................................................................................... 11

4.6.2.3 Duplex and multi-mode equipment ....................................................................................................... 11

4.6.3 Exclusion bands for immunity testing ........................................................................................................ 11

4.6.3.1 Transmitters .......................................................................................................................................... 11

4.6.3.2 Receivers ............................................................................................................................................... 11

4.6.3.3 Duplex and multi-mode equipment ....................................................................................................... 11

5 Performance assessment ......................................................................................................................... 12

5.1 General ............................................................................................................................................................. 12

5.2 Continuous and non-continuous communication links ..................................................................................... 12

5.3 Functions other than a communications link .................................................................................................... 12

5.4 Associated test equipment ................................................................................................................................ 12

5.5 Ancillary equipment ......................................................................................................................................... 12

5.6 Equipment classification .................................................................................................................................. 13

6 Performance Criteria .............................................................................................................................. 13

6.1 Introduction ...................................................................................................................................................... 13

6.2 Performance Criteria ........................................................................................................................................ 13

7 Applicability Overview .......................................................................................................................... 13

7.1 General ............................................................................................................................................................. 13

7.2 Special conditions for emissions ...................................................................................................................... 13

7.3 Special conditions for immunity ...................................................................................................................... 14

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 15

ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 489-3 V2.1.1 (2017-03)

Annex B (informative): Examples of Short Range Devices (SRD) in the scope of the present

document ........................................................................................................ 17

Annex C (informative): Change History .............................................................................................. 18

History .............................................................................................................................................................. 19

ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 489-3 V2.1.1 (2017-03)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee

Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the

ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document is part 3 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

Introduction

The product family of Short Range Devices covers a wide range of equipment types, which may have different sets of

performance criteria set out in the relevant radio standards and/or product standards.

The present document is intended for all SRD types and applies a standard set of performance criteria. This includes the

requirement that the equipment continues to operate as intended under certain standardised conditions of EMC stress.

ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 489-3 V2.1.1 (2017-03)

The term "Short Range Device" (SRD) is intended to cover the radio equipment which provides either uni-directional or

bi-directional communication and which have low capability of causing interference to other radio equipment. SRDs

use either integral, dedicated or external antennas and all modes of modulation can be permitted subject to relevant

standards. For Short Range Devices individual licenses are normally not required.

ETSI
---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 489-3 V2.1.1 (2017-03)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Short Range Devices (SRD) and

ancillary equipment in respect of ElectroMagnetic Compatibility (EMC).

The present document specifies the applicable test conditions, performance assessment, and performance criteria for

Short Range Devices (SRD) and the associated ancillary equipment.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and the ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in the ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port

of radio equipment and combinations of radio and associated ancillary equipment are not included in the present

document. Such technical specifications are normally found in the relevant product standards for the effective use of the

radio spectrum.

The present document, together with ETSI EN 301 489-1 [1], are aimed to cover requirements to demonstrate an

adequate level of electromagnetic compatibility.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.2.0) (03-2017): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Harmonised Standard covering the essential requirements of

article 3.1(b) of the Directive 2014/53/EU and the essential requirements of article 6 of the

Directive 2014/30/EU; Part 1: Common technical requirements".

[2] ETSI EN 300 220-1 (V3.1.1) (02-2017): "Short Range Devices (SRD) operating in the frequency

range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".

2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.
ETSI
---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 489-3 V2.1.1 (2017-03)

[i.2] ETSI TR 103 088: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Using the

ETSI EN 301 489 series of EMC standards".

[i.3] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotechnical Standardisation and to the European

Telecommunications Standards Institute as regards radio equipment in support of Directive

2014/53/EU of the European Parliament and of the Council.
3 Definitions, symbols and abbreviations
3.1 Definitions

For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1], ETSI

EN 300 220-1 [2] and in the Direc
...

Draft ETSI EN 301 489-3 V2.1.0 (2016-09)
HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 3: Specific conditions for Short-Range Devices (SRD)
operating on frequencies between 9 kHz and 246 GHz;
Harmonised standard covering the essential requirements of
article 3.1(b) of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 489-3 V2.1.0 (2016-09)
Reference
REN/ERM-EMC-332
Keywords
EMC, harmonised standard, SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 489-3 V2.1.0 (2016-09)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

Introduction ........................................................................................................................................................ 5

1 Scope ........................................................................................................................................................ 7

2 References ................................................................................................................................................ 7

2.1 Normative references ......................................................................................................................................... 7

2.2 Informative references ........................................................................................................................................ 8

3 Definitions, symbols and abbreviations ................................................................................................... 8

3.1 Definitions .......................................................................................................................................................... 8

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 8

4 Test conditions ......................................................................................................................................... 8

4.1 General ............................................................................................................................................................... 8

4.2 Environmental profile ......................................................................................................................................... 9

4.3 Test signal connections ...................................................................................................................................... 9

4.3.1 General .......................................................................................................................................................... 9

4.3.2 Equipment with an external antenna connector ............................................................................................ 9

4.3.3 Equipment without an external antenna connector (integral antenna) .......................................................... 9

4.3.4 Equipment with more than one antenna ........................................................................................................ 9

4.4 Narrow band responses of receivers ................................................................................................................... 9

4.5 Arrangements for testing .................................................................................................................................. 10

4.5.1 Testing transmitter and receiver together (as a system) .............................................................................. 10

4.5.2 Operating modes ......................................................................................................................................... 10

4.6 RF Exclusion bands .......................................................................................................................................... 10

4.6.1 General ........................................................................................................................................................ 10

4.6.2 Exclusion bands for emissions testing ........................................................................................................ 10

4.6.2.1 Transmitters .......................................................................................................................................... 10

4.6.2.2 Receivers ............................................................................................................................................... 10

4.6.2.3 Duplex and multi mode equipment ....................................................................................................... 11

4.6.3 Exclusion bands for immunity testing ........................................................................................................ 11

4.6.3.1 Transmitters .......................................................................................................................................... 11

4.6.3.2 Receivers ............................................................................................................................................... 11

4.6.3.3 Duplex and multi mode equipment ....................................................................................................... 11

5 Performance assessment ......................................................................................................................... 12

5.1 General ............................................................................................................................................................. 12

5.2 Continuous and non-continuous communication links ..................................................................................... 12

5.3 Functions other than a communications link .................................................................................................... 12

5.4 Associated test equipment ................................................................................................................................ 12

5.5 Ancillary equipment ......................................................................................................................................... 12

5.6 Equipment classification .................................................................................................................................. 13

6 Performance Criteria .............................................................................................................................. 13

6.1 Introduction ...................................................................................................................................................... 13

6.2 Performance Criteria ........................................................................................................................................ 13

7 Applicability Overview .......................................................................................................................... 13

7.1 General ............................................................................................................................................................. 13

7.2 Special conditions for emissions ...................................................................................................................... 13

7.3 Special conditions for immunity ...................................................................................................................... 14

Annex A (normative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 15

ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 489-3 V2.1.0 (2016-09)

Annex B (informative): Examples of Short Range Devices (SRD) in the scope of the present

document ........................................................................................................ 17

Annex C (informative): Change History .............................................................................................. 18

History .............................................................................................................................................................. 19

ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 489-3 V2.1.0 (2016-09)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote

phase of the ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.1].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document is part 3 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

Introduction

The product family of Short Range Devices covers a wide range of equipment types, which may have different sets of

performance criteria set out in the relevant radio standards and/or product standards.

The present document is intended for all SRD types and applies a standard set of performance criteria. This includes the

requirement that the equipment continues to operate as intended under certain standardised conditions of EMC stress.

ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 489-3 V2.1.0 (2016-09)

The term "Short Range Device" (SRD) is intended to cover the radio equipment which provides either uni-directional or

bi-directional communication and which have low capability of causing interference to other radio equipment. SRDs

use either integral, dedicated or external antennas and all modes of modulation can be permitted subject to relevant

standards. For Short Range Devices individual licenses are normally not required.

ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 489-3 V2.1.0 (2016-09)
1 Scope

The present document, together with ETSI EN 301 489-1 [1], covers the assessment of Short Range Devices (SRD) and

ancillary equipment in respect of ElectroMagnetic Compatibility (EMC).

The present document specifies the applicable test conditions, performance assessment, and performance criteria for

Short Range Devices (SRD) and the associated ancillary equipment.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and the ETSI EN 301 489-1 [1], the provisions of the present document take precedence.

The environmental classification and the emission and immunity requirements used in the present document are as

stated in the ETSI EN 301 489-1 [1], except for any special conditions included in the present document.

Technical specifications related to the antenna port of radio equipment and radiated emissions from the enclosure port

of radio equipment and combinations of radio and associated ancillary equipment are not included in the present

document. Such technical specifications are normally found in the relevant product standards for the effective use of the

radio spectrum.

The present document, together with ETSI EN 301 489-1 [1], are aimed to cover requirements to demonstrate an

adequate level of electromagnetic compatibility.
2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 301 489-1 (V2.1.0) (04-2016): "ElectroMagnetic Compatibility (EMC) standard for

radio equipment and services; Harmonised Standard covering the essential requirements of

article 3.1(b) of the Directive 2014/53/EU and the essential requirements of article 6 of the

Directive 2014/30/EU; Part 1: Common technical requirements".
NOTE: Available at

http://www.etsi.org/deliver/etsi_en/301400_301499/30148901/02.01.00_20/en_30148901v020100a.pdf.

[2] ETSI EN 300 220-1 (V3.1.0) (05-2016): "Short Range Devices (SRD) operating in the frequency

range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".

ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 489-3 V2.1.0 (2016-09)
2.2 Informative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are not necessary for the application of the present document but they assist the

user with regard to a particular subject area.

[i.1] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the

harmonisation of the laws of the Member States relating to the making available on the market of

radio equipment and repealing Directive 1999/5/EC.

[i.2] ETSI TR 103 088: "Electromagnetic compatibility and Radio spectrum Matters (ERM); Using the

ETSI EN 301 489 series of EMC standards".

[i.3] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request

to the European Committee for Electrotec
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.