SIST EN 10028-4:2009
(Main)Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
This document specifies requirements for weldable steel flat products for the construction of pressure equipment for use at low temperature.
Flacherzeugnisse aus Druckbehälterstählen - Teil 4: Nickellegierte kaltzähe Stähle
In dieser Europäischen Norm sind die Anforderungen an Flacherzeugnisse für Druckbehälter aus den nickellegierten
Stählen nach Tabelle 1 festgelegt.
Zusätzlich gelten die Anforderungen und Begriffe in EN 10028-1:2007+A1:2009.
ANMERKUNG Nach Veröffentlichung dieser Europäischen Norm im EU-Amtsblatt (OJEU) unter der Richtlinie
97/23/EC ist die Annahme ihrer Konformität mit den grundlegenden Anforderungen (ESR) der Richtlinie 97/23/EC auf die
technischen Daten von Werkstoffen in dieser Europäischen Norm (Teil 1 und dieser Teil 4 der Normenreihe) beschränkt,
und es darf nicht angenommen werden, dass damit die Eignung des Werkstoffs für ein bestimmtes Ausrüstungsteil
festgestellt ist. Folglich müssen die in dieser Werkstoffnorm angegebenen technischen Parameter im Hinblick auf die
konstruktiven Anforderungen dieses bestimmten Ausrüstungsteils ermittelt werden, um damit zu verifizieren, dass den
ESR der Richtlinie 97/23/EC entsprochen wird.
Produits plats en aciers pour appareils à pression - Partie 4: Aciers alliés au nickel avec caractéristiques spécifiées à basse température
La présente Norme européenne spécifie les prescriptions relatives aux produits plats pour appareils à pression en
aciers alliés au nickel, telles que spécifiées dans le Tableau 1.
Les prescriptions et définitions de l’EN 10028-1 :2007 + A1 :2009 s’appliquent également.
NOTE Après publication de la présente Norme européenne dans le Journal Officiel de l'UE (OJEU) sous la Directive
97/23/EC, la présomption de conformité aux Exigences Essentielles de Sécurité (ESRs) de la Directive 97/23/EC se limite aux
données techniques des matériaux de la présente Norme européenne (Partie 1 et la présente Partie 4 de la série) et ne
suppose pas l'adéquation du matériau à un élément ou à un équipement spécifique. En conséquence, l'évaluation des données
techniques énoncées dans la présente norme de matériau en fonction des exigences de conception de cet élément spécifique
d'équipement pour vérifier que les ESR de la Directive 97/23/EC sont respectées, doit être effectuée.
Ploščati jekleni izdelki za tlačne posode - 4. del: Jekla, legirana z nikljem, s specificiranimi lastnostmi pri nizkih temperaturah
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flacherzeugnisse aus Druckbehälterstählen - Teil 4: Nickellegierte kaltzähe StähleProduits plats en aciers pour appareils à pression - Partie 4: Aciers alliés au nickel avec caractéristiques spécifiées à basse températureFlat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties77.140.50SROL]GHONLFlat steel products and semi-products77.140.30Jekla za uporabo pod tlakomSteels for pressure purposesICS:Ta slovenski standard je istoveten z:EN 10028-4:2009SIST EN 10028-4:2009en,fr,de01-september-2009SIST EN 10028-4:2009SLOVENSKI
STANDARDSIST EN 10028-4:2003/AC:2006SIST EN 10028-4:20031DGRPHãþD
SIST EN 10028-4:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 10028-4June 2009ICS 77.140.30; 77.140.50Supersedes EN 10028-4:2003
English VersionFlat products made of steels for pressure purposes - Part 4:Nickel alloy steels with specified low temperature propertiesProduits plats en aciers pour appareils à pression - Partie4: Aciers alliés au nickel avec caractéristiques spécifiées àbasse températureFlacherzeugnisse aus Druckbehälterstählen - Teil 4:Nickellegierte kaltzähe StähleThis European Standard was approved by CEN on 14 May 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10028-4:2009: ESIST EN 10028-4:2009
EN 10028-4:2009 (E) 2 Contents Page Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Dimensions and tolerances on dimensions . 4 5 Calculation of mass . 4 6 Classification and designation . 4 6.1 Classification . 4 6.2 Designation . 4 7 Information to be supplied by the purchaser . 4 7.1 Mandatory information . 4 7.2 Options . 5 7.3 Example for ordering . 5 8 Requirements . 5 8.1 Steelmaking process . 5 8.2 Delivery condition . 5 8.3 Chemical composition . 5 8.4 Mechanical properties . 6 8.5 Surface condition. 9 8.6 Internal soundness . 9 9 Inspection . 9 9.1 Types of inspection and inspection documents . 9 9.2 Tests to be carried out . 9 9.3 Retests . 9 10 Sampling . 9 11 Test methods . 9 12 Marking . 9 Annex A (informative)
Guidelines for heat treatment . 10 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC . 11 Bibliography . 12
SIST EN 10028-4:2009
EN 10028-4:2009 (E) 3 Foreword This document (EN 10028-4:2009) has been prepared by Technical Committee ECISS/TC 22 “Steels for pressure purposes - Qualities”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2009, and conflicting national standards shall be withdrawn at the latest by December 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10028-4:2003. This European Standard consists of the following parts, under the general title Flat products made of steels for pressure purposes: Part 1: General requirements Part 2: Non-alloy and alloy steels with specified elevated temperature properties Part 3: Weldable fine grain steels, normalized Part 4: Nickel alloy steels with specified low temperature properties Part 5: Weldable fine grain steels, thermomechanically rolled Part 6: Weldable fine grain steels, quenched and tempered Part 7: Stainless steels NOTE The clauses marked by two points (••) contain information relating to agreements that may be made at the time of enquiry and order. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 97/23/EC. For relationship with EU Directive 97/23/EC, see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 10028-4:2009
EN 10028-4:2009 (E) 4 1 Scope This European Standard specifies requirements for flat products for pressure equipment made of nickel alloy steels as specified in Table 1. The requirements and definitions of EN 10028-1:2007 + A1:2009 also apply. NOTE Once this European Standard is published in the EU Official Journal (OJEU) under Directive 97/23/EC, presumption of conformity to the Essential Safety Requirements (ESRs) of Directive 97/23/EC is limited to technical data of materials in this European Standard (Part 1 and this Part 4 of the series) and does not presume adequacy of the material to a specific item of equipment. Consequently, the assessment of the technical data stated in this material standard against the design requirements of this specific item of equipment to verify that the ESRs of Directive 97/23/EC are satisfied, needs to be done. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10028-1:2007 + A1:2009, Flat products made of steels for pressure purposes – Part 1: General requirements EN 10204:2004, Metallic products – Types of inspection documents 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 10028-1:2007 + A1:2009 apply. 4 Dimensions and tolerances on dimensions See EN 10028-1:2007 + A1:2009. 5 Calculation of mass See EN 10028-1:2007 + A1:2009, 6 Classification and designation 6.1 Classification In accordance with EN 10020, all steel grades covered by this document are alloy special steels. 6.2 Designation See EN 10028-1:2007 + A1:2009. 7 Information to be supplied by the purchaser 7.1 Mandatory information See EN 10028-1:2007 + A1:2009. SIST EN 10028-4:2009
EN 10028-4:2009 (E) 5 7.2
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.