SIST EN 60384-11:2008

Fixed capacitors for use in electronic equipment -- Part 11: Sectional specification - Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors

This part of IEC 60384 applies to fixed direct current capacitors, for rated voltages not exceeding 6 300 V, using as dielectric a polyethylene-terephthalate film and electrodes of thin metal foils. For capacitors with rated voltages exceeding 1 000 V, additional tests and requirements may be specified in the detail specification. The capacitors covered by this standard are intended for use in electronic equipment.

Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 11: Rahmenspezifikation - Festkondensatoren mit einem Dielektrikum aus Polyethylen-Terephthalat und Belägen aus dünnen Metallfolien für Gleichspannung

Condensateurs fixes utilisés dans les équipements électroniques - Partie 11 : Spécification intermédiaire - Condensateurs fixes pour courant continu à diélectrique en film de polytéréphtalate d'éthylène à armatures en feuilles métalliques

La CEI 60384-11:2008 s'applique aux condensateurs fixes pour courant continu, pour des tensions ne dépassant pas 6 300 V, utilisant comme diélectrique un film de polytéréphtalate d'éthylène et des électrodes de feuilles métalliques minces. Pour des condensateurs de tensions assignées ne dépassant pas 1 000 V, d'autres essais et exigences peuvent être spécifiées dans la spécification particulière. Les condensateurs couverts par la présente Norme sont destinés à être utilisés dans des équipements électroniques. La présente Norme a pour objet de prescrire les valeurs assignées et caractéristiques préférentielles, de sélectionner, en se référant à la Norme CEI 60384-1, les procédures d'assurance qualité appropriées, les essais et les méthodes de mesure et de donner les exigences de performances générales pour ce type de condensateur. Les sévérités et les exigences d'essai prescrites dans les spécifications particulières se rapportant à cette spécification intermédiaire doivent présenter des niveaux de performances supérieurs ou égaux, parce que les niveaux de performance inférieurs ne sont pas autorisés. Cette troisième édition annule et remplace la deuxième édition publiée en 1988. Elle constitue une révision mineure des tableaux, valeurs et références.

Fiksni kondenzatorji za elektronsko opremo - 11. del: Področna specifikacija - Fiksni kondenzatorji za enosmerni tok s polietilen tereftalatnim plastnim dielektrikom in kovinsko folijo (IEC 60384-11:2008)

General Information

• Status: Withdrawn
• Publication Date: 04-Jun-2008
• Withdrawal Date: 19-Oct-2022
• ICS: 31.060.10 - Fixed capacitors
• Technical Committee: I11 - Imaginarni 11
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 17-Oct-2022
• Due Date: 09-Nov-2022
• Completion Date: 20-Oct-2022
• Ref Project: EN 60384-11:2008 - Fixed capacitors for use in electronic equipment - Part 11: Sectional specification - Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors

Relations

• Replaced By: SIST EN IEC 60384-11:2019 - Fixed capacitors for use in electronic equipment - Part 11: Sectional specification - Fixed polyethylene-terephthalate film dielectric metal foil DC capacitors (IEC 60384-11:2019)
• Effective Date: 22-Oct-2019
• Replaced By: SIST EN IEC 60384-11:2019 - Fixed capacitors for use in electronic equipment - Part 11: Sectional specification - Fixed polyethylene-terephthalate film dielectric metal foil DC capacitors (IEC 60384-11:2019)
• Effective Date: 07-Jun-2022
• Revised: SIST EN IEC 60384-11:2019 - Fixed capacitors for use in electronic equipment - Part 11: Sectional specification - Fixed polyethylene-terephthalate film dielectric metal foil DC capacitors (IEC 60384-11:2019)
• Effective Date: 17-Oct-2017

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60384-11:2008
01-julij-2008
)LNVQLNRQGHQ]DWRUML]DHOHNWURQVNRRSUHPRGHO3RGURþQDVSHFLILNDFLMD
)LNVQLNRQGHQ]DWRUML]DHQRVPHUQLWRNVSROLHWLOHQWHUHIWDODWQLPSODVWQLP
GLHOHNWULNRPLQNRYLQVNRIROLMR,(&
Fixed capacitors for use in electronic equipment - Part 11: Sectional specification - Fixed
polyethylene terephthalate film dielectric metal foil d.c.capacitors (IEC 60384-11:2008)
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 11:
Rahmenspezifikation - Festkondensatoren mit einem Dielektrikum aus Polyethylen-
Terephthalat und Belägen aus dünnen Metallfolien für Gleichspannung (IEC 60384-
11:2008)
Condensateurs fixes utilisés dans les équipements électroniques - Partie 11 :
Spécification intermédiaire - Condensateurs fixes pour courant continu à diélectrique en
film de polytéréphtalate d'éthylène à armatures en feuilles métalliques (CEI 60384-
11:2008)
Ta slovenski standard je istoveten z: EN 60384-11:2008
ICS:
31.060.10 Fiksni kondenzatorji Fixed capacitors
SIST EN 60384-11:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN 60384-11

NORME EUROPÉENNE
April 2008
EUROPÄISCHE NORM

ICS 31.060.30


English version


Fixed capacitors for use in electronic equipment -
Part 11: Sectional specification -
Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors
(IEC 60384-11:2008)


Condensateurs fixes utilisés  Festkondensatoren zur Verwendung
dans les équipements électroniques - in Geräten der Elektronik -
Partie 11: Spécification intermédiaire - Teil 11: Rahmenspezifikation -
Condensateurs fixes pour courant continu Festkondensatoren mit einem
à diélectrique en film de polytéréphtalate Dielektrikum aus Polyethylen-Terephthalat
d'éthylène à armatures und Belägen aus dünnen Metallfolien
en feuilles métalliques für Gleichspannung
(CEI 60384-11:2008) (IEC 60384-11:2008)




This European Standard was approved by CENELEC on 2008-03-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60384-11:2008 E

---------------------- Page: 2 ----------------------

EN 60384-11:2008 - 2 -
Foreword
The text of document 40/1839/CDV, future edition 3 of IEC 60384-11, prepared by IEC TC 40, Capacitors
and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel Unique Acceptance
Procedure and was approved by CENELEC as EN 60384-11 on 2008-03-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-12-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2011-03-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60384-11:2008 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60384-14 NOTE  Harmonized as EN 60384-14:2005 (not modified).
__________

---------------------- Page: 3 ----------------------

- 3 - EN 60384-11:2008
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

1) 2)
IEC 60062 - Marking codes for resistors and capacitors EN 60062 2005
+ corr. January 2007


IEC 60063 1963 Preferred number series for resistors - -
+ A1 1967 and capacitors
+ A2 1977


1) 2)
IEC 60068-1 - Environmental testing - EN 60068-1 1994
Part 1: General and guidance


IEC 60384-1 (mod) 1999 Fixed capacitors for use in electronic EN 60384-1 2001
equipment - + corr. October 2001
Part 1: Generic specification


IEC 60410 1973 Sampling plans and procedures - -
for inspection by attributes


1)
ISO 3 - Preferred numbers - Series of preferred - -
numbers




1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 4 ----------------------

IEC 60384-11
Edition 3.0 2008-02
INTERNATIONAL
STANDARD

QC 300100
Fixed capacitors for use in electronic equipment –
Part 11: Sectional specification – Fixed polyethylene-terephthalate film dielectric
metal foil d.c. capacitors


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
U
ICS 31.060.30 ISBN 2-8318-9608-8

---------------------- Page: 5 ----------------------

– 2 – 60384-11 © IEC:2008(E)
CONTENTS
FOREWORD.4

1 General .6
1.1 Scope.6
1.2 Object .6
1.3 Normative references .6
1.4 Information to be given in a detail specification .6
1.4.1 Outline drawing and dimensions .7
1.4.2 Mounting .7
1.4.3 Ratings and characteristics.7
1.4.4 Marking .8
1.5 Terms and definitions .8
1.6 Marking .8
2 Preferred ratings and characteristics .9
2.1 Preferred characteristics .9
2.1.1 Preferred climatic categories .9
2.2 Preferred values of ratings .9
2.2.1 Rated capacitance (C ).9
R
2.2.2 Tolerance on rated capacitance.9
2.2.3 Rated voltage (U ).9
R
2.2.4 Category voltage (U ) .9
C
2.2.5 Rated temperature.10
3 Quality assessment procedures.10
3.1 Primary stage of manufacture.10
3.2 Structurally similar components.10
3.3 Certified records of released lots.10
3.4 Qualification approval.10
3.4.1 Qualification approval on the basis of the fixed sample size
procedure .10
3.4.2 Tests .11
3.5 Quality conformance inspection.16
3.5.1 Formation of inspection lots.16
3.5.2 Test schedule .17
3.5.3 Delayed delivery.17
3.5.4 Assessment levels.17
4 Test and measurement procedures.18
4.1 Visual examination and check of dimensions.18
4.2 Electrical tests.18
4.2.1 Voltage proof.18
4.2.2 Capacitance .18
4.2.3 Tangent of loss angle (tan δ) .19
4.2.4 Insulation resistance.19
4.2.5 Characteristics depending on temperature (if required in the detail
specification) .20
4.3 Robustness of terminations .21
4.3.1 Initial measurements .21
4.4 Resistance to soldering heat .21

---------------------- Page: 6 ----------------------

60384-11 © IEC:2008(E) – 3 –
4.4.1 Conditions .21
4.4.2 Final inspection, measurements and requirements .21
4.5 Solderability .21
4.6 Rapid change of temperature .21
4.6.1 Initial measurement .21
4.6.2 Number of cycles: 5.22
4.7 Vibration.22
4.8 Bump .22
4.8.1 Initial measurements .22
4.8.2 Severities .22
4.8.3 Final inspection, measurements and requirements .22
4.9 Shock.22
4.9.1 Initial measurements .22
4.10 Climatic sequence .23
4.10.1 Initial measurements .23
4.10.2 Dry heat .23
4.10.3 Damp heat, cyclic, Test Db, first cycle .23
4.10.4 Cold .23
4.10.5 Low air pressure.23
4.10.6 Damp heat, cyclic, Test Db, remaining cycles .24
4.11 Damp heat, steady state.24
4.11.1 Initial measurements .24
4.12 Endurance.24
4.13 Component solvent resistance (if applicable).25
4.14 Solvent resistance of the marking (if applicable).25

Bibliography.26

Table 1 – Fixed sample size test plan for qualification approval – Assessment level EZ.12
Table 2 – Test schedule for qualification approval.13
Table 3 – Lot-by-lot inspection .17
Table 4 – Periodic tests .18
Table 5 – Test voltages.18
Table 6 – Insulation resistance .19
Table 7 – Correction factor dependent on test temperature.20
Table 8 – Characteristics at lower category temperature.20
Table 9 – Characteristics at upper category temperature .21
Table 10 – Acceleration and duration of the pulse.23
Table 11 – Endurance test .24

---------------------- Page: 7 ----------------------

– 4 – 60384-11 © IEC:2008(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
_______________

FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 11: Sectional specification –
Fixed polyethylene-terephthalate film
dielectric metal foil d.c. capacitors


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-11 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment.
This third edition cancels and replaces the second edition published in 1988 and constitutes a
minor revision related to tables, figures and references.
The text of this standard is based on the following documents:
CDV Report on voting
40/1839/CDV 40/1864/RVC
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 8 ----------------------

60384-11 © IEC:2008(E) – 5 –
The list of all parts of the IEC 60384 series, under the (new) general title Fixed capacitors for
use in electronic equipment, can be found on the IEC web site.
The QC number that appears on the front cover of this publication is the specification number
in the IEC Quality Assessment System for Electronic Components (IECQ).
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

---------------------- Page: 9 ----------------------

– 6 – 60384-11 © IEC:2008(E)
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –

Part 11: Sectional specification –
Fixed polyethylene-terephthalate film
dielectric metal foil d.c. capacitors



1 General
1.1 Scope
This part of IEC 60384 applies to fixed direct current capacitors, for rated voltages not
exceeding 6 300 V, using as dielectric a polyethylene-terephthalate film and electrodes of thin
metal foils. For capacitors with rated voltages exceeding 1 000 V, additional tests and
requirements may be specified in the detail specification.
The capacitors covered by this standard are intended for use in electronic equipment.
NOTE Capacitors for radio interference suppression are not included, but are covered by IEC 60384-14 (see
bibliography).
1.2 Object
The object of this standard is to prescribe preferred ratings and characteristics and to select
from IEC 60384-1, the appropriate quality assessment procedures, tests and measuring
methods and to give general performance requirements for this type of capacitor. Test
severities and requirements prescribed in detail specifications referring to this sectional
specification shall be of equal or higher performance level, because lower performance levels
are not permitted.
1.3 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60062, Marking codes for resistors and capacitors
1)
IEC 60063, Preferred number series for resistors and capacitors
IEC 60068-1, Environmental testing – Part 1: General and guidance
IEC 60384-1:1999, Fixed capacitors for use in electronic equipment – Part 1: Generic specification
IEC 60410:1973, Sampling plans and procedures for inspection by attributes
ISO 3: Preferred numbers – Series of preferred numbers.
1.4 Information to be given in a detail specification
Detail specifications shall be derived from the relevant blank detail specification.
—————————
1)
Second edition (1963) incorporating Amendments 1 (1967) and 2 (1977).

---------------------- Page: 10 ----------------------

60384-11 © IEC:2008(E) – 7 –
Detail specifications shall not specify requirements inferior to those of the generic, sectional
or blank detail specification. When more severe requirements are included, they shall be
listed in 1.9 of the detail specification and indicated in the test schedules, for example by an
asterisk.
NOTE The information given in 1.4.1 may, for convenience, be presented in tabular form.
The following information shall be given in each detail specification and the values quoted
shall preferably be selected from those given in the appropriate clause of this sectional
specification.
1.4.1 Outline drawing and dimensions
There shall be an illustration of the capacitor as an aid to easy recognition and for comparison
of the capacitor with others. Dimensions and their associated tolerances, which affect
interchangeability and mounting, shall be given in the detail specification. All dimensions shall
preferably be stated in millimetres, however, when the original dimensions are given in inches,
the converted metric dimensions in millimetres shall be added.
Normally the numerical values shall be given for the length of the body, the width and height
of the body and the wire spacing, or for cylindrical types, the body diameter, and the length
and diameter of the terminations. When necessary, for example when a number of items
(capacitance values/voltage ranges) are covered by a detail specification, the dimensions and
their associated tolerances shall be placed in a table below the drawing.
When the configuration is other than described above, the detail specification shall state such
dimensional information as will adequately describe the capacitor. When the capacitor is not
designed for use on printed boards, this shall be clearly stated in the detail specification.
1.4.2 Mounting
The detail specification shall specify the method of mounting to be applied for normal use and
for the application of the vibration and the bump or shock tests. The capacitors shall be
mounted by their normal means. The design of the capacitor may be such that special
mounting fixtures are required in its use. In this case the detail specification shall describe the
mounting fixtures and they shall be used in the application of the vibration and bump or shock
tests.
1.4.3 Ratings and characteristics
The ratings and characteristics shall be in accordance with the relevant clauses of this
specification, together with the following:
1.4.3.1 Rated capacitance range
See 2.2.1.
NOTE When products approved to the detail specification have different ranges, the following statement should
be added: "The range of values available in each voltage range is given in the qualified products list".
1.4.3.2 Particular characteristics
Additional characteristics may be listed, when they are considered necessary to specify
adequately the component for design and application purposes.
1.4.3.3 Soldering
The detail specification shall prescribe the test methods, severities and requirements
applicable for the solderability and the resistance to soldering heat test.

---------------------- Page: 11 ----------------------

– 8 – 60384-11 © IEC:2008(E)
1.4.4 Marking
The detail specification shall specify the content of the marking on the capacitor and on the
package. Deviations from 1.6 of this sectional specification, shall be specifically stated.
1.5 Terms and definitions
For the purposes of this document the terms and definitions of IEC 60384-1, as well as the
following apply.
1.5.1
rated voltage (U )
R
maximum d.c. voltage which may be applied continuously to a capacitor at the rated
temperature
NOTE The sum of the d.c. voltage and the peak a.c. voltage applied to the capacitor shall not exceed the rated
voltage. The value of the peak a.c. voltage shall not exceed the following percentages of the rated voltage at the
frequencies stated and shall not be greater than 280 V,
50 Hz 20 %
100 Hz 15 %
1 000 Hz 3 %
10 000 Hz 1 %

unless otherwise specified in the detail specification.
1.6 Marking
See 2.4 of IEC 60384-1, with the following details:
1.6.1 The information given in the marking is normally selected from the following list. The
relative importance of each item is indicated by its position in the list:
a) rated capacitance (in clear or code according to IEC 60062);

b) rated voltage (d.c. voltage may be indicated by the symbol     or );
c) tolerance on rated capacitance;
d) category voltage;
e) year and month (or week) of manufacture;
f) manufacturer's name or trade mark;
g) climatic category;
h) manufacturer's type designation;
i) reference to the detail specification.
1.6.2 The capacitor shall be clearly marked with a), b) and c) above and with as many as
possible of the remaining items as is considered necessary. Any duplication of information in
the marking on the capacitor should be avoided.
1.6.3 The package containing the capacitor(s) shall be clearly marked with all the
information listed in 1.6.1.
1.6.4 Any additional marking shall be so applied that no confusion can arise.

---------------------- Page: 12 ----------------------

60384-11 © IEC:2008(E) – 9 –
2 Preferred ratings and characteristics
2.1 Preferred characteristics
The values given in detail specifications shall preferably be selected from the following:
2.1.1 Preferred climatic categories
The capacitors covered by this specification are classified into climatic categories according
to the general rules given in IEC 60068-1.
NOTE For the tests in the IEC 60068 series of publications, the editions referenced in the applicable test clauses
of the generic specification are used.
The lower and upper category temperatures and the duration of the damp heat, steady state
test shall be chosen from the following.
Lower category temperature: –55 °C, –40 °C and –25 °C.
Upper category temperature: +85 °C, +100 °C, +105 °C and +125 °C.
Duration of the damp heat, steady state test: 4, 10, 21 and 56 days.
The severities for the cold and dry heat tests are the lower and upper category temperatures
respectively.
2.2 Preferred values of ratings
2.2.1 Rated capacitance (C )
R
Preferred values of rated capacitance are:
1 μF, 1,5 μF, 2,2 μF, 3,3 μF, 4,7 μF and 6,8 μF and their decimal multiples.
These values conform to the E6 series of preferred values given in IEC 60063.
If other values are required they shall preferably be chosen from the E12 series.
2.2.2 Tolerance o
...