iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN 16659:2024

(Main)

Bitumen and bituminous binders - Multiple Stress Creep and Recovery Test (MSCRT)

Bitumen and bituminous binders - Multiple Stress Creep and Recovery Test (MSCRT)

This document specifies a test method for the determination of per cent recovery and non-recoverable creep compliance of bitumen and bituminous binders by means of Multiple Stress Creep and Recovery (MSCR) testing. The MSCR test is conducted using the Dynamic Shear Rheometer (DSR) in creep mode at a specified temperature.
The per cent recovery at multiple stress levels is intended to determine the presence of elastic response and stress dependence of bituminous binders. The non-recoverable creep compliance at multiple stress levels is intended as an indicator for the sensitivity to permanent deformation and stress dependence of bituminous binders.
This document is applicable to un-aged, aged, stabilised and recovered bituminous binders. The test procedure in accordance with this document is not applicable for bituminous binders with particles larger than 250 μm (e.g. filler material, granulated rubber).
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Bitumen und bitumenhaltige Bindemittel - MSCR-Prüfung (Multiple Stress Creep and Recovery Test)

Bitumes et liants bitumineux- Essai de fluage-recouvrance sous contraintes répétées (essai MSCR)

Bitumen in bitumenska veziva - Ponavljajoči obremenilni in razbremenilni preskus lezenja (MSCRT)

General Information

Status
Not Published
Public Enquiry End Date
16-Apr-2024
ICS
75.140 - Waxes, bituminous materials and other petroleum products
91.100.50 - Binders. Sealing materials
Technical Committee
VLA - Water proofing
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
31-Jan-2024
Due Date
19-Jun-2024
Ref Project
prEN 16659 - Bitumen and bituminous binders - Multiple Stress Creep and Recovery Test (MSCRT)

Relations

Replaces
SIST EN 16659:2016 - Bituminen and Bituminous Binders - Multiple Stress Creep and Recovery Test (MSCRT)
Effective Date
12-Feb-2024

Buy Standard

prEN 16659:2024prEN 16659:2024
PreviousNext
Draft
prEN 16659:2024
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 16659:2024
01-april-2024
Nadomešča:
SIST EN 16659:2016
Bitumen in bitumenska veziva - Ponavljajoči obremenilni in razbremenilni preskus
lezenja (MSCRT)
Bitumen and bituminous binders - Multiple Stress Creep and Recovery Test (MSCRT)
Bitumen und bitumenhaltige Bindemittel - MSCR-Prüfung (Multiple Stress Creep and
Recovery Test)
Bitumes et liants bitumineux- Essai de fluage-recouvrance sous contraintes répétées
(essai MSCR)
Ta slovenski standard je istoveten z: prEN 16659
ICS:
75.140 Voski, bitumni in drugi naftni Waxes, bituminous materials
proizvodi and other petroleum products
91.100.50 Veziva. Tesnilni materiali Binders. Sealing materials
oSIST prEN 16659:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 16659:2024

---------------------- Page: 2 ----------------------
oSIST prEN 16659:2024


DRAFT
EUROPEAN STANDARD
prEN 16659
NORME EUROPÉENNE

EUROPÄISCHE NORM

January 2024
ICS 75.140; 91.100.50 Will supersede EN 16659:2015
English Version

Bitumen and bituminous binders - Multiple Stress Creep
and Recovery Test (MSCRT)
Bitumes et liants bitumineux- Essai de fluage- Bitumen und bitumenhaltige Bindemittel - MSCR-
recouvrance sous contraintes répétées (essai MSCR) Prüfung (Multiple Stress Creep and Recovery Test)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 336.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16659:2024 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 16659:2024
prEN 16659:2024 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 5
5 Apparatus . 5
6 Preparation of rheometer . 6
6.1 Set up . 6
6.2 Zero gap setting . 6
7 Sample preparation .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 16346:2024(Main)
Bitumen and bituminous binders - Determination of breaking behaviour and immediate adhesivity of cationic bituminous emulsions
EN 16346:2023

This document specifies a method for the determination of the breaking and immediate adhesivity behaviour of cationic bituminous emulsions in contact with aggregate. The method applies to emulsions used for surface dressing and similar applications and can be used for formulation as well as for production control purposes.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12596:2023(Main)
Bitumen and bituminous binders - Determination of dynamic viscosity by vacuum capillary
EN 12596:2023

This document specifies a method for the determination of the dynamic viscosity of bituminous binders by means of a vacuum capillary viscometer at 60 °C in a range between 0,003 6 Pa⋅s and 580 000 Pa⋅s. Other temperatures are possible if calibration constants are known. Bituminous emulsions and non-newtonian binders (e.g. some polymer modified bitumen) are not within the scope of this method.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14770:2023(Main)
Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR)
EN 14770:2023

This document specifies a general method of using a dynamic shear rheometer (DSR) for measuring the rheological properties of bituminous binders. The procedure involves determining the complex shear modulus and phase angle of binders over a range of test frequencies and test temperatures when tested in oscillatory shear.
From the test, the complex shear modulus, |G*|, and its phase angle, δ, at a given temperature and frequency are calculated, as well as the components G' and G'' of the complex shear modulus.
This method is applicable to un-aged, aged and recovered bituminous binders.
WARNING -The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12595:2023(Main)
Bitumen and bituminous binders - Determination of kinematic viscosity
EN 12595:2023

This document specifies a method for the determination of the kinematic viscosity of bituminous binders at 60 °C and 135 °C, in a range from 6 mm2/s to 300 000 mm2/s. Other temperatures are possible if calibration constants are known. Bituminous emulsions are not covered within the scope of this method.
Results for this method can be used to calculate dynamic viscosity when the density of the test material is known or can be determined.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to identify the hazards and assess the risks involved in performing this test method and to implement sufficient control measures to protect individual operators (and the environment). This includes appropriate safety and health practices and determination of the applicability of regulatory limitations prior to use.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14769:2023(Main)
Bitumen and bituminous binders - Accelerated long-term ageing conditioning by a Pressure Ageing Vessel (PAV)
EN 14769:2023

This document specifies an accelerated ageing/conditioning procedure for bituminous binders. The procedure involves ageing trays of binder at elevated temperatures under pressurized conditions in a pressure ageing vessel (PAV).
NOTE   For binders to be used in hot asphalt applications, the pre-conditioning of the sample can be performed using one of the methods in the EN 12607 series. For binders to be used in bituminous emulsion and cut-back or fluxed applications, the stabilizing of the sample is such that there are no volatiles remaining.
WARNING — The use of this document can involve hazardous materials, operations and equipment, in particular, the use of a high pressure ageing vessel. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate health and safety practices and determine the applicability of regulatory limitations prior to use. If there is the likelihood of volatile components being present in a binder, this procedure is not used.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 14771:2023(Main)
Bitumen and bituminous binders - Determination of the flexural creep stiffness - Bending Beam Rheometer (BBR)
EN 14771:2023

This document specifies a method for the determination of the flexural creep stiffness of bitumen and
bituminous binders in the range of 30 MPa to 1 GPa by means of the bending beam rheometer.
The method can be applied to a variety of bitumens, including unmodified as well as modified binders, as
fresh (unused) binders, as well as binders after laboratory ageing conditioning (e.g. EN 12607-1,
EN 14769), and also binders that have been recovered from asphalt mixtures.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This
document does not purport to address all of the safety problems associated with its use. It is the
responsibility of the user of this document to establish appropriate safety and health practices and to
determine the applicability of regulatory limitations prior to use.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12846-1:2023(Main)
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 1: Bituminous emulsions
EN 12846-1:2022

This document specifies a method for the determination of the efflux time at 40 °C of bituminous emulsions in seconds using an efflux viscometer. Alternative test temperature is 50 °C.
NOTE   The procedure described in this document can also be followed to determine efflux time at other temperatures such as 25 °C.
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12846-2:2023(Main)
Bitumen and bituminous binders - Determination of efflux time by the efflux viscometer - Part 2: Cut-back and fluxed bituminous binders
EN 12846-2:2022

This document specifies a method for the determination of the efflux time at 25 °C of petroleum cut-back and fluxed bituminous binders in seconds using an efflux viscometer. Alternative test temperatures are 40 °C, 50 °C and 60 °C.
WARNING - The use of this document involves hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 12850:2022(Main)
Bitumen and bituminous binders - Determination of the pH value of bituminous emulsions
EN 12850:2022

This document specifies a method for measuring the pH value of bituminous emulsions.
It is applicable to anionic, cationic bituminous emulsions and bituminous emulsions prepared by means of non-ionic surfactant.
In certain circumstances, the pH value can provide an indication of the ionic character of a bituminous emulsion. However, this indication should be confirmed by a particle polarity test conforming to EN 1430 [1].
WARNING - The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

  • Standard
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17643:2022(Main)
Bitumen and bituminous binders - Determination of equi-shear modulus temperature and phase angle using a Dynamic Shear Rheometer (DSR) - BTSV test
EN 17643:2022

This document specifies the Binder Fast Characterization Test (for short: BTSV test, German: Bitumen-Typisierungs-Schnell-Verfahren). The test is conducted using a Dynamic Shear Rheometer (DSR). It is used to quickly characterize bitumen and bituminous binders and to assess the deformation behaviour at high service temperatures.
This document deals with the testing of fresh paving grade bitumen and modified bitumen, as conditioned in a laboratory ageing procedure (e.g. EN 12607 1, EN 14769) and also as recovered from asphalt mixtures. The test procedure in accordance with this document is not applicable for bituminous binders with particles larger than 250 μm (e.g. filler material, granulated rubber).
NOTE   The test procedure has not been applied on bituminous binders recovered from bitumen emulsions yet.
The test determines the temperature and the associated phase angle at which a bituminous binder exhibits a defined complex shear modulus in stress-controlled oscillation mode at constant frequency and with continuous increase of the test temperature.
WARNING — The use of this document can involve hazardous materials, operations and equipment. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety and health practices and to ensure that regulatory requirements are fulfilled prior to application of this document.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day